Smeg Universale PL65233XIN Bedienungsanleitung

Contents

1. Description of the controls _______________________________ 2

2. Operating instructions __________________________________ 10

3. Cleaning and maintenance ______________________________ 27

4. Troubleshooting ______________________________________ 33

Thank you for choosing one of our products.

You are advised to read this manual carefully; it contains all the

information you need to use your dishwasher safely, correctly and in the

most satisfactory manner.

Following the cleaning instructions provided here will keep your

dishwasher's performance at peak levels in the long term.

USER INSTRUCTIONS: these consist of recommendations for using the

appliance, a description of its controls and of the correct cleaning and

maintenance procedures.

User instructions

1. Description of the controls

1.1 Front panel

All the dishwasher controls are grouped on the front panel. Programming

and option selection are only possible with the door closed.

1 ON/OFF BUTTON AND WARNING LIGHT

2 OPTION SELECTION BUTTONS AND WARNING LIGHTS

3 “CHILD LOCK” ACTIVATION BUTTONS

4 NO RINSE AID LIGHT (some models only)

5 SALT WARNIN LIGHT (on some models only)

6 PROGRAM SELECTION BUTTONS

7 START/PAUSE BUTTON

8 PROGRAM INDICATOR LIGHTS

9 HANDLE TO OPEN THE DOOR

N.B.: symbols and styling are guideline and may vary depending on

the model or version of the dishwasher purchased.

User instructions

PROGRAMS TABLE

PROGRAMME

NUMBER

& SYMBOL

LOAD CROCKERY AND

CUTLERY

PROGRAM

PROGRESS

DURATION

CONSUMPTION

MINUTES

(1)

WATER

LITRES

POWER

KWh (1)

1 SOAK

Recommended for rinsing

dishes while waiting for

another wash cycle.

Cold prewash 15 3,5 0,02

2 ½ LOAD

****

Recommended if you

have to wash just a few

normally soiled dishes,

washed immediately after

use

Wash at 65°C

Cold rinse

Rinse at 70°C

Dry

11 1,20

3 (*)

EN 50242

Wash cycle with lower

water and energy

consumption,

recommended for

washing normally soiled

dishes, even with dried-on

residues.

Cold prewash

Wash at 45°C

Rinse at 55°C

Dry

D **

** **

4 MIX 65°

IEC/DIN***

Wash cycle for normally

soiled mixed loads such

as dishes and pans, even

with dried-on residues.

Cold prewash

Wash at 65°C

Rinse at 70°C

Dry

13,5 1,35

5 INTENSE 70°

****

Program suitable for

heavily soiled plates, pots

and pans, even with

dried-on residues.

Hot prewash

Wash at 70°C

Cold rinse (2)

Rinse at 70°C

Dry

130

15,5 1,60

IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.

If the dishwasher door is open or not properly closed, the washing cycle

will not start.

DRY

ASSIST Only at the end of the Eco program will Dry assist be activated.

User instructions

NOTES AND REFERENCES

Only run the soak program with half loads.

Options cannot be used with the soak program.

* Standard programme under

EN 50242

** See information sheet provided

***

IEC/DIN

reference programme.

**** Reference program for laboratories: Detergent: 20g in the dispenser + 10g in

the

door

or tablet.

Configuration

: see photo in “Using the baskets”.

(1) Program consumption and duration figures have been measured in accordance

with the EN 50242 standard. Values may vary depending on intake water and

room temperatures and the type and quantity of dishes loaded.

(2) 1 or 2 cold rinses depending on the model.

REFERENCES for the ENERGY LABEL supplied with the dishwasher:

- Annual energy consumption is based on 280 standard wash cycles with cold

water and consumption of low-energy operating modes. Actual consumption

depends on the way in which the appliance is used.

- Water consumption is based on 280 standard wash cycles. Actual

consumption depends on the way in which the appliance is used.

- Information refers to the EN 50242 STANDARD programme (identified in the

programmes table), which is the most effective in terms of combined energy

and water consumption. The programme is recommended for dishes with a

normal level of dirt.

- Drying efficiency class on a scale from “G” (minimum efficiency) to “A”

(maximum efficiency).

Notice for testing institutes

Testing institutes are provided with guidelines for

comparative tests (e.g. according to EN60436).

If the form for the testing institutes is missing from

the documentation, please request the guidelines

by contacting us at the following e-mail address:

[email protected]

When making a request, please specify the model

(MOD) and the serial number (S/N) indicated on the

plate on the side of the door.

User instructions

1.2 Washing programs

The dishwasher is equipped with a control panel and an INFORMATION

DISPLAY from which it is possible to carry out all the power switch-on,

switch-off and programming operations.

Before starting a washing program make sure that:

 The water supply tap is open.

 The correct amount of detergent has been added to the

dispenser.

 The baskets have been correctly loaded.

 The spray arms are able to rotate freely and without

obstruction.

 The dishwasher door is securely closed.

Warning:

during the initial phase of the washing program, the operation of sprayers

is not perceived because they start rotating about 5 minutes after the start.

This is the normal operation of the washing cycle.

SWITCHING ON

When the ON/OFF button (1) is pressed, the dishwasher switches on.

The indicator lights will display the dishwasher's "status".

PROGRAMMING

Programming operations are only possible with the door closed.

As long as the door is open, the

PROGRAMS (

)

lights remain off.

PROGRAM SELECTION

Press the PROGRAM SELECTION button (6) several times until the light of

the program required comes on.

User instructions

DRY ASSIST

If there is a “D” in the “DURATION” column of the programs table, the door

opens automatically at the end of the cycle. This allows the dishes to be

dried perfectly even at low rinse temperatures, and therefore significant

energy savings. The door opens slowly by a few centimetres at the end of

the wash cycle. The dishwasher remains inactive between the final rinse

and the end of the cycle to allow the load to be properly dried. The program

is interrupted if the door is opened during this stage. A short beep is

emitted and cycle lights 4 and 5 flash to indicate that the cycle has

finished.

There must be sufficient space available for the door to open. The

door must not be forced open and closed before the wash cycle has

ended.

STARTING THE PROGRAM

To start the dishwasher, press the START/PAUSE button (6) for a few

seconds, until the light of the selected program starts to flash (confirmation

beep).

The light will flash as long as the program is in progress, to indicate that it

is being performed.

END OF PROGRAM

At the end of the program the beeper sounds briefly and

the program

lights

and

(marked "end") flash.

INTERRUPTION A PROGRAM

To interrupt a program in progress:

 press the START/PAUSE button (6); the light of the program in

progress remains on (confirmation beep);

 you may now restart the program by pressing button (6) again until it

restarts, or change or annul the program (see "CHANGING A PROGRAM",

or "

NNULLING A PROGRAM").

User instructions

CHANGING A PROGRAM

To change the running program it is necessary:

 to interrupt the running program (see “INTERRUPTION A PROGRAM”);

 select the new program;

 start the program (see “

TARTING THE PROGRAM”).

ANNULLING A PROGRAM

To annul the program, keep the START/PAUSE button (7) pressed until

the program is interrupted (light on and confirmation beep).

Press button (7) again and keep it pressed until the

lights

and

(marked "end") come on.

The water in the tank will be pumped out and the program will end at the

point where it was interrupted.

In case that the door is opened during the operation, to the next door

closing it is going to be necessary to start the program as shown in

paragraph “STARTING THE PROGRAM”. The program will resume from the

point in which it was interrupted.

In case that the tub temperature is higher than 50°C the program will

start about 60 seconds later.

User instructions

OPTION SELECTION

Options are selected by pressing the relative button

by the symbol of the option required; the light

comes on to confirm that the option has been

activated.

 It is not possible to select any options when the soak program is being

used.

 All options except "Flexi Tabs" are disabled at the end of the wash cycle.

To disable the “Flexi Tabs” option, press the relative button (the light goes

out).

 All options, including "Flexi Tabs" are disabled when a program is

CANCELLED

after it has begun.

PROGRAM DELAY

Allows you to program the dishwasher cycle to start during the required

time period (e.g. night). Press the DELAY button to delay the start for up

to 3, 6, 9 hours. To cancel the setting, press the button several times until

the lights switch off. The option cannot be selected once the cycle is

running. After the door has been closed, the dishwasher will carry out a

pre-wash cycle, after which the set “cycle delay” option will be activated.

EXTRA DRY

Adds a hot rinse cycle that ensures improved drying. Suitable for loads that

contain dishes that are difficult to dry such as pots, non-stick pans and

plastic containers.

“CHILD LOCK” OPTION

By pressing the indicated buttons at the same time, the controls are

locked, which is confirmed when the warning light on display turns on. This

option stays active until the buttons are pressed again.

User instructions

TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT

 Always try to run the dishwasher fully loaded.

 Do not wash the dishes in running water.

 Use the washing program that is most appropriate for each type of

load.

 Do not carry out any preliminary rinsing.

 If available, connect the dishwasher to a hot water supply up to 60°C.

TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT

THE ENVIRONMENT

The phosphates contained in dishwasher detergents are harmful to the

environment. To avoid using excessive amounts of detergent and to save

on electricity, observe the following:

 separate the more delicate items from dishes that are more resistant

to aggressive detergents and high temperatures;

 do not pour the detergent directly on the dishes.

ENERGY MANAGEMENT

At the end of the program the warning lights of programs no. 4 and 5

flash for 5 minutes; afterwards, the washing machine switches off

automatically in order to reduce standby power consumption.

In order to switch it on again, it is necessary to press the ON/OFF button.

REMOVING THE DISHES

At the end of the washing program, wait at least 20 minutes before

removing the dishes, to allow them to cool down. To prevent any water

droplets on the upper basket from falling on the dishes in the lower basket,

it is

advisable

to unload the lower basket first, and then the upper basket.

User instructions

2. Operating instructions

Once the dishwasher has been correctly installed, prepare for use as

follows:

 Adjust the water softening system;

 Add the regenerating salt;

 Add the rinse aid and detergent.

2.1 Using the water softening system

The amount of scale contained in the water

(water hardness index) can cause whitish

staining on the dry dishes, which tend to

become dull over time. The dishwasher is

equipped with an automatic softening

system which uses a special regenerating

salt to reduce the hardness of the water.

The dishwasher is factory set for water

hardness level 3 (average hardness ).

When using water of medium hardness, the regenerating salt container

should be refilled after approximately 20 washing cycles. The salt

container can hold approximately 1 Kg of salt in grains. The container is

situated at the bottom of the dishwasher. After removing the lower basket,

unscrew the salt container cap by turning it anticlockwise and pour in the

salt using the funnel supplied with the dishwasher. Before replacing the

cap, remove any salt residues from around the opening.

 When using the dishwasher for the first time, in addition to the salt it

is also necessary to add one litre of water to the container.

 Each time the salt container is refilled, make sure that the cap is

securely closed. The mixture of water and detergent must never

penetrate the salt container, as this would compromise the operation

of the regeneration system. In the event of this occurring, the warranty

will be invalidated.

 Only use regenerating salt specially formulated for domestic

dishwashers. If using salt tablets, do not fill the container

completely.

SALT

Inhaltsverzeichnis

Andere Smeg Spülmaschine Handbücher

Smeg

Smeg STFABUWH Bedienungsanleitung

Smeg

Smeg 3LBA500 Bedienungsanleitung

Smeg

Smeg CSE66B Bedienungsanleitung

Smeg

Smeg CW510 Bedienungsanleitung

Smeg

Smeg Dishwasher DWD64.1BL Bedienungsanleitung

Smeg

Smeg CA01-4 Leitfaden

Smeg

Smeg GM287-110 Bedienungsanleitung

Smeg

Smeg PL5222B Bedienungsanleitung

Smeg

Smeg DWA214W Bedienungsanleitung

Smeg

Smeg DWD64.1SS Bedienungsanleitung

Smeg

Smeg STC75 Bedienungsanleitung

Smeg

Smeg DWAI152XT Bedienungsanleitung

Smeg

Smeg PL6545XD Bedienungsanleitung

Smeg

Smeg STA6245-9 Bedienungsanleitung

Smeg

Smeg A445XA Betriebsanleitung

Smeg

Smeg DI612CA Bedienungsanleitung

Smeg

Smeg PL19K Bedienungsanleitung

Smeg

Smeg DF410BL Bedienungsanleitung

Smeg

Smeg GM274-110 Betriebsanleitung

Smeg

Smeg PL614WH-1 Bedienungsanleitung

Smeg

Smeg DWAFI4510-2 Bedienungsanleitung

Smeg

Smeg DI614H Bedienungsanleitung

Smeg

Smeg DF13FAB3CR Bedienungsanleitung

Smeg

Smeg ST1146SE Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

KitchenAid

KitchenAid KUDB230B Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung