Snap-On Level 5 VTC eLock 200 Series Bedienungsanleitung

200/300 Series — VTC eLock Instructions

200/300 Series

– VTC eLock Instructions

Thank you for purchasing the VTC eLock.The information

contained in these instructions is intended to serve as a

guide so as to allow the eLock to be quickly and easily

put into service. 300 Series eLock can be conﬁgured to

work in conjunction with existing 802.11g or Ethernet

networks.

For complete set up and installation instructions for

networked and stand-alone eLocks, please see the

“Help” section in LockView NTC/VTC Software v4.

1. Dot matrix LCD

2. Network button (blue LED)

3. “UP” button

4. “NEXT/SELECT” button

5. “BACK/CANCEL” button

6. “MENU” button

7. “DOWN” button

8. + Button

9. - Button

10. Low battery indicator

(yellow LED)

11. Magstripe reader location

(if equipped)

12. HID Prox or HID iCLASS

reader location (if

equipped)

13. “ENTER” button

14. “CLEAR” button

15. Alpha-numeric keypad

78 9 10

VTC eLock controller

Network VTC eLock has three components:

Controller Motorized gear-driven latch Control module / battery compartment

Exterior mount

Interior mount

VTC

200/300 Series — VTC eLock Instructions

200/300 Series VTC eLock — Components

Front view:

eLock controller

Back view: VTC

eLock controller

Battery cable connector

Integrated Wi-Fi

antenna cable

included for 300

Series Wi-Fi version

200/300 Series VTC eLock Components

9V Battery

Jumper Port

USB Port for direct connection

to LockView software

200/300 Series — VTC eLock Instructions

200/300 Series VTC eLock — Components continued

Control module /

battery compartment

1 2 3 4 5 6 7

1. Door switch connector (door

switch not included)

2. Wi-Fi antenna cable connector

or Ethernet connector

(Wi-Fi

connector shown; 300 Series only)

3. Control module / battery cable

connector

4. 2.5 mm AC adapter plug-in

(adapter not included)

5. Ground terminal

6. Dual eLatch connector (Latch 2, if

equipped; one latch is included)

7. Latch connector (Latch 1; one

latch is included)

8. Battery pack cover (6-AA batteries

not included)

200/300 Series — VTC eLock Instructions

Unit Features:

wChoose 802.11g or Ethernet Networked configurations that

uses the facilities existing infrastructure for actual 2-way

read/write communication

wEach eLock can hold any combination of up to 3,000

Supervisors and Users

wChoose a model to use existing HID Prox, HID iCLASS, or

magstripe card credentials that can be programmed to

operate each eLock

wRemote Notification System with programmable escalating

alerts via SMTP email; SMS text, voice and fax (Networked

eLock & LockView NTC/VTC Software v4 required)

wSpring bolt latching mechanism provides automatic

relocking

wOptional second latch drive output (requires additional

hardware)

wDoor position switch input (requires additional hardware)

wMembrane keypads with stainless steel domes provides

durable performance and easy cleaning

What’s in the box?

w1 – eLock controller

w1 – motorized latch w/latch cable

w1 – control module / battery compartment with interconnect

cable

w1 – serial code sticker set

w1 – in-box instructions

What’s needed?

w6 – AA alkaline batteries

wT15 pin-in Torx (6-lobe) bit or driver

Care and Cleaning

The eLock is a battery operated device, therefore, it should

be part of a regular battery maintenance program.

Warning: install the batteries as shown in the battery

compartment. Polarity (+) or (-) must be correct. Replace

batteries as a set. Always use new batteries when replacing

the old set. Do not combine a used battery with a new one.

Only use alkaline batteries; do not mix battery types.

To clean the surface of the eLock, apply non-acid based

cleaner to a clean cotton cloth; do not spray cleaner directly

on the eLock. Wipe down keypad and housing taking care

around the beeper opening and edges of keypads. Wipe

excess cleaner off of all surfaces.

Setting up the eLock

Getting Started Out of the Box

If the eLock is stand-alone 200 Series (direct connection

via USB to LockView NTC/VTC Software v4) and will be

used in conjunction with LockView NTC/VTC Software v4,

please follow the LockView Mode Instructions on page 6.

For Networked (802.11g or Ethernet) 300 Series eLocks,

please follow the eLock Database & Network Conﬁguration

& Install Manual and the LockView NTC/VTC Software v4

Instruction Manual before proceeding.

INITIAL PROGRAMMING:

The unit is shipped with a preprogrammed 2801 Supervisor

code.

Credential Menu

ADD CREDENTIAL

Note: There are two status levels; Supervisor and User. Each

eLock can hold any combination of up to 3,000 Supervisors

and Users.

Only Supervisors are allowed to ADD Users and Supervisors.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Enter 2801 and press “ENTER.”

3. Press “DOWN” button to highlight CREDENTIAL MENU and

press “NEXT/SELECT.”

4. Highlight ADD CREDENTIAL and press “NEXT/SELECT.”

5. CREDENTIAL TO ADD will be displayed. Scan new credential

or enter new 4-14 digit PIN and Press “ENTER.”

6. Adding credential will be displayed.

7. Default status is User. To change status to Supervisor press

the +button.

8. The new User/Supervisor will be added to the next available

slot number. To change the slot number, press “UP” and then

+/- to move to next available slot; or use the numeric keypad

to enter the desired slot number and press “NEXT/SELECT.”

200/300 Series VTC eLock — Instructions

200/300 Series — VTC eLock Instructions

9. CREDENTIAL NAME ENTRY will appear. Press 2 - 9 for A - Z;

press 1 for -, ., +or _; press 0 for “space”; press and hold

0 - 9 for numbers. (Maximum number of allowed characters

is 14.)

10. Press “ENTER” when done. STORED will be displayed when

complete.

Operating the eLock

Follow the instructions below to operate the eLock.

PIN CREDENTIAL

1. Enter a valid PIN (between 4 - 14 digits) and

2. Press “ENTER.”

CARD CREDENTIAL

If the eLock is equipped with a card reader (HID Prox, HID

iCLASS or a Magstripe)

1. Present a valid card within range of the HID reader or slide

the magstripe card through the magstripe reader.

DUAL CREDENTIAL

If the User or Supervisor requires a dual credential

1. Enter a valid PIN and press “ENTER” (for keypad credentials)

or present a valid card (for HID Prox or HID iCLASS or

Magstripe credentials).

2. Enter the second credential (4-14 digit PIN) and press

“ENTER.”

NOTE: THE SECOND CREDENTIAL MUST ALWAYS BE

A 4 - 14 DIGIT PIN

PASSAGE MODE

(LockView software required) To hold the latch bolt in the

open position indefinitely, there is a setting in LockView

called Passage Mode.

Passage Mode can be assigned to an eLock and/or a

Supervisor/User credential.

In LockView, via the Lock Editor, Passage Mode can be

selected so that every valid User or Supervisor that has

access rights to the eLock can place it in passage mode.

In LockView, via the User Editor, Passage Mode can be

selected. Users and Supervisors can place any eLock to which

they have access right into Passage Mode. This is regardless

of whether or not Passage Mode has been activated in the

eLock.

To place an eLock into Passage Mode:

PIN CREDENTIAL

1. Enter a valid PIN (between 4 - 14 digits) and press “ENTER.”

2. Press “ENTER” again. HOLD OPEN will flash; LOCK IS HELD

OPEN will appear in the upper left hand corner of the LCD.

CARD CREDENTIAL

If the eLock is equipped with a card reader (HID Prox, HID

iCLASS or Magstripe):

1. Present a valid card within range of the HID reader or slide

the magstripe card through the magstripe reader.

2. Press “ENTER.” HOLD OPEN will flash; LOCK IS HELD OPEN

will appear in the upper left hand corner of the LCD.

DUAL CREDENTIAL

If the User or Supervisor requires a dual credential:

1. Enter a valid PIN and press “ENTER” (for keypad credentials)

or present a valid card (for HID Prox, HID iCLASS or magstripe

credentials).

2. Enter the second credential (4-14 digit PIN) and press

“ENTER”

3. Press “ENTER” again. HOLD OPEN will flash; LOCK IS HELD

OPEN will appear in the upper left hand corner of the LCD.

NOTE: THE SECOND CREDENTIAL MUST ALWAYS BE A 4 - 14

DIGIT PIN

To EXIT Passage Mode (re-lock the unit/extend the eLock

latch bolt):

PIN CREDENTIAL

1. Enter a valid PIN (between 4 - 14 digits)

2. Press “ENTER.” EXITING PASSAGE MODE will flash on the

LCD and the latch bolt will extend.

CARD CREDENTIAL

If the eLock is equipped with a card reader (HID Prox, HID

iCLASS or Magstripe):

1. Present a valid card within range of the HID reader or slide

the magstripe card through the magstripe reader. EXITING

PASSAGE MODE will flash on the LCD and the latch bolt will

extend.

DUAL CREDENTIAL

If the User or Supervisor requires a dual credential:

1. Enter the primary valid PIN (for keypad credentials) and

press “ENTER” or present the valid card (for HID Prox, HID

200/300 Series VTC eLock — Instructions continued

200/300 Series — VTC eLock Instructions

iCLASS or Magstripe credentials). EXITING PASSAGE MODE

will flash on the LCD and the latch bolt will extend.

Methods to begin building

a database of eLocks in

LockView Software

Note: Supervisor, User and parameter changes that already

exist in the eLock will automatically be carried into

LockView once the eLock has been enrolled.

For Networked (802.11g or Ethernet) eLocks, please follow

the eLock Database & Network Conﬁguration & Install

Manual and the LockView NTC/VTC Software Instruction

Manual before proceeding.

LockView Mode Instructions

(For complete details on how to build a database of

users and eLocks, see the LockView NTC/VTC Software

Instruction Manual and eLock Manual Programming Guide)

LockView NTC/VTC Software v4 must be installed and the

eLock must be in SETUP mode before continuing. (See

Setup Code section on page 10.)

Stand-alone eLocks (Direct USB connection to laptop

computer with LockView is required) There are two methods

that can be used to add eLocks to the LockView software.

Automatic Method

1. With the eLock in SETUP mode, connect the eLock via the

USB cable to the computer on which LockView is installed.

2. Login to LockView.

3. After 30 seconds, the below will appear.

NOTE: After 5 minutes of inactivity, the eLock will exit SETUP

mode.

4. Click Yes.

5. The below will appear. Type in the name of the lock.

**Once a Lock Name has been chosen in LockView, it can

not be changed. Please be sure the name that is chosen is

the one that will be used in the future.

6. Click Save when done.

7. Go to Lock Editor tab in Lock/User Editor.

8. Left click to highlight the name of the lock and then click Edit

Lock.

9. Verify and/or adjust all other lock parameters. (See LockView

NTC/VTC Software Instruction Manual for complete

details.)

10. Click OK when done.

Manual Method

1. Login to LockView.

2. Go to Lock/User Editor; Lock Editor tab and click Add Lock.

3. Enter the required information: Lock Name; Lock Serial

Number and Setup Code (supplied on green sticker set as

Setup Cd).

**Once the Lock Name has been chosen in LockView, it can

not be changed. Please be sure the name that is chosen is

the one that will be used in the future.

4. Verify and/or adjust all other lock parameters and click OK.

(See LockView NTC/VTC Software Instruction Manual for

complete details on these options)

5. With the eLock in SETUP mode, connect the eLock via the

USB cable to the computer on which LockView is installed.

6. After 30 seconds, the lock will be updated in LockView. Click

Refresh to prompt the update.

NOTE: After 5 minutes of inactivity, the eLock will exit SETUP

mode.

200/300 Series VTC eLock — Instructions continued

200/300 Series — VTC eLock Instructions

200/300 Series VTC eLock — Manual Programming

Credential Menu

ADD CREDENTIAL

Note: There are two status levels; Supervisor and User. Each

eLock can hold any combination of up to 3,000 Supervisors

and Users.

Only Supervisors are allowed to ADD Users and Supervisors.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and Press

“ENTER.”

3. Press “DOWN” button to highlight CREDENTIAL MENU and

press “NEXT/SELECT.”

4. Highlight ADD CREDENTIAL and press “NEXT/SELECT.”

5. CREDENTIAL TO ADD will be displayed. Scan new credential

or enter new 4-14 digit PIN and Press “ENTER.”

6. Adding credential will be displayed.

7. Default status is User. To change status to Supervisor press

the +button.

8. The new User/Supervisor will be added to the next available

slot number. To change the slot number, press “UP” and then

+/- to move to next available slot; or use the numeric keypad

to enter the desired slot number and press “NEXT/SELECT.”

9. CREDENTIAL NAME ENTRY will appear. Press 2 - 9 for A - Z;

press 1 for -, ., +or _; press 0 for “space”; press and hold

0 - 9 for numbers. (Maximum number of allowed characters

is 14.)

10. Press “ENTER” when done. STORED will be displayed when

complete.

DELETE CREDENTIAL

Note: There are two status levels; Supervisor and User.

Only Supervisors are allowed to DELETE Users and

Supervisors.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and Press

“ENTER”

3. Press “DOWN” button to highlight CREDENTIAL MENU and

press “NEXT/SELECT”

4. Highlight DELETE CREDENTIAL and press “NEXT/SELECT”

5. Credential to Delete will be displayed. All of the occupied

slots along with the name (if one exists) will be listed. If

the status of the credential is a supervisor, an asterisk (*)

appears next to the slot number. Press “MENU” to re-sort

by slot number, alphabetically by name, or showing all

supervisors first.

6. Press ‘UP” / “DOWN” to scroll by line or +/- to scroll by

page to highlight credential to be deleted and press “NEXT/

SELECT.”

7. Press “UP” and “NEXT/SELECT” to delete. DELETED will be

displayed when complete.

8. Press “BACK/CANCEL” to return to CREDENTIAL MENU.

VIEW CREDENTIAL

Note: There are two status levels; Supervisor and User.

Only Supervisors are allowed to VIEW Users and Supervisors.

1. Press “MENU” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and Press

“ENTER.”

3. Press “DOWN” button to highlight CREDENTIAL MENU and

press “NEXT/SELECT”

4. Highlight VIEW CREDENTIAL and press “NEXT/SELECT”

5. Credential to View will be displayed. All of the occupied slots

along with the name (if one exists) will be listed. If the status

of the credential is a supervisor, an asterisk (*) appears next

to the slot number. Press “MENU” to re-sort by slot number,

alphabetically by name, or showing all supervisors first.

6. Press “UP”/“DOWN” to scroll by line or +/- to scroll by page to

highlight credential to be viewed and press “NEXT/SELECT.”

7. Press “NEXT/SELECT” to display NAME, SLOT NUMBER, LAST

ACCESS ATTEMPT.

8. Press “DOWN” to display CREDENTIAL TYPE (KEYPAD, PROXCARD

or MAGSTRIPE CARD)

9. Press “DOWN” again to display the ACCESS SCHEDULE

(TIME AND DAY RESTRICTIONS AS SET IN LOCKVIEW).

10. Press “BACK/CANCEL” to return to CREDENTIAL MENU.

EDIT CREDENTIAL

Note: There are two status levels; Supervisor and User.

Only Supervisors are allowed to EDIT Users and Supervisors.

1. Press “MENU” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and Press

“ENTER”

3. Press “DOWN” button to highlight CREDENTIAL MENU and

press “NEXT/SELECT”

4. Highlight EDIT CREDENTIAL and press “NEXT/SELECT”

5. Credential to Edit will be displayed. All of the occupied slots

along with the name (if one exists) will be listed. If the status

of the credential is a supervisor, an asterisk (*) appears next

to the slot number. Press “MENU” to re-sort by slot number,

alphabetically by name, or showing all supervisors first.

200/300 Series — VTC eLock Instructions

200/300 Series VTC eLock — Manual Programming continued

6. Press ‘UP” / “DOWN” to scroll by line or +/- to scroll by page

to highlight credential to be edited.

7. Press “NEXT/SELECT” to edit highlighted credential

8. Press +/- to change Level (Supervisor/User); press “UP/

DOWN” to highlight 2nd PIN. To add a new or change an

existing 2nd PIN, enter a 4 - 14 digit number using the

numeric keypad. Press “ENTER” when done. Confirm the

new/changed PIN by entering it again when prompted. Press

“ENTER” when done.

9. Press “BACK/CANCEL” to return to CREDENTIAL MENU.

SET/EDIT YOUR 2nd PIN

Note: There are two status levels; Supervisor and User.

Only Supervisors are allowed to SET/EDIT YOUR 2nd PIN.

The steps below will make the logged in credential a Dual

Credential Supervisor requiring a 2nd PIN.

Follow the EDIT CREDENTIAL steps to add/change dual

credential status for other Supervisors or Users.

1. Press “MENU” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and Press

“ENTER”

3. Press “DOWN” button to highlight CREDENTIAL MENU and

press “NEXT/SELECT”

4. Highlight SET YOUR 2nd PIN and press “NEXT/SELECT.” (EDIT

YOUR 2nd PIN will appear if a second PIN credential already

exists)

5. Type new 2nd PIN will be displayed. Enter new 4 - 14 digit

PIN and press “NEXT/SELECT.”

6. Type 2nd PIN again will appear. Enter the 4 - 14 digit PIN

again and press “NEXT/SELECT.” NEW PIN SET will appear.

Display Formats

Using DISPLAY FORMATS, the following can be adjusted:

HOURS: AM/PM or 24 HOUR

M-F/DATE:

wMON-SUN; MM/DD/YY;

wMON-SUN; MMM D ‘YY;

wMON-SUN; DD-MM-YY;

wMON-SUN; DD-MMM-YY

wMON-SUN; YYYY-MM-DD

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and press

“ENTER.”

3. Press “DOWN” button to highlight DISPLAY FORMATS and

press “NEXT/SELECT.”

4. DISPLAY FORMATTING will be displayed.

5. Press “UP”/“DOWN” buttons to select and +/- buttons to

adjust.

6. Press “NEXT/SELECT” when done.

Set Date/Time

Using SET DATE/TIME, the following can be adjusted:

SETUP TIME ZONE (INCLUDING AUTO DAYLIGHT SAVING)

SET DATE (MONTH, DAY, YEAR)

SET TIME (HOUR, MINUTE, AM/PM)

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and press

“ENTER.”

3. Press “DOWN” button to highlight SET DATE/TIME and press

“NEXT/SELECT.”

4. DATE/TIME MENU will be displayed.

5. Press “UP”/“DOWN” to scroll and “NEXT/SELECT” to modify.

6. Press “UP”/“DOWN” buttons to select and +/- buttons to

adjust.

7. Press “NEXT/SELECT” when done.

8. Press “BACK/CANCEL” to return to main menu.

Network Test (if equipped)

Using NETWORK TEST the strength and quality of the eLock

connection to the network is displayed. The IP and MAC

addresses are also shown here.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and press

“ENTER.”

3. Press “DOWN” button to highlight NETWORK TEST and press

“NEXT/SELECT.”

4. NET STATUS will be displayed as well as Str: & Qual:, IP

address and MAC address.

5. Press “CLEAR” to exit.

LCD Contrast

Using LCD CONTRAST, the LCD contrast can be adjusted:

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and press

“ENTER.”

3. Press “DOWN” button to highlight LCD CONTRAST and press

“NEXT/SELECT.”

200/300 Series — VTC eLock Instructions

200/300 Series VTC eLock — Manual Programming continued

4. LCD Contrast will be displayed.

5. Enter 1 - 9 on numeric keypad or +/- buttons to adjust.

6. Press “NEXT/SELECT” when done.

7. Press “BACK/CANCEL” to return to main menu.

LCD Backlight

Using LCD BACKLIGHT the brightness of the display can be

adjusted.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and press

“ENTER.”

3. Press “DOWN” button to highlight LCD BACKLIGHT and press

“NEXT/SELECT.”

4. LCD Backlight will be displayed.

5. Enter 0 - 9 on numeric keypad or +/- buttons to adjust.

(“0” = OFF)

6. Press “NEXT/SELECT” when done.

Set Beep Volume

Using SET BEEP VOLUME, the audible beep can be

adjusted.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and press

“ENTER.”

3. Press “DOWN” button to highlight SET BEEP VOLUME and

press “NEXT/SELECT.”

4. Beep Volume will be displayed.

5. Enter 0 - 9 on numeric keypad or +/- buttons to adjust.

(“0” = MUTE)

6. Press “NEXT/SELECT” when done.

7. Press “BACK/CANCEL” to return to main menu.

Reset Net Schedule

A PROPERLY CONFIGURED AND ENABLED NETWORK eLock

IS REQUIRED TO MAKE USE OF THIS FEATURE.

Only Supervisors are allowed to RESET NET SCHED.

Using RESET NET SCHED. the scheduled network check-in

time can be set.

1. Press “MENU.” LOGIN PLEASE will be displayed.

2. Scan valid credential or enter 4-14 digit PIN and Press

“ENTER.”

3. Press “DOWN” button to highlight RESET NET SCHED. and

press “NEXT/SELECT.”

4. NETWORK TIMING RESET will be displayed. The eLock will

follow the programmed or default check-in frequency from

this time of day forward.

For example:

Programmed Update Interval as set in LockView is 12 hours

(twice/day). The time of day was 10 a.m. when the eLock

was initialized.

Therefore, the eLock update time is 10 a.m. and 10 p.m. The

desired update time is 6 a.m. and 6 p.m.

Using the RESET NET SCHED. feature, the above steps should

be followed at 6 a.m. or 6 p.m.

Name of last credential on LCD

The name, time, day and date of the last credential to

successfully access the eLock appears at the bottom of the

reader display.

200/300 Series — VTC eLock Instructions

Setup Code

**In order to ensure the security of the application on

which the eLock will be installed, the setup code (supplied

on green sticker set as Setup Cd) must be kept in a safe

location.**

If required, the eLock can be placed in setup mode.

1. Press and Hold “CLEAR” on eLock keypad. ENTER SETUP

CODE will appear.

2. Enter the setup code (supplied on green sticker set as Setup

Cd) and press “ENTER”

3. SETUP CODE will appear in the upper left hand corner of the

eLock LCD. (The eLock will exit setup mode after 5 minutes of

inactivity). Press “CLEAR” on the eLock keypad to exit SETUP

mode. READY will be displayed in the upper left hand corner

LCD)

SETUP mode would be necessary in the event that:

1-- eLock should be added to the database in LockView.

2-- It became necessary to restore the original factory settings,

(FACTORY RESET); disable the Wi-Fi or Ethernet module,

(TURN OFF/ON NETWORK); or disable the eLock temperature

probe, (TURN OFF THERM).

Factory Reset

In the event that it becomes necessary to erase ALL

Supervisors/Users and log entries from the eLock and reset

all settings to the original factory defaults, a FACTORY RESET

may be performed.

WARNING: ONCE A FACTORY RESET IS PERFORMED, IT

CANNOT BE REVERSED.

1. Press and hold “CLEAR” on the keypad.

2. ENTER SETUP CODE will be displayed. Enter the set up code

and press “NEXT/SELECT.”

3. SETUP will be appear in the upper left hand corner of the

eLock LCD.

4. Press the “MENU” button.

5. Press “UP” button to highlight FACTORY RESET and press

“NEXT/SELECT.”

6. Press “UP” button to highlight FULL RESET.

7. Press and Hold “NEXT/SELECT” to reset.

8. Factory will appear in the upper left hand corner of the

eLock LCD. Note: whenever eLock is in factory mode, it is

considered unsecured.

Stand-alone & Networked eLock

Alarm States

The eLock has programmable ALARM/ALERT STATES.

1) Battery Low

(A properly configured and enabled network eLock is

required to make use of this feature.)

Battery Low can be programmed to send an alert(s) via

LockView’s Remote Alert Messaging if the eLock battery

power drops below a defined level.

Note: There is no audible alarm that can be triggered at the eLock,

however there is a yellow LED low battery indicator (LOW BATT) on the

eLock keypad.

(See LockView Manual for NOTIFIER explanation)

2) Door Ajar

(Door switch – NOT INCLUDED – must be installed and enabled

in order to make use of this feature)

Door Ajar is intended to trigger an alarm at the eLock if the

application door has been left opened.

After the programmed or default eLock latch open time has

expired, the Door Ajar timer begins. The Door Ajar timer is

programmable in LockView in one second increments. The

door ajar alarm will be triggered if this time expires before

the door switch closes.

The eLock will stop alarming after the door switch closes.

(See LockView Manual for NOTIFIER explanation)

3) Unauthorized Entry

(Door switch – NOT INCLUDED – must be installed and enabled

in order to make use of this feature)

Unauthorized Entry is intended to trigger an alarm at

the eLock in the event of an application “break-in.” The

Unauthorized Entry alarm will sound when the door switch

opens and the eLock latch bolt is in the extended position.

The eLock will stop alarming after a valid credential is

presented.

(See LockView Manual for NOTIFIER explanation)

200/300 Series VTC eLock — Manual Programming continued

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Snap-On Industrieanlagen Handbücher

Snap-On

Snap-On POLARTEK PLUS EEAC331 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung