Solaira SMaRT 16-DV Bedienungsanleitung

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 1

Solaira SMaRT 16-DV Variable Controller

Installation & User Manual

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

SAFETY WARNING

ALL INSTALLATIONS/SERVICE MUST ONLY BE

PERFORMED BY A LICENSED/CERTIFIED ELECTRICIAN

TO LOCAL AND NATIONAL ELECTRICAL CODE (NEC).

WARNING: SHOCK AND FIRE HAZARD:

• Serious injury or death could occur

• Disconnect ALL power sources before removing cover. Power should only be re-connected after

electrical installations are complete and cover replaced

• Be certain the power source conforms to specifications outlined on heater label

• Maximum heater load SHOULD NOT EXCEED 16 AMPERE

• Control MUST BE PROPERLY grounded. Assure to connect ground wire green wire from heater

to ground connection from electrical supply, not to a live or “hot” conductor.

• Engineer/Electrician/Installer to determine suitability of this appliance in intended application and

compliance with all local, state/provincial and National electrical Code (NEC) requirements

• Do not use locations containing hazardous or explosive atmospheres.

ELECTRICAL RATING

Maximum load 16A @110-120V or 208-240VAC 50/60HZ

WARNING SERIOUS INJURY OR DEATH COULD OCCUR, DISCONNECT ALL POWER

PRIOR TO SERVICE

SPE-1000 CANADA INSPECTED

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 2

INTRODUCTION

The Solaira SMaRT 16-DV Control has a 1 to 5 step setting allowing you to find the optimum comfort setting in

your specific area.

To increase output to full output, press and release red button.

To increase in increments, press and hold the red button until the desired number is reached.

To reduce output to OFF, press and release red button.

To reduce in increments, press and hold the red button until the desired number is reached

FEATURES

• Variably control your Solaira° heaters, up to a max load of 16A.

• Weatherproof control for exposed, wet conditions (it is the electrician responsibility to assure correct

water tight connection, this may necessitate replacing included watertight strain relief)

• Variable Control – Ability to adjust output to desired comfort level

• Soft Start – Zero current switching point which can extend emitter lamp life

• Input for Temperature Monitoring Accessory – Solaira SMaRT 16-DV Variable control is input ready for

a local (on controller) temperature monitor that is sold separately.

OPTIONAL ACCESSORIES (Sold Separately)

WARNING: The SMaRT-16DV can be used with the following approved accessories. Use of

any other control Interface is not recommended.

•Handheld IR Remote (SMRTVMT): Is an optional handheld remote that communicated via IR to

either the SMaRT Controller or Optional Wall Switch (SM-WSD). Must be in line of sight of the

controller.

•Wall Switch (SM-WSD): Is a mounted wall switch unit that provides control of a the SMaRT-16DV,

that may be remotely located. The remote-control wall switch unit is supplied mounted on a single

gang faceplate, ready to be fitted to a single gang certified J-box. As supplied the unit must be installed

indoors in a dry environment, if the unit needs to be installed outdoors or in a wet environment it must

be installed onto a certified J-box, which is itself installed inside a water resistant, IP65 rated enclosure

and to all appropriate local and NEC codes. The SM-WSD can also interface with the Handheld IR

Remote SMRTVMT, which must be in line of sight of the SM-WSD.

•Occupancy SENSOR (SMRTOCC): A passive infrared (PIR) external sensor, with a range of

approximately 12m, can monitor the selected area ensuring heaters only switch on when the zone is

occupied.

•Temperature Monitoring Accessory: This will allow user to pre-set the minimum temperature level

that will allow the controller to operate when a temperature monitor is purchased separately. Note: the

temperature monitor is calibrated in Celsius; please use the following table to aid in set up:

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 3

Fahrenheit

Celsius

Fahrenheit

Celsius

32.0

0.0

55.0

12.8

36.0

2.2

60.0

15.6

40.0

4.4

65.0

18.3

45.0

7.2

70.0

21.1

50.0

10.0

75.0

23.9

80.0

26.7

•Temperature Monitor (SMRTVTEM-R): The controller can be equipped with a remotely located

temperature sensor that monitors the temperature of the desired zone and inhibits the heaters when the

temperature exceeds a pre-determined set point of between 41°F (5°C) to 77°F (25°C).

WARNING: Use of standalone Solaira SMRTOCC40 and SMRTOCC60 are for

standalone controls ONLY and may not be paired with SMaRT16-DV. FAILURE

TO COMPNY MAY RESULT IN CONTROLLER DAMAGES.

WARNING: Solaira SMaRT 16-DV Variable control is a high power electrical

device and MUST ONLY BE INSTALLED BY A CERTIFIED ELECTRICIAN

TO LOCAL AND NATIONAL ELECTRICAL CODE.

INSTALLATION

The control can be installed in a convenient VENTED location and does not have to be installed in the immediate

area of the heaters. The unit is shipped with the Occupancy sensor/pushbutton input fitted with a wire link which

continually re-triggers the "ON" timer so that it never expires.

If the user decides to utilize the optional Occupancy Sensor (Sold Separately), the occupancy sensor should be

mounted 8’ (2.5 + Meters) above of the floor. Ceiling mounting is preferred but not essential. The Optional

Occupancy monitor must not be mounted directly in line with the heaters output, highly reflective surfaces,

radiators or other thermostatically controlled heaters or open doorways with people walking past.

WARNING: CONTROLLER MOUNTING

DO NOT mount the controller directly on any flammable material i.e. wood

or any other combustible. Controller must be mounted via standoffs (supplied &

specified by others) to aid in heat dissipation, as per local building and NEC code

INITIAL START UP WITH OPTIONAL OCCUPANCY SENSOR

• Occupancy Sensor (SMRTOCC) (sold separately), it takes 60 seconds to set before detection takes place

• Optional Occupancy Sensor continues to monitor the area and will reset to the set time every time it

detects movement.

• Before testing ensure the wiring is correct.

• Temperature trip point has already been pre-set at the factory.

• Timer is preset to 1 minute but can be adjusted using timer trimmer potentiometer to 1-60 minutes.

• The expected detection area can now be “walked tested” using the diagram shown in mind. The area

should be crossed in various directions to ensure coverage is as expected.

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 4

DISPLAY FEATURES

Display shows ‘t’ The unit is turned OFF as the ambient temperature is above the trip level set by

TEMPERATURE SETPOINT.

Display shows "0" The output is OFF

Display shows "1", "2", The unit is ON at the indicated power level

"3", "4"

Display shows ‘F The unit is set to FULL output.

Display flashing "." The "ON" timer has expired and is waiting to be re-triggered by the Occupancy

sensor (i.e. no movement detected for "ON" time)

Display "." The unit is in Standby mode pressing the optional fully on

remote control POWER button will toggle the power ON and OFF.

You can check the remote control is transmitting by observing the "." (dot) flashing rapidly.

TROUBLE SHOOTING

Heater does not come on, t in display….The heater pre-set trip temperature IS ABOVE THE AMBIENT

TEMPERATURE. This can be adjusted using the temperature set point potentiometer.

Heater does not come on, flashing DOT…The controller is waiting for input from optional occupancy sensor. If

your system does not utilize the occupancy sensor, then wire jumper (factory installed) must be in place in PIR

SENSOR INPUT on pins SIG IN and COM. If the jumper is not in place, controller will not operate.

SPECIFICATIONS

Max load at 20°C ambient

Voltage

Power Consumption

Occupancy Sensor

(option)

Pushbutton Timer (option)

Set Time Period

Temperature Set point

Factory Set Temperature trip point

2 heater Installation

Ambient Operating Temperature

IP Rating

Max Unit Operating Temperature

Occupancy Monitor (optional)

3200W @ 208-240VAC or

00W @ 120VAC

120Vac or 208

-240Vac +/- 10% 50/60Hz

50mA

See below

Momentary or Toggle

-60 minutes

5°C to 25°C

25°C

Must be fitted in Parallel

20°C to 30°C

IP65

65°C

12V dc

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 5

WARNING: Solaira SMaRT 16-DV Variable control is a high-power

electrical device and MUST ONLY BE INSTALLED BY A CERTIFIED

ELECTRICIAN TO LOCAL AND NATIONAL ELECTRICAL CODE

Operating Voltage

Direction

Detection

90° Adjustable

45’ (18 Meters)

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 6

SMaRT 16-DV ILLUSTRATIVE WIRING DIAGRAM*

*Connection diagram is for illustrative purpose only. Installation must be carried out by certified electrician to local,

state/provincial and National Electric Code (NEC) requirements. Inforesight Consumer Products Inc. assumes no responsibility

for the heaters or controller electrical plan or installation.

WARNING SERIOUS INJURY OR DEATH COULD OCCUR,

DISCONNECT ALL POWER PRIOR TO SERVICE

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 7

TROUBLE SHOOTING

Trouble Shooting

Temperature Set Point

Temperature set point allows user to control the

MINIMUM TEMPERATURE for heaters to come on. If the

ambient temperature is above the pre-set level, the

heater control will show "t" and WIL NOT TURN ON. You

can reduce the minimum temperature to 5⁰C

Temperature Sensor Input (Sensor Not Included)

For local temperature sensor input or optional remote

temperature sensor (SMRTVTEM-R) input. The local

temperature sensor is not included with the SMaRT 16-

DV controller. If the user wishes to use a temperature

monitoring feature, simply purchase separately and

connect the temperature sensor.

FLASHING DOT ON CONTROL PANEL DISPLAY

If the controller is used WITHOUT OPTIONAL OCCUPANCY SENSOR (SMRTOCC), then "wire jumper"

must be installed in pins SIG and COM as shown. If the jumper is not installed, the controller senses an

open circuit and will switch OFF. Your controller comes with the jumper installed and it should only be

removed when a sensor is installed.

Wire jumper installed for use

WITHOUT optional Occupancy

SENSOR (PIR)

PLEASE NOTE: If you are using a SMRTOCC with the Solaira SMaRT 16DV and 34DV, the timer

function on the SMaRT Wall Switch SM-WSD will be overridden if the SMRTOCC has been activated.

If you are not using a SMRTOCC, the Link that is fitted as standard between the SIG IN / COM ‘MUST’

be removed otherwise the timer function on the SMaRT Wall Switch SM-WSD will not operate.

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

IOM ▪SMaRT-16DV Rev 2. 11.19.22 8

LIMITATION OF LIABILITY

It is understood and agreed that seller’s liability whether in contract, in tort, under any warranty, in negligence or

otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no circumstances

shall seller be liable for special, indirect or consequential damages. The price stated for the equipment is a consideration

in limiting seller’s liability. No action, regardless of form, arising out of the transactions may be brought by purchaser

more than one year after the cause of action has accrued.

WARRANTY

1. SOLAIRA CONTROL products are guaranteed to be free from mechanical and electrical defects for a period of one

year from date of shipment under normal use and service provided installation is made in accordance with

manufacturers’ recommendations.

2. Parts deemed defective shall be repaired or replaced at manufacturers option and at manufacturers expense but shall

not include foreign or federal excise taxes, state or municipal sale or use taxes, all such taxes not limited to the

foregoing being responsibility of the purchaser.

3. No charge for travel and/or mileage will be allowed to purchaser.

4. SOLAIRA reserves the right to make changes in design or make any improvements on any products. The right is

always reserved to modify our equipment because of new technology, underwriter’s requirements and/or government

regulations.

5. The following are not covered under warranty:

a. INSTALLATION OF CONTROL BY NON-CERTIFIED ELECTRICIAN.

b. Failure from neglect, abuse, careless handling and mis-application of unit.

c. Failure to observe guidelines for installation or improper voltage hook-up.

d. Failure caused by improper installation and not following local, state/provincial and federal electrical guidelines

e. Unless specifically allowed by SOLAIRA CONTROLS, no other charges may be included under warranty.

Notice: Inforesight Consumer Products Inc. website, product information and products can be accessed from Canada and other countries around the

world. Customer understands that some or all products provided by Inforesight Consumer Products Inc. may not be available for purchase or

installation in certain jurisdictions or geographical areas. Inforesight Consumer Products Inc. reserves the right, in its sole discretion, to exclude or

otherwise limit the provision of any product to a person or entity residing in any jurisdiction or geographical area outside of Canada. Inforesight

Consumer Products Inc. provides general product information, installation guidelines and procedures and Customer understands that Customer is

solely and exclusively responsible for installation of the product and ascertaining all applicable local municipal, provincial, state, and federal NEC

(National Electrical Code) rules, by-law, ordinances and guidelines applicable to the installation of any Inforesight Consumer Products Inc. products.

Customer must strictly adhere to and be compliant with the local rules, laws, ordinances and legal requirements for the safe installation and use of

any Inforesight Consumer Products Inc. products. Instruction manuals are included with the product packaging and copies of our instruction

manuals are available upon request. Under no circumstances shall Inforesight Consumer Products Inc. or its affiliated entitles, employees, agents,

shareholders, officers or directors be liable to Customer or any third party for any product installations and Customer releases Inforesight Consumer

Products Inc. from any and all losses, death, personal injury, property damage, other damages, rights, claims, demands and actions of any kind

arising from the Customer’s installation and use of the product, whether the installation was or was not in accord with the provided instruction

manual and/or in compliance with applicable local laws.

Due to ongoing product improvements, specifications and dimensions are subject to change without notice and without incurring obligations.

Solaira°™is a registered trademark of Inforesight Consumer Products Inc.

125 Traders Blvd. # 4, Mississauga, Ontario, Canada, M4Z 2H3

Tel: 905-568-7655, EXT23 SERVIC, Fax:905-568-7521

info@solairaheaters.com

Inhaltsverzeichnis

Andere Solaira Controller Handbücher

Solaira

Solaira SMRTOCC40 Bedienungsanleitung

Solaira

Solaira SMRTOCC60 Bedienungsanleitung

Solaira

Solaira SMaRT 34-DV Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung