Smeg Fridge-freezer Bedienungsanleitung

GB Instructions for use

Refrigerator-freezer

260437

We thank you for the conﬁdence you have shown by purchasing our appliance.

We wish you a lot of pleasure using the appliance.

The refrigerator-freezer (hereinafter referred to as the appliance) consists of two parts: the upper

part is the refrigerator compartment, and the lower part is the freezer compartment – freezer chest.

The refrigerator compartment is intended for use in households, for storing fresh food at

temperatures higher than 0°C.

The freezer is intended for use in households, for freezing fresh food and for long-term storage of

frozen food (up to one year, depending on the type of food).

Important warnings ..................................................... 3

A few tips on how to save power with your

refrigerator-freezer combo ........................................ 4

Appliance description................................................. 5

Installation and connection........................................ 7

Changing the door opening direction ....................... 9

Operating the appliance with

electronic controls .................................................... 11

Operating the mechanically

controlled appliance ................................................. 17

Recommended food arrangement

in the appliance ......................................................... 23

Storing food in the refrigerator ................................ 24

Storage of food in the FreshZone............................ 25

Freezing fresh food and storing frozen food.......... 26

Defrosting the appliance........................................... 28

Cleaning the appliance ............................................. 29

Troubleshooting ........................................................ 30

Information on appliance noise ............................... 32

260437

• This appliance is manufactured in compliance with relevant

safety standards. However, it is still advisable it is not used

without due supervision by persons with diminished physical,

motoric, or mental capabilities or persons with inadequate

experience or knowledge. The same recommendation applies

to minors using the appliance.

• Before connecting the appliance, carefully read the

instructions for use which describe the appliance and its

correct and safe use. The instructions apply to several types

/ models; therefore, they may include descriptions of settings

and equipment that may not be available in your refrigerator.

The instructions also apply to the NO FROST version of the

freezer, featuring a built-in fan and automatic defrosting.

• Remove the packaging that is intended for protecting the

appliance or its respective parts during transport.

• Spacers are ﬁtted in the corners of the doors; these should

be removed and the plugs attached (only with some models)

should be inserted into the openings.

• Before connecting to the power mains, the appliance should

be left to stand still in upright position for at least 2 hours.

Thus, operation errors due to the effect of transport on the

cooling system will be much less likely to occur.

• The appliance must be connected to the power mains and

grounded in compliance with the effective standards and

regulations.

• The appliance may not be used outdoors and should not be

exposed to rain.

• The appliance must be disconnected from the power mains

(unplug the power cord from the wall outlet) before cleaning or

before replacing the bulb.

• If the power cord is damaged, it should be replaced by a

service technician or other authorized person.

• If the appliance is not used for a longer period of time, switch

it off with the relevant button and disconnect it from the power

mains. Empty the appliance, defrost it, clean it, and leave the

door ajar.

• To protect the environment, dispose of the appliance after its

useful life by taking it to an authorized waste collection center.

• The packaging is made of environment-friendly materials that

can be recycled, disposed of, or destroyed without hazard to

the environment.

• Children should not play with the appliance.

• The label with basic information on the appliance is attached in

the appliance interior. If the label is not in your local language,

replace it with the one supplied with the appliance.

Important warnings

260437

• Warning! Ventilation slots on the appliance or a built-in element must always be clean and

unobstructed.

• Warning! Do not use mechanical devices or tools to defrost the refrigerator, nor any other

methods except for those recommended by the manufacturer.

• Warning! When installing, cleaning, or removing the appliance, make sure the insulation on the

refrigeration system parts is not damaged. Thus you will also prevent damage to the environment.

• Warning! Do not use electric appliances in the refrigerator or freezer interior, except for those

expressly allowed by the refrigerator-freezer manufacturer.

The symbol on the product or on its packaging indicates that this product may not be

treated as household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of thisproduct. For more detailed information about recycling

of this product, please contact your local city ofﬁce, your household waste disposal service

or the shop where you purchased the product.

• Observe the installation instructions.

• Do not open the appliance door more frequently than necessary.

• Occasionally check whether air can circulate freely behind the appliance.

• Condenser unit mounted on the appliance back wall must be kept clean at all times (see section

“Cleaning the appliance”).

• If the seal is damaged or loose, replace it as soon as possible.

• Store your food in closed containers or other appropriate packaging.

• Before placing the food in the refrigerator, let it cool down to room temperature.

• Defrost your frozen food in the refrigerator compartment.

• Remove the freezer drawers and door as described in the instructions, in order to make use of

the entire capacity.

• Defrost your conventional freezer when a frost layer approximately 3-5 millimetres thick has

accumulated on the surfaces in the freezer compartment.

• Make sure the shelves are evenly distributed and that the food is arranged in a way that

allows free circulation of air (heed the recommended food arrangement as described in the

instructions).

• In appliances ﬁtted with a fan, do not block the fan slots.

A few tips on how to save power with your

refrigerator-freezer combo

260437

• Appliance interior equipment may change subject to appliance model.

• The drawers are protected against pulling out. If you wish to remove a drawer, pull it out as far as

it will go, then lift its front part and pull it out completely.

* Only with some models.

A Refrigerator compartment

1Control unit

2Interior illumination lamp

3Shelf (height adjustable)

4Fruit and vegetables

bin / drawer

5Refrigerator door rack (deep

and shallow version)

6Bottle rack

B Standard freezer

(standard appliances)

7 Freezing drawer

8Storage drawer

9Storage drawer

10 Freezer door rack*

11 Water discharge groove*

12 Foot*

13 Wheel*

B NO FROST freezer

7Storage drawer

8 Freezing drawer

9 Storage drawer

Appliance description

260437

• Appliance interior equipment may change subject to appliance model.

• The drawers are protected against pulling out. If you wish to remove a drawer, pull it out as far as

it will go, then lift its front part and pull it out completely.

* Only with some models.

A Refrigerator compartment

1Control unit

2Interior illumination lamp

3Shelf (height adjustable)

4Fruit and vegetables

bin / drawer

5Refrigerator door rack (deep

and shallow version)

6Bottle rack

B Standard freezer

(standard appliances)

7 Freezing drawer

8Storage drawer

9Storage drawer

10 Freezer door rack*

11 Water discharge groove*

12 Foot*

13 Wheel*

B NO FROST freezer

7Storage drawer

8 Freezing drawer

9 Storage drawer

260437

• The appliance should be installed in a dry and well ventilated

room. The appliance will operate correctly if the environment

temperature is within the ranges listed in the table below.

The appliance class is indicated on the label with the basic

information on the appliance.

Class Temperature

SN (subnormal) from +10°C to +32°C

N (normal) from +16°C to +32°C

ST (subtropical) from +16°C to +38°C

T (tropical) from +16°C to +43°C

Appliance installation should be carried out by at least two

persons to avoid any physical injury or damage to the appliance.

• The appliance should stand ﬁrmly in an upright position on a

sufﬁciently solid base. At the front, the appliance is ﬁtted with

two adjustable legs that can be used to level the appliance

(only with some models). Rear side of the appliance is ﬁtted

with wheels (certain models only) facilitating the positioning of

the appliance at the preselected place.

• If there is a kitchen furniture element above the appliance,

there should be a clearance of at least 5 centimeters between

this element and the refrigerator, to ensure sufﬁcient cooling of

the condenser unit.

• Two spacers attached to the appliance must be ﬁtted onto the

upper edge of the condenser, thus preventing the appliance

from being installed too close to the wall (only some models

have it). Spacers are manufactured for all-purpose function

depending on the distance of the condenser from the

appliance. Therefore turn spacers correspondingly and ﬁx

them to the appliance.

• Do not expose the appliance to direct sunlight and do not

place it near sources of heat. If this cannot be avoided, install

an insulation panel.

• Handles are ﬁtted under the housing at the front side to

make moving the appliance easier (only with some models).

The appliance may stand freely or it can be placed next to a

kitchen furniture element or a wall. Mind the space required

to open the door and pull out the drawers and shelves (see

installation diagram).

Selecting the room

Installing the appliance

Installation and connection

260437

Remark:

* Applies to OLD TIMER appliances.

• Use the power cord to connect the appliance to the power

mains. The wall outlet should be ﬁtted with a ground contact

(safety socket). Nominal voltage and frequency are indicated

on the label with basic information on the appliance.

• The appliance should be connected to the power mains and

grounded in compliance with the relevant effective standards

and regulations.

The appliance will withstand short-term deviations from the

nominal voltages, but not more than from -6 % to +6%.

Connecting the

appliance

260437

Tools required: ring spanner (box-end wrench) No. 8, screwdriver, torx25, ﬂathead

screwdriver

1. Use a ﬂathead screwdriver to remove the hole plugs/covers A and B1.

2. Unscrew and remove – one by one, in the speciﬁed order from top to bottom – the hinges (C, D,

and E1) and the door (F, G). Make sure the door is not damaged.

3. Move the hole plugs / covers (H) to the opposite side.

4. Attach the lower hinge (E2, supplied in a bag) to the opposite side of the housing and add the

washer (I).

5. Upper door (F): Move the upper hinge (C) with the bearing (J) to the opposite side. Remove the

door stopper with the hinge (K1) and attach a symmetrical door stopper (K2, supplied in a bag)

to the opposite side.

6. Lower door (G): move the hinges (L) and the cover (M) to the opposite side.

7. Install / attach, from bottom up, the hinges (D, C) and doors (G, F). Do not forget to install the

washers in the same way they were installed before disassembling (I).

8. Install the covers A and B2 (cover B2 from the supplied bag).

9. Replacing the handle: remove the hole plugs/covers, unscrew the screws and attach the

handle to the opposite side. Insert the plugs into the holes on the opposite side.

Save the elements B1, E1, and K1 in case you need them to change the door opening

direction again at a later time.

Changing the door opening direction

Version I

260437

Required tools: socket spanner nr. 8, screwdriver, torx 25.

Caution! After unscrewing of before ﬁxing hinges, hold the door

to prevent it from falling and damaging.

1. Remove upper hinge cover (save it for eventual later use),

remove also the cover on the opposite side of the upper hinge

cover (on the opposite side you will insert the attached cover

during the assembly), and remove the cover on the opposite

side of the upper part of the door.

2. Unscrew upper hinge screws and remove the upper door from

the middle hinge.

3. On the bottom side of the upper door unscrew the swing

stopper screws and remove the stopper (A). Keep this for

eventual use later on. Fix the attached stopper with its

bearing on the opposite side of the door.

4. Unscrew the forced door closure system (B) and ﬁx it to the

opposite side of the door (certain models only).

5. Unscrew middle hinge screws, remove the door from bottom

hinge.

6. Loosen the screws ﬁxing the leg supports (certain models

only), then continue the procedure either under cf. 7 or 7.1,

depending on the model of the appliance.

7. Tilt the appliance backward (max. 35°) to lean to the rear

side of the cabinet. Unscrew the leg support screws (C) - left

and right, and remove the leg support cover (D) and place it

to the opposite side. Unscrew and remove, then reciprocally

replace the position of end switch (E) and decorative peg (F)

(for models with forced door closing system). Unscrew three

screws ﬁxing the bottom hinge (save the hinge for later use),

and ﬁx the attached bottom hinge on the opposite side.

7.1. Tilt the appliance backwards (max. 35°) to lean on the

housing at the back.

Loosen three screws holding the bottom hinge (save the

hinge for eventual subsequent door swing change). On the

opposite side afﬁx the attached bottom hinge. Plug the holes

left after the replacement with relevant pegs.

8. Repeat the procedure 3 and 4 on the bottom door. In case

there is no bottom door limit peg, transfer the bearing (G) and

washer to the opposite side of the door.

9. Proceed with the assembly procedure in opposite sequence.

Remark:

• At OLD TIMER appliances alteration of door opening direction

is not possible.

Version II

Changing the door

opening direction

Andere Handbücher für Fridge-freezer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Smeg Kühlschrank Handbücher

Smeg

Smeg S4L120F Bedienungsanleitung

Smeg

Smeg 914777947 Bedienungsanleitung

Smeg

Smeg C7280FPL Bedienungsanleitung

Smeg

Smeg FAB 32 Bedienungsanleitung

Smeg

Smeg American Style Fridge Freezer FA550XBI Bedienungsanleitung

Smeg

Smeg SBS63XDE Bedienungsanleitung

Smeg

Smeg FAB28MCUS Bedienungsanleitung

Smeg

Smeg S3C090P1 Bedienungsanleitung

Smeg

Smeg FA402PX Bedienungsanleitung

Smeg

Smeg FI281B Bedienungsanleitung

Smeg

Smeg FC20EN1W Konfigurationshandbuch

Smeg

Smeg FC370BP Bedienungsanleitung

Smeg

Smeg FCA375 Bedienungsanleitung

Smeg

Smeg CR324A7 Bedienungsanleitung

Smeg

Smeg FS08EW Bedienungsanleitung

Smeg

Smeg Refrigerator SRA416TP3 Schulungshandbuch

Smeg

Smeg FR138A Bedienungsanleitung

Smeg

Smeg CV 2902 PNE Bedienungsanleitung

Smeg

Smeg CB300U Bedienungsanleitung

Smeg

Smeg FA311X Bedienungsanleitung

Smeg

Smeg S41STRP Bedienungsanleitung

Smeg

Smeg FAB30QAZ Bedienungsanleitung

Smeg

Smeg FC344BNF Bedienungsanleitung

Smeg

Smeg FPD34AS Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung