Smeg CS20-6 Bedienungsanleitung

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 38

2. INSTALLING THE APPLIANCE _____________________________ 40

3. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 43

4. FINAL OPERATIONS_____________________________________ 45

5. DESCRIPTION OF CONTROLS ____________________________ 47

6. USING THE COOKING HOB _______________________________ 53

7. USING THE OVENS______________________________________ 55

8. AVAILABLE ACCESSORIES _______________________________ 57

9. COOKING ADVICE ______________________________________ 58

10. CLEANING AND MAINTENANCE ___________________________ 65

11. EXTRAORDINARY MAINTENANCE _________________________ 69

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE

IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified

technician who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the controls and the correct procedures for cleaning and

maintenance of the appliance.

Further information about the products can be found at

www.smeg.com

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE

READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE

USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN

ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS

INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT

REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY

OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.

ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN

THOSE STATED ABOVE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE

THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST

SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET

MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT

REGULATIONS.

THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN

BUILT IN.

NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.

SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE

SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

(OFF) WHEN YOU FINISH USING THE HOB.

NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: THEY COULD BE

ACCIDENTALLY LIGHTED AND CAUSE FIRES.

Introduction

THE IDENTIFICATION PLATE WITH THE TECHNICAL DATA, SERIAL

NUMBER AND BRAND NAME IS IN A VISIBLE POSITION INSIDE THE

STORAGE COMPARTMENT.

DO NOT REMOVE THIS PLATE FOR ANY REASON.

DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM.

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS

ON THE COOKING HOB PAN STANDS.

DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE

OUTER PERIMETER OF THE HOB.

THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING

CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN

EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY

ARE SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE

RESPONSIBLE FOR THEIR SAFETY.

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE

2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

(WEEE).

THIS DIRECTIVE DETERMINES THE STANDARDS FOR THE COLLECTION

AND RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

APPLICABLE THROUGHOUT THE EUROPEAN UNION.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer cannot be held liable for damage to persons or

things caused by failure to comply with the above requirements or by

tampering with any part of the appliance or by the use of non-original

spare parts.

Instructions for the installer

2. INSTALLING THE APPLIANCE

It is the law that all gas appliances are installed by competent persons.

Corgi gas installers are approved to work to safe and satisfactory

standards. All gas installation, servicing and repair work must be in

accordance with the gas safety regulations 1984 (installation and use) as

amended 1990.

It may be installed against walls one of which is higher than the worktop

surface, at least 50 mm from the side of the appliance, as shown in the

installation class drawings A and B. Wall units or extractor hoods installed

above the appliance's work-top must be at least 750 mm above it.

A B

Built-in appliance Free-standing installation

2.1 Electrical connection

Make sure the voltage and the cross-section of the power supply line

match the specifications indicated on the identification plate positioned in

the storage compartment.

Do not remove this plate for any reason.

The plug at the end of the power cable and the wall socket must be the

same type (conforming to regulations in force). Check that the power line

is adequately grounded. Do not use reducers, adapters or shunts.

If the appliance is connected to the power grid using a fixed connection,

fit the power supply line with a multipolar cut-out device with a contact

opening gap equal to or greater than 3 mm in an easily accessible

position close to the appliance.

Instructions for the installer

For operation on 380-415V3N

∼

:use a

H05RR-F-type five-core cable (5 x 1.5 mm2).

For operation on 380-415V2N

∼

:use a

H05RR-F-type four-core cable (4 x 1.5 mm2).

For operation on 220-240V

∼

:use a H05RR-

F-type three-core cable (3 x 2.5 mm2).

The cable end to be connected to the

appliance must be provided with an ground

wire (yellow-green) at least 20 mm longer.

The manufacturer cannot be held liable for damage to persons or

things caused by failure to comply with the above requirements or by

tampering with any part of the appliance.

2.2 Ventilation requirements

The room containing the appliance should have an air supply in accordance

with B.S. 5440 part 2 1989.

1. All rooms require an opening window or equivalent, and some rooms will

require a permanent vent as well.

2. For room volumes up to 5 m3an air vent of 100 cm2is required.

3. If the room has a door that opens directly to the outside, and the room

exceeds 1 m3no air vent is required.

4. For room volumes between 5 m3and 10 m3an air vent of 50 cm2is

required.

5. If there are other fuel burning appliances in the same room B.S. 5440

part 2 1989 should be consulted to determine the air vent requirements.

6. This appliance must not be installed in a sitting room of less than 20 m3

or in a bathroom or shower room.

Windows and permanent vents should therefore not be blocked or removed

without first consulting a Corgi gas installer.

Failure to install appliances correctly is dangerous and could lead to

prosecution.

Instructions for the installer

2.3 Connecting to natural and LPG gas (Please see

connection diagram)

Make the connection to the appliance using flexible bayonet

style hose in accordance to B.S. 669. The hose connection at

the rear of the appliance has a 1/2" BSP internal thread.

Please use seal Cbetween the flexible connection Land the

appliance supply tube B. When making the connection, make

sure that no stress of any kind is applied to the cooker and

that the hose does not touch any sharp edges.

If connecting to LPG the bayonet hose must have red

bands on it.

2.4 Instruction for wall fixing (only on some models)

1) Fix the screw to the wall and hook the chain (B);

2) Hook the chain to the hole positioned at the rear of the cooker by the gas

pipe (A);

3) Once the chain is in position, push the cooker against the wall;

4) The height of the screw hole from floor level must not exceed 800 mm (C).

Instructions for the installer

3. ADAPTATION TO DIFFERENT TYPES OF GAS

Before carrying out the following operations, disconnect the appliance

from the electricity supply

The cooker hob is preset for natural gas G20 (2H) at a pressure of 20

mbar. In the case of functioning with other types of gas the burner

nozzles must be changed and the minimum flame adjusted on the gas

taps. To change the nozzles, proceed as described below.

3.1 Replacement of nozzles on the hob

This operation requires no primary air regulation.

1. Extract the pan stands and remove all the caps and flame-spreader

crowns;

2. Unscrew the burner nozzles with a 7 mm socket wrench;

3. Replace the nozzles according to the type of gas to be used and the

description in paragraph “3.2 Burner and nozzle characteristics

table”.

Replace the burners in the correct position.

Instructions for the installer

3.2 Burner and nozzle characteristics table

Burner

Rated

heating

capacity

(kW)

LPG –G30/G31 28/37 mbar

Nozzle

diameter

1/100 mm

Reduced

capacity

(W)

Capacity

g/h G30

Capacity

g/h G31

Auxiliary 1.05 50 400 76 75

Semi rapid 1.8 65 500 131 129

Rapid 3.0 85 800 218 214

Ultra rapid 3.9 100 1600 284 279

Burner

Rated

heating

capacity

(kW)

Natural gas – G20 20 mbar

Nozzle

diameter

1/100 mm

Reduced

capacity

(W)

Auxiliary 1.05 72 400

Semi rapid 1.8 97 500

Rapid 3.0 115 800

Ultra rapid 3.9 135 1600

3.3 Arrangement of burners on cooking hob

BURNERS

1Auxiliary

2Semi rapid

3Rapid

4Ultra rapid

5Ultra rapid

Instructions for the installer

4. FINAL OPERATIONS

After replacing the nozzles, reposition the flame-spreader crowns, the

burner caps and the pan stands.

After adjustment to a different kind of gas from the one for which the

cooker has been tested, replace the plate inside the storage

compartment with one corresponding to the new kind of gas. This plate

can be obtained from your nearest Authorised Assistance Centre.

4.1 Adjustment of minimum for natural gas

Light the burner and take it to the minimum .

Remove the gas tap knob and turn the

adjustment screw inside or at the side of the tap

shaft (depending on the model) until there is a

regular minimum flame. Replace the knob and

check burner flame stability: (rapidly turning the

knob from maximum to minimum position, the

flame should not go out). Repeat the operation on

all the gas taps.

4.2 Adjustment of minimum for LPG

To adjust the minimum for LPG, completely tighten (clockwise) the screw

inside or next to the gas tap pin (depending on the model).

The diameters of the by-passes for each burner are given in table “3.2

Burner and nozzle characteristics table”.

4.3 Positioning and levelling of the appliance

Having carried out the electricity and gas hook-up, level the appliance

using the four adjustable legs.

Instructions for the installer

4.4 Mounting the skirt

•Position the skirt above the top, taking care to align holes Awith

holes B.

•Secure the skirt to the top by tightening screws C.

Inhaltsverzeichnis

Andere Smeg Reichweite Handbücher

Smeg

Smeg A1.1K Bedienungsanleitung

Smeg

Smeg CSP20-6 Bedienungsanleitung

Smeg

Smeg CS150-6 Bedienungsanleitung

Smeg

Smeg SSA60MFX Bedienungsanleitung

Smeg

Smeg APC61BVG Bedienungsanleitung

Smeg

Smeg SUK91MFX9 Bedienungsanleitung

Smeg

Smeg TRU90X Bedienungsanleitung

Smeg

Smeg C30GGXU Bedienungsanleitung

Smeg

Smeg C6GVXI Bedienungsanleitung

Smeg

Smeg CE6GPXU Bedienungsanleitung

Smeg

Smeg CPF36UGGX Bedienungsanleitung

Smeg

Smeg SNLK916MFN9 Bedienungsanleitung

Smeg

Smeg COS905GX Bedienungsanleitung

Smeg

Smeg TRU36GMWH Bedienungsanleitung

Smeg

Smeg A5-6 Bedienungsanleitung

Smeg

Smeg SPR36UGMX Bedienungsanleitung

Smeg

Smeg CPF48UGMYW Bedienungsanleitung

Smeg

Smeg Freestanding Gas Range C6GGXU Bedienungsanleitung

Smeg

Smeg A11XPY-9 Bedienungsanleitung

Smeg

Smeg C24GGXU Bedienungsanleitung

Smeg

Smeg CS120-6 Bedienungsanleitung

Smeg

Smeg SSA60MX8 Bedienungsanleitung

Smeg

Smeg CX68CM8 Bedienungsanleitung

Smeg

Smeg C9GMXA Bedienungsanleitung

Beliebte Reichweite Handbücher anderer Marken

Samsung

Samsung FCQ321HTUW Bedienungsanleitung

Kenmore

Kenmore 790.45712 Bedienungsanleitung

Wolf

Wolf CHR CHSSR Bedienungsanleitung

Zanussi

Zanussi ZCG054G Bedienungsanleitung

Whirlpool

Whirlpool 8575985-W Stücklistenhandbuch

Frigidaire

Frigidaire 316000635 Bedienungsanleitung

GE JCSS630 Bedienungsanleitung

Samsung

Samsung NX58M9960P series Bedienungsanleitung

Hotpoint

Hotpoint RB524R Installationsanleitung

Whirlpool

Whirlpool Roper FGP305KW3 Bedienungsanleitung

Amana

Amana ART6610 SERIES Bedienungsanleitung

Maytag

Maytag MERH770WB Bedienungsanleitung

Fulgor Milano

Fulgor Milano SOFIA Bedienungsanleitung

Premier

Premier EF-4358GH Bedienungsanleitung

Kenmore

Kenmore 790.9010 Series Bedienungsanleitung

KitchenAid

KitchenAid KESC300 Bedienungsanleitung

Frigidaire

Frigidaire FFEF3012LS Benutzerhandbuch

Diamond

Diamond G65/2F4T Bedienungsanleitung