Smeg ST2FABPK Bedienungsanleitung

INSTRUCTION MANUAL

Contents

1. Description of the controls _______________________________2

2. Operating instructions__________________________________11

3. Cleaning and maintenance______________________________26

4. Troubleshooting ______________________________________30

Thank you for choosing one of our products.

You are advised to read this manual carefully; it contains all the

information you need to use your dishwasher safely, correctly and in the

most satisfactory manner.

Following the cleaning instructions provided here will keep your

dishwasher's performance at peak levels in the long term.

USER INSTRUCTIONS: these consist of recommendations for using the

appliance, a description of its controls and of the correct cleaning and

maintenance procedures.

User instructions

1. Description of the controls

1.1 Upper panel

All the dishwasher controls are grouped on the upper panel. Switch-on,

programming, switch-off etc. procedures are only possible when the door

is open.

1 ON/OFF BUTTON

Pressing this button energises the appliance.

2 SELECTED PROGRAM INDICATOR LIGHTS

Illumination of this light denotes the program selected and the

occurrence of a fault (troubleshooting).

3 PROGRAM SELECTION BUTTON

By pressingthisbuttoninsequenceit is possible toselect thedesired

program.

WATER HARDNESS ADJUSTMENT ON INDICATOR LIGHT

The light flashes to indicate that the appliance is in “water hardness

adjustment” mode.

SALT WARNIN LIGHT (on some models only)

If the symbol is present, illumination of this light denotes a

regenerating salt warning level.

5 RINSE AID WARNING LIGHT (on somemodels only)

Illumination of this light signals that rinse aid dispenser is empty.

QUICK TIME + EXTRA OPTION BUTTON

(see “EXTRA OPTIONS” section)

The button controls selection of the quick time programs.

(see table).

7 QUICK TIME PROGRAM LIGHT

Illuminates to indicate that one of the extra programs (see table) is

going to be executed.

User instructions

8 ENERSAVE OPTION + EXTRA OPTION BUTTON

(see “EXTRA OPTIONS” section)

Press the button toenable/disablethe option.

9 ENERSAVE OPTION LIGHT

Illuminates to indicate that the function is activated.

HALF LOAD BUTTON

Press this button to activate the half load wash option.

"Flexi Tabs" OPTION (EXTRA OPTION) LIGHT

Illuminates to indicate that the function is activated.

HALF LOAD LIGHT

Illuminates to indicate that the function is activated.

PROGRAM DELAY BUTTON

Press this button to delay the start of the program.

INFORMATION DISPLAY

N.B.: symbols and styling are guideline and may vary depending on

the model or version of the dishwasher purchased.

SETTING THE WASHING PROGRAM AND SWITCHING ON

To select the most suitable program for the dishes to be washed refer to

the table below, which indicates the most appropriate program according

to dish type and degree of soiling.

After using the table to identify the most appropriate washing program:

press the ON/OFF button (1) and wait for the PROGRAM

INDICATOR LIGHT (2) to illuminate;

keep pressing the PROGRAM SELECTION button (3) until the

indicator light corresponding to the desired program illuminates;

close the door; after about 2" the program will start. While it is in

progress, the relative LIGHT will flash (indicating that the program is

being executed).

User instructions

PROGRAMS TABLE

PROGRAMME

NUMBER

& SYMBOL

LOAD CROCKERY AND

CUTLERY PROGRAM

PROGRESS

DURATION

CONSUMPTION

MINUTES

(1)

WATER

LITRES POWER

KWh (1)

1SOAK

Pans and dishes awaiting

completion of the load Cold prewash 15 3,5 0,02

2 GLASS

Glass, china and mixed

dishes with light dirt.

Wash at 45°C

Cold rinse

Rinse at 70°C

Dry

9,5 1,10

3 ECO (*)

EN 50242

Dishes with normal dirt,

even with dried-on

residues

Wash at 45°C

Cold rinse

Rinse at 55°C

Dry

** **

AUTO 45-65

IEC/DIN***

Pans and dishes with

normal dirt, even with

dried-on residues.

When the "AUTO" program is selected, the dishwasher

recognises the type of dirt and automatically adjusts the

washing parameters as appropriate.

5 ULTRA

CLEAN

****

Very dirty pans and

dishes, even with dried-on

residues.

Hot prewash

Wash at 70°C

Cold rinse (2)

Rinse at 70°C

Dry

160

15,5 1,70

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

The

ULTRA CLEAN

program terminate with an extra anti-bacteria rinse that ensures

a further reduction in the bacteria level. If the temperature falls during this stage of the

program (e.g. because the door is opened or due to a power blackout), the program

lights flash to warn that the anti-bacteria effect is not guaranteed.

If the dishwasher door is open or not properly closed, the washing cycle

will not start.

User instructions

QUICK TIME PROGRAMS

(see relevant section for explanation of functioning modes)

PROGRAMME

NUMBER E

SYMBOL

LOAD CROCKERY AND

CUTLERY

PROGRAM

PROGRESS

DURATION

CONSUMPTION

MINUTI

(1)

WATER

LITRES

POWER

KWh (1)

6 RAPID 27’

Dishes with light dirt,

washed immediately after

use

Wash at 38°C

Rinse at 50°C

6,5 0,70

DELICATE

QUICK

Delicate dishes with normal

dirt.

Cold prewash

Wash at 50°C

Cold rinse

Rinse at 70°C

10,5 1,15

ECO

QUICK

Dishes with normal dirt,

washed immediately after

use.

Cold prewash

Wash at 60°C

Cold rinse

Rinse at 70°C

12,5 1,25

NORMAL

QUICK

Dishes with normal dirt,

washed immediately after

use.

Cold prewash

Wash at 70°C

Cold rinse

Rinse at 70°C

13 1,40

STRONG

and FAST

Mixed dishes with normal

dirt without dried-on

residues.

Wash at 65°C

Cold rinse

Rinse at 70°C

10 1,20

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

If the dishwasher door is open or not properly closed, the washing cycle

will not start.

User instructions

NOTES AND REFERENCES

Only

run the soak program with half loads.

Options cannot be used with the soak program.

The ENERSAVE option (if featured) cannot be used with soak, ultra clean, or any

programs which do not include the final drying stage.

* Standard programme under

EN 50242

. If present, the

ENERSAVE

option must

be enabled.

** See information sheet provided

***

IEC/DIN

reference programme. If present, the

ENERSAVE

option must

enabled.

**** Reference program for laboratories: Detergent:

20g

in the

dispenser

10g

the door or tablet. Configuration: see photo in “Using the baskets”.

(1) The cycle duration and power consumption may vary according to the water

and room temperatures, and the type and amount of dishes.

REFERENCES for the ENERGY LABEL supplied with the dishwasher:

- Annual energy consumptionis based on280 standard wash cycles with cold

water and consumption of low-energy operating modes. Actual consumption

depends on the way in which the appliance is used.

- Water consumption is based on 280 standard wash cycles. Actual

consumption depends on the way in which the appliance is used.

- Information refers to the EN 50242 STANDARD programme (identified in the

programmes table), which is the most effective in terms of combined energy

and water consumption. The programme is recommended for dishes with a

normal level of dirt.

- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”

(maximum efficiency).

User instructions

1.2 Washing programs

Before starting a washing program make sure that:

The water supply tap is open.

The correct amount of detergent has been added to the

dispenser.

The baskets have been correctly loaded.

The spray arms are able to rotate freely and without

obstruction.

The dishwasher door is securely closed.

Warning:

during the initial phase of the washing program, the operation of sprayers

is not perceived because they start rotating about 5 minutes after the start.

This is the normal operation of the washing cycle.

QUICK TIME PROGRAMS

Select this option together with any washing program (except the soak program) to

SHORTEN the cycle by from a minimum of 10% to a maximum of 55%, depending

on the cycle selected. To activate this option, press the QUICK OPTION button

(light comes on) after selecting the program required. The option is automatically

deactivated at the end of the program.

ENERSAVE

This option allows the further reduction of energy consumption, thanks

to the assisted drying when the door opens at the end of the cycle. At the

end of the wash, a device automatically releases the door, which slowly

opens a fewcentimeters. This allows the best drying possible, even at low

rinse temperature, permitting an important energy saving.

When the door is completely open, a brief sound signal indicates that the

wash cycle has ended.

Enersave is automatically activated in all programs that include a final

drying phase (seeprogram table). It is possible to disableit before starting

the program.

If this function is active, never prevent the door from opening by any

means, clear the space necessary to allow the opening of the door. Do

not force the closure of the door beforethe end of cyclesignal, because

this would damage the mechanism.

User instructions

SPREAD HALF LOAD

Suitable when there are not many dishes to be washed, it saves energy

andreduces theprogram duration. Place dishes inbothbaskets then load

the detergent dispenser than less than the normal amount for a full load.

EXTRA OPTIONS

“Flexi Tabs

” BUTTON

Press buttons 6 + 8 (QUICK TIME PROGRAMS button + ENERSAVE

option button) simultaneously to activate the "Flexi Tabs" option; the

respective light comes on to confirm the selection. The option is optimised

for use of detergents which are complete with salt and rinse aid, known

on the market as "3 in 1", "triple action", etc. With this option activated,

any salt and rinse aid If you wish to use detergents which already contain

salt and rinse aid already in the dishwasher will not be used.

N.B.: even with the " Flexi Tabs " option selected, the regenerating

salt/rinse aid lights will still stay on if their containers are empty.

IMPORTANT: the option continues to be active until it is deactivated by

pressing buttons 6 + 8 simultaneously; the light will then go out.

If the water hardness has been set on a value

above

, and the “

Flexi

Tabs” option is activated, the relative light flashes, warning of a setting

error. Multi-function products are not suitable for use with very "hard"

water; this does not prevent the useof the option, butthe washing results

might not be of the best.

DELAYED START

Thestartof the washingprogram can be delayedtoprogram thedishwasher

to operate at the preferred time of day (e.g. overnight). Press the

PROGRAM DELAY button to activate the option and display a 1 hour

delay. Keep pressingtoselect the delayrequired, which maybe up to 9, 12

or 24 hours depending on the model.

When the door is closed, the appliance will prewash the dishes, after

which the "program delay" set will come into effect.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smeg Spülmaschine Handbücher

Smeg

Smeg DWA6214S Bedienungsanleitung

Smeg

Smeg DD612SC Bedienungsanleitung

Smeg

Smeg PL19K Bedienungsanleitung

Smeg

Smeg DI6014 Bedienungsanleitung

Smeg

Smeg PL7233TX Bedienungsanleitung

Smeg

Smeg PL212 Bedienungsanleitung

Smeg

Smeg PL6545XD Bedienungsanleitung

Smeg

Smeg LSE50.1EB Bedienungsanleitung

Smeg

Smeg Dishwasher Bedienungsanleitung

Smeg

Smeg Universale DWA4510X Bedienungsanleitung

Smeg

Smeg PL8210X-1 Bedienungsanleitung

Smeg

Smeg Dishwasher DI612CAH Bedienungsanleitung

Smeg

Smeg Dishwasher KEX705 Service-Handbuch

Smeg

Smeg STFABCR3 Bedienungsanleitung

Smeg

Smeg IGE3980 Bedienungsanleitung

Smeg

Smeg STO900 Bedienungsanleitung

Smeg

Smeg PL8605X8 Bedienungsanleitung

Smeg

Smeg ST4523IN Bedienungsanleitung

Smeg

Smeg LS647XNL2 Bedienungsanleitung

Smeg

Smeg ST1146SE Bedienungsanleitung

Smeg

Smeg DWI614 Bedienungsanleitung

Smeg

Smeg DF6FABAZ1 Bedienungsanleitung

Smeg

Smeg DI612A1 Bedienungsanleitung

Smeg

Smeg LSE451 Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

KitchenAid

KitchenAid KUDB230B Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung