Smeg LVS319S Bedienungsanleitung
Contents
1
1.
Description of the controls ________________________________3
2.
Operating instructions___________________________________ 13
3.
Cleaning and maintenance_______________________________26
4.
Troubleshooting _______________________________________ 30
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need use your dishwasher safely, correctly and in the
most satisfactory manner.
Following the cleaning instructions provided here will keep your
dishwasher's performance at peak levels in the long term.
USER INSTRUCTIONS: these consist of recommendations for using the
appliance, a description of its controls and of the correct cleaning and
maintenance procedures.
User instructions
2
1. Description of the controls
1.1 Front panel
The ON/OFF is on the top edge of the panel, and all the dishwasher’s
other controls and monitoring devices are on the central display.
Programming and option selection are only possible with the door
closed.
NOTA:
The displays illustrated in the instruction manual are purely guideline;
symbols, programs and options may vary depending on the model
purchased.
User instructions
3
VERSION WITHOUT OPTIONS
1 ON/OFF BUTTON
2 SELECTION PROGRAMS BUTTON
3 START/PAUSE BUTTON
4 PROGRAMS LIGHTS
5 PHASES/PROGRAM LIGHTS
6
WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT
The light flashes to indicate that the appliance is in “water
hardness adjustment” mode.
SALT WARNIN LIGHT
Illumination of this light denotes a regenerating salt warning level.
7 NO RINSE AID LIGHT
User instructions
4
VERSION WITH OPTIONS
1 ON/OFF BUTTON
2 SELECTION PROGRAMS BUTTON
3 START/PAUSE BUTTON
4 PROGRAMS LIGHTS
5 PHASES/PROGRAM LIGHTS +
PROGRAM DELAY (if the option is included)
6
WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT
The light flashes to indicate that the appliance is in “water
hardness adjustment” mode.
SALT WARNIN LIGHT
Illumination of this light denotes a regenerating salt warning level.
7 NO RINSE AID LIGHT
8 OPTIONS (on some models only)
User instructions
5
<<OPTIONS (8)>>
Depending on the model, this zone may contain one or more of the
following options, identified by the relative symbols and described in
more detail in the relevant sections of the manual.
It is not possible to select any options when the soak program is being
used. All options except "Flexi Tabs" are disabled at the end of the
wash cycle. To disable the “Flexi Tabs” option, press the relative
button (the light goes out).
Flexi Tabs
Specifically for the use of products which contain salt and
rinse aid as well as detergent.
HYCLEAN
Adds a final antibacterial rinse to the selected program.
Spread HALF LOAD WASH
Allows washing of just a few dishes placed in both baskets.
PROGRAM DELAY
Allows the program to be set to start with a delay of 3, 6, 9 or
12 hours.
PROGRAMS TABLE
The manual contains the programs table for several models. To find the
table for your dishwasher, compare the program symbols at the top of the
table with those on your control panel.
User instructions
6
PROGRAMS TABLE
PROGRAMME
NUMBER
& SYMBOL
LOAD CROCKERY AND
CUTLERY
PROGRAM
PROGRESS
DURATION
CONSUMPTION
MINUTES
(1)
WATER
LITRES
POWER
KWh (1)
1
SOAK
Pans and dishes awaiting
completion of the load Cold prewash
15 3,5 0,02
2 RAPID
Dishes with light dirt,
washed immediately after
use
Wash at 38°C
Rinse at 50°C
27
6,5 0,70
3 ECO (*)
EN 50242
Dishes with normal dirt,
even with dried-on
residues
Cold prewash
Wash at 45°C
Rinse at 65°C
Dry
**
** **
4 HALF LOAD
Half load of dishes with
normal dirt, washed
immediately after use.
Wash at 65°C
Cold rinse
Rinse at 70°C
Dry
90
11 1,20
5
ULTRA
CLEAN
****
Very dirty pans and
dishes, even with dried-on
residues.
Hot prewash
Wash at 70°C
Cold rinse (2)
Rinse at 70°C
Dry
155
15,5 1,60
The
ULTRA CLEAN
program terminate with an extra anti-bacteria rinse that ensures a further
reduction in the bacteria level. If the temperature falls during this stage of the program (e.g.
because the door is opened or due to a power blackout), the program lights (4) flash to warn
that the anti-bacteria effect is not guaranteed.
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
User instructions
7
NOTES AND REFERENCES
Only
run the soak program with half loads.
Options cannot be used with the soak program.
* Standard programme under
EN 50242
.
** See information sheet provided
***
IEC/DIN
reference programme.
**** Reference program for laboratories: Detergent:
20g
in the
dispenser
+
10g
in
the door or tablet. Configuration: see photo in “Using the baskets”.
(1) Program consumption and duration figures have been measured in
accordance with the EN 50242 standard. Values may vary depending on
intake water and room temperatures and the type and quantity of dishes
loaded.
(2) 1 or 2 cold rinses depending on the model.
REFERENCES for the ENERGY LABEL supplied with the dishwasher:
- Annual energy consumption is based on 280 standard wash cycles with cold
water and consumption of low-energy operating modes. Actual consumption
depends on the way in which the appliance is used.
- Water consumption is based on 280 standard wash cycles. Actual
consumption depends on the way in which the appliance is used.
- Information refers to the EN 50242 STANDARD programme (identified in the
programmes table), which is the most effective in terms of combined energy
and water consumption. The programme is recommended for dishes with a
normal level of dirt.
- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”
(maximum efficiency).
User instructions
8
1.2 Washing programs
The dishwasher is equipped with a control panel, described in chapter
"3. Description of the controls", from which it is possible to carry out all
the power switch-on, switch-off and programming operations.
Before starting a washing program make sure that:
•The water supply tap is open.
•The correct amount of detergent has been added to the
dispenser.
•The baskets have been correctly loaded.
•The spray arms are able to rotate freely and without
obstruction.
•The dishwasher door is securely closed.
SWITCHING ON
When the ON/OFF button (1) is pressed, the dishwasher switches on.
PROGRAMMING
Programming operations are only possible with the door closed.
PROGRAM SELECTION
Press the
PROGRAM SELECTION
button
(2)
several times until the light
of the program required comes on.
Inhaltsverzeichnis
Andere Smeg Spülmaschine Handbücher
Smeg
Smeg DI612M Bedienungsanleitung
Smeg
Smeg LSPU8612S Bedienungsanleitung
Smeg
Smeg STX.1 Bedienungsanleitung
Smeg
Smeg PL 942 EB Bedienungsanleitung
Smeg
Smeg LVD613X Bedienungsanleitung
Smeg
Smeg Dishwasher DWI710 Bedienungsanleitung
Smeg
Smeg CW 420 Bedienungsanleitung
Smeg
Smeg Dishwasher Bedienungsanleitung
Smeg
Smeg BLV1VE Bedienungsanleitung
Smeg
Smeg PL614WH Bedienungsanleitung
Smeg
Smeg DI361C Bedienungsanleitung
Smeg
Smeg STU8642 Bedienungsanleitung
Smeg
Smeg PL8605XTD Bedienungsanleitung
Smeg
Smeg DC136LW Bedienungsanleitung
Smeg
Smeg CWH510D Bedienungsanleitung
Smeg
Smeg Universale DWA4510X Bedienungsanleitung
Smeg
Smeg STC700 Bedienungsanleitung
Smeg
Smeg DWD44BL.1 Bedienungsanleitung
Smeg
Smeg CWG400B Bedienungsanleitung
Smeg
Smeg PL672EB Bedienungsanleitung
