SMSC EMC1428 Bedienungsanleitung

Insert EVB graphic/photo here

(this text can be removed on master page view)

SMSC EMC1428 Revision 1.0 (08-21-07)

The information contained herein is proprietary to SMSC, shall be used solely in accordance with the agreement pursuant to which it is provided,

and shall not be reproduced or disclosed to others without the prior written consent of SMSC. Although the information is believed to be accurate,

no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to this document and to specifications and product

descriptions at any time without notice. Neither the provision of this information nor the sale of the described semiconductor devices conveys any

licenses under any patent rights or other intellectual property rights of SMSC or others. The product may contain design defects or errors known as

anomalies, including but not necessarily limited to any which may be identified in this document, which may cause the product to deviate from pub-

lished specifications. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where

product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an

officer of SMSC will be fully at the risk of the customer. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”).

SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRAN-

TIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY

AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR

ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS

OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF

SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS

HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

EMC1428 EVB User Manual

Revision 1.0 (08-21-07) SMSC EMC1428

1 Overview

The EMC1428 device is a multi channel SMBus temperature sensor with SYS_SHDN and ALERT

outputs. Seven externally connected temperature diodes and one internal diode are available for

temperature sensing. The system shutdown temperature is configurable as is the alert alarm levels.

All of the functions of the EMC1428 can be tested and observed with the USB-based EVB-EMC1428.

A block diagram of this EVB is shown in Figure 1.1.

1.1 Related Documents

The CD included with the evaluation board contains the following documents:

nBill Of Materials

nSchematic

nDatasheets

nChip Manager Application

nChip Manager Register Definition File (EMC1428.xml)

Figure 1.1 EVB-EMC1428 Block Diagram

EMC1428

C8051F320

USB to SMBus Bridge

Temperature

Monitoring

Circuits

USB

Connector

SMBus

Connector

SMBus ALERT

ALERT,

SYS_SHDN

LEDs

EMC1428 EVB User Manual

SMSC EMC1428 Revision 1.0 (08-21-07)

2 Getting Started

2.1 System Requirements

To use the EVB you will need:

nA PC running Windows 2000 or XP

nDisplay resolution 800x600 (or larger to view several windows simultaneously)

nAn available USB port

2.2 Feature Summary

nThe SMSC Chip Manager (ChipMan) application allows viewing and changing register values

nGraphing of any register

nHeaders for connecting an external diode or CPU/GPU

nResistance Error Correction verification

nSaving of settings of all registers allowing for quick loading at a later time

nUSB communication to evaluation board

nAn external SMBus master be easily connected

2.3 Installing the EVB

1. Install the Chip Manager application and device driver on a PC by running Setup.exe from the Chip

Manager distribution CD. A revision history and install/un-install notes may be found in the

readme.txt file on the disk.

2. Connect the supplied USB cable to an available USB port on the PC. Plug the “mini-B” end of the

USB cable into EVB connector P3. The +3.3V and Bridge ACT LEDs should illuminate. After the

EVB is connected to the PC the “Find New Hardware” wizard will pop up for USB driver installation.

Follow the instructions in the readme.txt file to complete the installation process.

3. Start the EVB Software by selecting the Chip Manager application from the SMSC folder from the

Programs Windows Start menu. The EVB will initialize and the Chip Manager Quick Help screen

will appear as in Figure 2.1. The USBAct LED should be blinking when the Chip Manager is

running. For more help with Chip Manager, select Help -> Contents for an html based help

document as shown in Figure 2.2.

Note: The SMSC Chip Manager application allows viewing and changing register values for a variety

of EVBs including the EMC1001, EMC1002, EMC1023, EMC1033 and the entire family of

EMC14XX. The Chip Manager software only needs to be installed once to support all of these

EVBs. The list of supported EVBs may be found in the pulldown menu under Options -> Select

Device.

EMC1428 EVB User Manual

Revision 1.0 (08-21-07) SMSC EMC1428

Figure 2.1 Chip Manager Quick Help Startup Screen

EMC1428 EVB User Manual

SMSC EMC1428 Revision 1.0 (08-21-07)

Figure 2.2 Chip Manager Help Screen

EMC1428 EVB User Manual

Revision 1.0 (08-21-07) SMSC EMC1428

2.4 Board Layout

The EVB was designed for ease of use and user experimentation with easily accessible jumpers and

access to the SMBus data lines. Figure 2.3 below shows the silk-screen for the EVB-EMC1428.

Figure 2.3 EVB-EMC1428 Board Outline and Silk-screen

EMC1428 EVB User Manual

SMSC EMC1428 Revision 1.0 (08-21-07)

3 Hardware Description

3.1 Introduction

The EVB-EMC1428 provides the means to demonstrate all of the EMC1428 features and to view and

modify registers. LEDs indicate status information and test points are included to monitor system

voltages with a user provided voltmeter or oscilloscope.

3.2 USB to SMBus Bridge

The USB to SMBus bridge is based on an 8051 micro controller with integrated USB and SMBus

interfaces as well as internal flash and RAM. During EVB manufacture, firmware is loaded into the

bridge that provides the interface between the USB and the SMBus. Power is sourced to the micro

controller from the USB interface for device power and communication.

3.2.1 Direct SMBus Connect Option

It is also possible to connect an external SMBus master to the EVB-EMC1428. A few jumper settings

are all that is required to drive the EMC1428 on the EVB:

nSimply remove the jumpers on JP19 and connect the SMBus master to the SCL, SDA and ALERT

pins, as well as an external supply for +3.3V.

nThe +3.3V can be supplied by the SMBus bridge by leaving the +3.3V jumper in place and retaining

the USB connection.

3.3 Connecting to Remote Diodes

This EVB is populated with jumpers to connect to an external diode or CPU/GPU. If connecting to a

CPU’s thermal diode, it is necessary to provide a common ground. Also, it is usually necessary to bias

the appropriate CPU Vcc plane above this common ground to avoid forward-biasing the ESD diodes

with the temperature sensor signals. These connections have been provided on P1. Consult the CPU

manufacturer’s datasheet for guidance on interfacing to the thermal diode. Refer to the schematic EVB-

EMC1428-SCH-7122-RevA.pdf for details on the EVB header connections.

3.4 Resistance Error Correction (REC)

External diode 1 on board the EVB-EMC1428 has a series resistance adjustment on the DN line.

Checking the REC (Resistance Error Correction) feature is accomplished by turning the resistor wheel

R1. With REC off, a significant temperature error will result. When the REC bit is set, the error will be

corrected for.

3.5 Power Source

This EVB requires only one USB connection to power the entire board. The USB-SMBus bridge

regulates the +5V USB power to +3.3V used by the EMC1428 and other EVB circuitry.

3.6 Test Points

Test points are provided for:

nGround

nVDD supply pin

n+3.3V power

n+5V_USB power

nALERT and SYS_SHDN outputs

EMC1428 EVB User Manual

Revision 1.0 (08-21-07) SMSC EMC1428

3.7 LED Indicators

LEDs indicate the status of the following signals (Ta ble 3.1 ).

3.8 Jumper Settings

This EVB has many jumper configurations to evaluate the many features of the EMC1428.

This EVB also allows for an off-board diode to be tested (see Ta b l e 3 . 2 ). This is done by removing

both jumpers of the channel of interest. Then connect Pin 1 to the ‘remote+’ terminal of the remote

diode and Pin 3 to the ‘remote-‘ terminal of the remote diode. Make sure a common ground exists

between the remote diode (GPU, etc.) and the EVB-EMC1428. Also ensure that the remote diode is

properly biased according to the diode manufacture.

Table 3.1 LED Status Indicators

LED SIGNAL OFF GREEN RED

LED3 ALERT +3.3V power OFF No ALERT ALERT

LED4 SYS_SHDN +3.3V power OFF NA SYS_SHDN

LED11 +3.3V +3.3V power OFF +3.3V power ON NA

LED12 Bridge Activity NO Activity on

USB/SMBus Bridge

Activity on

USB/SMBus Bridge

LED13 USB Activity NO Activity on USB port Activity on USB port NA

Table 3.2 Remote Diode Configurations

JUMPER CONFIGURATION PIN 1 PIN 2 PIN 3 PIN 4

JP1

On-board diode (Q1) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

JP2

On-board diode (Q2) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

JP3

On-board diode (Q3) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

JP4

On-board diode (Q4) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

JP5

On-board diode (Q5) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

JP6

On-board diode (Q6) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

EMC1428 EVB User Manual

SMSC EMC1428 Revision 1.0 (08-21-07)

A unique feature of the EMC1428 devices is the ability to select the Hardware System shutdown

temperature based on the resistor attached to the TRIP_SET pin and the tri-state setting of the

SHDN_SEL pin. The EVB allows the user to quickly evaluate each of the many temperature values by

adjusting R50. JP12 can be moved to 3 different states which define the powerup state of beta

compensation and REC. Please see the data sheet for detailed operation of these features.

3.9 Default Jumper Settings

Table 3.4 Default Jumper Settings

JP7

On-board diode (Q7) short / DP short / DN

Off-board diode (CPU, GPU, etc.) remote + /

open remote - /

open

Table 3.3 SHDN_SEL Configuration

SHDN_SEL

JP12

CONNECTION DESCRIPTION

VDD 1-2 Transistor Mode

(Beta Comp enabled,

REC enabled)

GND 2-3 Diode Mode

(Beta Comp disabled,

REC enabled)

OPEN OPEN Simple Mode

(Beta Comp disabled,

REC disabled)

JUMPER NAME CONNECTION DESCRIPTION

JP1 External diode 1

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

JP2 External diode 2

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

JP3 External diode 3

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

JP4 External diode 4

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

JP5 External diode 5

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

Table 3.2 Remote Diode Configurations

JUMPER CONFIGURATION PIN 1 PIN 2 PIN 3 PIN 4

EMC1428 EVB User Manual

Revision 1.0 (08-21-07) SMSC EMC1428

Note: dashed line indicates jumper position

3.10 Other Sensor Features

Other features such as Ideality Factor Configuration, Conversion Rate, and Digital Filtering can be

controlled with EMC1428 registers. See the datasheet register description for details.

JP6 External diode 6

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

JP7 External diode 7

off-board

connection

1 - 2

3 - 4

DP connection

DN connection

JP12 SHDN_SEL 1 2 3 (open) Diode mode

JP19 USB to SMBus 1 - 2

3 - 4

5 - 6

7 - 8

+3.3V

SDA - SMBus

SCL - SMBus

ALERT

P1 Bias

connections for

remote CPU

transistor

1 2 (open) Vbias ~ 0.7V

GND

P2 Flash Prog

Header

NA Used in manufacturing

JUMPER NAME CONNECTION DESCRIPTION

Inhaltsverzeichnis

Andere SMSC Hauptplatine Handbücher

SMSC

SMSC EMC1002 Bedienungsanleitung

SMSC

SMSC Microchip USB3803 Bedienungsanleitung

SMSC

SMSC EVB8710 Bedienungsanleitung

SMSC

SMSC UCS1002 EVB Bedienungsanleitung

SMSC

SMSC LAN9303M Bedienungsanleitung

SMSC

SMSC USB3503 Bedienungsanleitung

SMSC

SMSC USB2660i Bedienungsanleitung

SMSC

SMSC EVB-LAN9500A-LC Bedienungsanleitung

SMSC

SMSC EMC1046 Bedienungsanleitung

SMSC

SMSC EVB-USB3340 Bedienungsanleitung

SMSC

SMSC EVB-USB82640 Bedienungsanleitung

SMSC

SMSC EVB-USB3280 Bedienungsanleitung

SMSC

SMSC USB3503 Bedienungsanleitung

SMSC

SMSC LAN9512 Bedienungsanleitung

SMSC

SMSC EVB-EMC1043 Bedienungsanleitung

SMSC

SMSC EVB-LAN9730-MII Bedienungsanleitung

SMSC

SMSC LAN9514 Bedienungsanleitung

SMSC

SMSC EVB-USB2514Q36-BAS Bedienungsanleitung

SMSC

SMSC LAN9303 Bedienungsanleitung

SMSC

SMSC EVB-USB2240-IND Bedienungsanleitung

SMSC

SMSC EVB-USB3320 Bedienungsanleitung

SMSC

SMSC USB3750 Bedienungsanleitung

SMSC

SMSC EVB-USB5534-01 Bedienungsanleitung

SMSC

SMSC EVB-USB4640 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung