SOARNEX EWC-100 Bedienungsanleitung
Easy Wireless Controller (EWC)
無線控制器
EWC-100 & EWC-100-62W
EWC-100 & EWC-100-62W 系列
Quick Installation Guide
快速安裝指南
Rev. 1.0 Aug. 2017
EN
Contents of Packing
Open the shipping carton and carefully unpack its
contents. The carton should contain the following items.
1. EWC-100 series device x 1
2. DC Power adapter (w/ AC power cord):
Power adapter (AC input:100-240v/0.5A, 50/60Hz,
DC output: 12V/1A) for EWC-100
Power adapter (AC input: 100-240v/1.2A, 50/60Hz,
DC output: 54V/1.67A) for EWC-100-62W
3. Rack mount kit x 1
4. Rubber Footpads x 4
5. Quick Installation Guide QR cod card x 1
♦Install the EWC device in a suitable temperature / humidity
environment.
♦ The power outlet should be within 1.82 meters (6 feet) of
the EWC device.
♦ Make sure that there is proper heat dissipation and
adequate ventilation around the EWC device.
♦ Do not place any heavy objects above the EWC device.
♦ Users can check more technical specications from
http://www.soarnex.com if necessary.
!NOTE:
EN
LED Indicators
EWC-100
Front Panel
EWC-100-62W
LED Indicator Color Status Description
Power Green Solid light Power on
Blinking System boot up
Off Light off Power o
USB Green Solid light When USB flash disk plug in
Off Light off No USB flash disk plug in
LAN
(EWC-100)
Green Solid light The port is transmitting or
receiving data
Off Light off No link
Upper LED
1-5 (LAN)
(EWC-100-62W)
Green Blinking The port is transmitting or
receiving data
Off Light off No link
The LEDs of the switch are located on the front panel.
POWER / SYSTEM LAN
EWC-100
1 2 3 4 5
POE MAX
EWC-100-62W
EN
LED Indicator Color Status Description
Lower LED
1-4 (PoE)
(EWC-100-62W)
Green Solid light The PoE port has supplied
power normally
Off Light off There is no PoE power device
(PD) connection
PoE Max
(EWC-100-62W)
Amber Solid light When the total PoE output
power achieve Guard Band
Off Light off System still have power for
new PD
Please check the detailed specification from
http://www.soarnex.com if necessary.
EN
EWC-100
Rear Panel
EWC-100-62W
K-Lock,anti-theft to prevent or deter the unautho-
rized appropriation.
For rmware upgrade, backup/ restore congurati-
on functions.
EWC-100DC power socket accepts unput power
12V/1A.
EWC-100-62W DC power socket accepts unput
power 54/1.67A.
On/ O Power switch (for EWC-100)- Push the controller
On/ O push button to turn your controller “On”
(Inner position) or “O” (Outer position).
Reset button- Press and hold this button for 15
seconds and release to reset the controller to
factory defaults. The ports LEDs will trun off to
indicate that the reset was initiated.
USB
DC
IN
DC
IN
RESET
12345RESETUSB DC
IN
12345RESETUSB DC
IN
EN
Side Panel
The left and right side panel of the EWC device have heat vents
to dissipate heat.
•Do not block these openings, and leave at least 10cm to make
sure that the environment is well ventilated.
EN
29072466E1062W0
Hardware Installation
1. Attach the rubber footpads to the recessed area on
the bottom of the EWC device.
2. Place the EWC device on a at desk or shelf.
5. Plug the power cord into the power socket of the
EWC device.
3. Attach the mounting brackets on the both sides of
the EWC device and secure them with the screws.
4. Then, mount the EWC device to a rack with the screws.
1 2 3 4 5
POWER MAX
EP100-05-31
POWER / SYSTEM LAN
EWC-100
1 2 3 4 5
POWER MAX
EP100-05-31
POWER / SYSTEM LAN
EWC-100
1 2 3 4 5
POWER MAX
EP100-05-31
POWER / SYSTEM LAN
EWC-100
EN
6. Keep enough ventilation space between the EWC
device and the surrounding objects.
7. Connect your wireless access points.
RADIUS DHCP
WAN
EWC-100-62WEWC-100
PoE Switch
Access Point
Access Point
LAN
w/ DHCP Serverw/ DHCP Server
LAN
EN
Conguration
How to congure the EWC device via WEB brower is
shown as below:
• Please make sure the computer MUST be set on the same
IP Subnet (same as the IP address of tyhe EWC device)
•For example, the default IP address of the EWC device
is 192.168.1.100 with subnet mask 255.255.255.0, then
the computer should be set 192.168.1x (where x is a
number between 1-254, expect 100)with subnet mask
255.255.255.0.
EN
Conguration
1. Login the EWC device via browser
Open your web browser and enter http://192.168.1.100
(the factory-default IP address) to access the WEB
platform. Default User Name and Password of the EWC
device are “admin”.
Note,You can congure the EWC device by entering the
User Name/Password and IP Address via WEB platform.
2. Recovering Back to Factory Default Conguration
If you’ve forgotten the User Name or Password or IP
Address which has been changed, and then you can
reset it to factory default settings through console
port. After the EWC device has rebooted, you can login
the EWC device via web browser and enter IP Address
http://192.168.1.100 with the default User Name/Pass-
word (the factory-default is “admin”).
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere SOARNEX Controller Handbücher
