Solaira Alpha H3 Bedienungsanleitung

Reference Manual

Solaira Alpha

H3 277V

(3 × Lamp Emitter Heater)

CANADA & USA MODELS:

WEATHERPROOF INFRARED HEATERS SUITABLE FOR OUTDOOR AND INDOOR USE

IN NON-HAZARDOUS AREAS

- COMMERCIAL AND INDUSTRIAL, (RESIDENTIAL 240V OUTDOOR USE ONLY)

Ref No. 043484-EN-S Iss. A

I M P OR TA N T - S AV E T H E S E I N S T R U C T I O N S F O R F U T U R E R E F E R E N C E

INFORESIGHT CONSUMER RODUCTS INC.

125 Traders Blvd. E Unit # 4, Mississauga, Ontario L4Z 2H3

Tel 905-568-7655 - Fax 905-568-7521

Email info@solairaheaters.com - Website www.solairaheaters.com

247748

SALPHA -45277C (240V - 75W / 277V - 4500W)

SALPHA -45277L1C (240V - 75W / 277V - 4500W) CANDEL LOW LIGHT

SALPHA -60277C (240V - 4500W / 277V - 6000W)

SALPHA -60277L1C (240V - 4500W / 277V - 6000W) CANDEL LOW LIGHT

C = COLOR CODE

1. Read all instructions before using this heater.

2. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or

injury to persons.

3. This heater is hot when in use. To avoid burns, do not let bare skin

touch hot surfaces. If provided, use handles when moving this heater.

Keep combustible materials, such as furniture, pillows, bedding,

papers, clothes, and curtains at least 6 feet (1.8m) from the front of the

heater and keep them away from the sides and rear.

4. Extreme caution is necessary when any heater is used by or near

children or invalids and whenever the heater is left operating and

unattended.

5. Do not operate any heater with a damaged cord or after the heater

malfunctions, has been dropped or damaged in any manner. Return

heater to authorized service facility for examination, electrical or

mechanical adjustment, or repair.

6. This heater is not intended for use in bathrooms, laundry areas and

similar locations. Never locate heater where it may fall into a bathtub

or other water container.

7. To disconnect heater, turn controls to off.

WARNING -

Each power supply circuit shall be provided with

disconnecting means and the disconnecting means shall be grouped

together.

I M P O R TA N T I N S T RU C T I O N S

When using electrical INFRARED HEATERS, basic precautions

should always be followed to reduce the risk of fire, electric shock,

and injury to persons, including the following

2 of 16 Ref No. 043484-EN-S Iss. A

8. Do not insert or allow foreign objects to enter any opening as this may

cause an electric shock or fire, or damage the heater.

9. To prevent a possible fire, do not block openings in any manner.

10. A heater has hot parts inside. Do not use it in areas where gasoline,

paint, or flammable liquids are used or stored.

11. Do not cover or otherwise obstruct the heater.

I M P O R TA N T I N S T RU C T I O N S

SAVE THE SE I NST RUCTI ON S

G R O U N D I N G I N S T R U C T IO N S

For 240V / 277V heaters, the cords from each terminal box must be

permanently connected (hard wired).

Kee combustible material such as furniture, a ers,

clothes and curtains at least 6 feet (1.8m) from the front

of the heater and away from the sides and rear.

Heaters are not intended for use as indoor residential or

as a household heater. They may be used for outdoor residential

240V use.

WAR N I NG : R I S K O F F IRE

3 of 16 Ref No. 043484-EN-S Iss. A

I N T R O D U C T I O N

The Alpha H3 heater produces radiant heat like the sun, warming people and objects rather

than the air in between. It is mounted on an adjustable bracket that allows the heat to be

directed exactly where it is required. The Alpha H3 can also be used in a modular system in

that more than one heater can be connected together - see ‘Configurations’ later in the

manual. The Alpha H3 weatherproof heater is designed for indoor and outdoor use.

Please read the following instructions carefully before use. The safety of this heater is

guaranteed only by its correct usage in accordance with these instructions, therefore

they should be retained for future reference.

Before using this appliance

1. Check that the voltage indicated on the units rating label corresponds to the mains

supply voltage.

2. Do not install the heaters less than the minimum height from the floor as specified below

in the specification table.

3. Ensure that the heater has been securely fastened in its final mounting position.

4. WARNING - This appliance must be grounded and hard wired!

5. WARNING - Keep the supply cables away from the front and body of the heater which

will get hot during use.

6. Do not cover or obstruct the heater while it is in use.

7. Do not insert any object through any slot or opening in the heater.

8. Do not use if a grille is not present.

9. When replacing the emitter or cleaning the unit, ensure that the hard wired circuit(s) is

disconnected from the mains supply. Note: always ensure that the lamp emitter is cool

before handling.

10. Do not handle the halogen emitter with bare hands. If it is inadvertently

touched, remove finger marks with a soft cloth and methylated spirit or

rubbing alcohol. Otherwise, the marks will burn into the quartz glass of the

lamp emitter during use causing premature heater failure.

11. The heater is not intended for use by young children and must be supervised

by a responsible person at all times.

C AU T I O N

4 of 16 Ref No. 043484-EN-S Iss. A

5 of 16 Ref No. 043484-EN-S Iss. A

S P E C I F I C AT I O N TA B L E

A l h a H 3 2 4 0 V / 2 7 7 V H e a t e r s

Number of

Units

Model Type

1 - off

SALPHA3-45277C

SALPHA3-45277L1C

1 - off

SALPHA3-60277C

SALPHA3-60277L1C

2 - off

SALPHA3-45277C

SALPHA3-45277L1C

2 - off

SALPHA3-60277C

SALPHA3-60277L1C

Voltage 240V /277V 240V /277V 240V /277V 240V /277V

Number of 3 3 6

Lamp Emitters

Power

1125W /1500W 1500W /2000W 1125W /1500W 1500W /2000W

Total Power

of Unit 3375W /4500W 4500W /6000W 6750W /9000W 9000W /12000W

Current er

Lam Emitter 4.7A /5.4A 6.3A /7.2A 4.7A /5.4A 6.3A /7.2A

Total Current

of Unit 14.1A /16.2A 18.8A /21.7A 28.1A /32.5A 37.5A /43.3A

Minimum Mounting

Height from Floor/

Grade to Bottom of

Heater

7ft 10½in

(240 cm)

8ft 2in

(249cm)

8ft 9in

(267cm)

9ft 6in

(290cm)

9ft 9in

(297cm)

11ft

(330cm)

Minimum Distance

from Ceiling to To

of Heater

7½in

(19cm)

15in

(38cm)

Minimum Distance

from Side Wall to Side

of Heater

36in

(92cm)

33in

(84cm)

34in

(86cm)

39in

(99cm)

43in

(109cm)

49in

(124cm)

51in

(130cm)

59in

(150cm)

Dimensions -

W × H × D

(inc. Bracket &

bars in max. osition)

47½in × 9in × 12¾in

(120cm × 23cm × 32cm)

47½in × 18¼in × 12¾in

(120cm × 46cm × 32cm)

Weight 17.6lb

(8.0kg)

35.4lb

(16.5kg)

7ft 10½in

(240 cm)

6 of 16 Ref No. 043484-EN-S Iss. A

I N S TAL L AT I O N

The heater is fitted with 3 × supply cords measuring 79in (200cm) for hard wiring.

WARNING: Wiring procedures and connections should be in accordance with the National

Electric Code (NEC) and local codes.

WARNING: If the supply cord(s) becomes damaged, it must be immediately replaced by a

qualified person in order to avoid a hazard.

CAUTION: Disconnect electric power supply before working on circuit wiring to prevent electric

shock.

CAUTION:

Please observe the minimum safe distance between the heater body and any

inflammable surfaces.

CAUTION: When the electrical connection is outside weatherproof sockets must be used having

ground fault protection (GFCI or GFI).

NOTE: CONSULT A QUALIFIED ELECTRICIAN, IF IN DOUBT.

C O N F I G U R AT I O N S

The Alpha H3 heater contains three lamp emitters. It can be installed as a single unit or

joined to one other single unit with joining bars that are available to connect the heaters

together and increase the size and output of the installation. The maximum number of Alpha

H3 heaters that can be joined together is two. Please read the section ‘joining heaters

together’ for information on how this should be done.

 The Alpha H3 heater should only be wall

mounted in a horizontal manner or hung from

a ceiling from chains (not supplied).

 When wall mounting the Alpha H3 heater, do

not position the heater at an angle more than

50° and less than 30° as shown in Fig. A.

 When ceiling hanging the Alpha H3 heater,

ensure the minimum distance from the

ceiling is adhered to as shown in Fig. B.

continue over page…

M O U N T I N G - 1 × T R I P L E ( T H R E E L AM P E M I T T E R ) H E AT E R

C A U T I O N

Always isolate the heater from the mains

su ly when mounting or adjusting the

heater osition.

Fig. A

SEE

SPEC.

TABLE

FOR MIN.

HEIGHT

7 of 16 Ref No. 043484-EN-S Iss. A

 Always allow the heater to cool before attempting to

reposition/move. Never attempt to move the heater

while it is switched on!

 Observe the minimum safe distance between the heater

body and inflammable surfaces and objects when

mounting.

 Please refer to the specification table for the

recommended positioning of the heater with regards to

minimum distances. Do not install the heater in a

corner!

 Keep out of the reach of children.

1. When wall mounting, securely fasten the L-shaped

wall brackets to the mounting surface using both of the

fixing holes in the short part of the bracket (see Fig. D for

mounting hole centres). Please refer to the specification

table for recommended positioning of the heater. Please

note. wall fixings are not supplied. They should be

selected to substantially support the weight of the

installation. If in doubt contact a professional for advice!

When hanging from a ceiling two equal length and gauge

chains are required and should be selected with fixings

that are adequate to hold the weight of the heater. Again,

if in doubt contact a professional for advice!

2. The heater should be mounted with the terminal box

at the bottom of the heater when being wall mounted.

3. When wall mounting, fix in the required angular

position by tightening the fixing bolts on the brackets at

the rear of the heater as shown in Fig. C. The heater

should face directly down when hanging.

4. Secure the supply cable so it is not resting on the

body or obstructing the air-vents.

Always isolate the heater from the mains su ly when

adjusting the osition.

DRILLING HOLE TEMPLATE DIMENSIONS FOR WALL MOUNTED BRACKETS

Fig. D

Fig. B

Fig. C

TERMINAL

BOX

SEE SPEC.

TABLE

FOR MIN.

CLEARANCE

Fig. B

8 of 16 Ref No. 043484-EN Iss. A

AS S E M B L I N G -

2 × T R I P L E ( T H R E E L A M P E M I T T E R ) H E AT E R S J O I N E D

1. Take the first heater and place it face down on a flat surface.

2. Take the second heater and place it face down and positioned parallel to the first heater.

3. Push the bolts used to hold the wall brackets through the hole in the brackets on the rear

heaters and slide a shake-proof washer on all the threads from the protruding side.

4. Slide the joining bars on each bolt and fit a washer and nut – do not fully tighten at this

point.

5. Ensure the second heater is still parallel to the first and sitting flat.

Slide the joining bars on each protruding bolt of the other heater to connect them

together and fit the washers and nuts.

7. Again, ensuring the heaters remain flat, fully tighten all four nuts to secure the joining

bars in place.

 When two Alpha H3 heaters are joined they should only be hung from a ceiling on

chains - do not wall mount!

 Always allow the heater to cool before attempting to reposition/move. Never attempt to

move the heater while it is switched on!



Observe the minimum safe distance between the heater body and inflammable

surfaces and objects when mounting.

 Please refer to the specifications table for the

recommended positioning of the heater with

regards to minimum distances. Do not install the

heater in a corner!

 Keep out of the reach of children.

1. When hanging from a ceiling, two chains of

equal length and gauge are required and should

be selected with fixings that are adequate to

hold the weight of the heater. If in doubt contact

a professional for advice!

Continue on next page...

C A U T I O N

Always isolate the heater from the mains su ly when mounting or adjusting the

heater osition.

C H AI N H AN G IN G -

2 × T R I P L E ( T H R E E L AM P E M I T T E R ) H E AT E R S J O I N E D

Fig. E

SEE

SPEC.

TABLE

FOR MIN.

CLEARANCE

9 of 16 Ref No. 043484-EN-S Iss. A

2. Fix the heater assembly to the chains via the hole in the centre of the joining bar as

shown in Fig. E. and ensure the heaters face directly down when hanging.

3. Secure the supply cable so it is not resting on the body or obstructing the air-vents.

Always isolate the heater from the mains su ly when adjusting the osition.

Fig. F

Fig. G

C I R C U I T D I A G R AM 2 4 0 V S U P P LY

277V HEATER RATED ON 240V SUPPLY

277V RATED HEATER CONNECTED

ON STAR/WYE OUTPUT

(NEUTRAL TO PHASE)

C I R C U I T D I A G R AM 2 7 7 V S U P P LY

10 of 16 Ref No. 043484-EN-S Iss. A

M AI N T E N AN C E ( 2 7 7 V C I R C U I T )

CAUTION: Unplug/Switch off unit from the mains supply before replacing a lamp emitter

or any maintenance procedure including cleaning.

CAUTION: Should dust or dirt appear on the reflectors, it is recommended that that the

wire grilles and lamp emitters are removed and the reflectors are wiped with a lint-free

cloth before reassembling (see lamp emitter replacement instructions).

NOTE: For re lacement lam emitters or s are arts lease contact your local

distributor quoting model ty e and rating from rating label. It is very im ortant that

your re lacement lam emitters are exactly the same as the one it was su lied

with. Failure to fit the exact same ty e can cause the heater to rematurely fail.

CAUTION: Please ensure that the length of wires on the replacement lamp emitter are the same

as shown in the diagram below (Fig. H).

Y O U R R E P LA C E M E N T L A M P E M I T T E R

Fig. H

[13.976in]

355mm MAX.

[17.976in]

375mm MAX.

[17.976in]

375mm MAX.

Andere Solaira Heizung Handbücher

Solaira

Solaira Cosy XL Double Bedienungsanleitung

Solaira

Solaira ICR H3 Series Bedienungsanleitung

Solaira

Solaira SALPHA15120 Bedienungsanleitung

Solaira

Solaira SCOMH01500 Gebrauchs- und Pflegehandbuch

Solaira

Solaira Alpha H1 Bedienungsanleitung

Solaira

Solaira Cosy XL Bedienungsanleitung

Solaira

Solaira Alpha H2SALPHAH2-20240 Bedienungsanleitung

Solaira

Solaira Cosy SCOSYAW15120 Bedienungsanleitung

Solaira

Solaira ICR Series Bedienungsanleitung

Solaira

Solaira Cosy XL Bedienungsanleitung

Solaira

Solaira SCOSYXLAW15120 Bedienungsanleitung

Solaira

Solaira SALPHAH3-30240 Bedienungsanleitung

Solaira

Solaira Malibu MAL 45240 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung