SolarEast BLN-006TB1 Bedienungsanleitung

BLN-006TB1/BLN-010TB1/BLN-014TB1/BLN-018TB1

BLN-010TB3/BLN-014TB3/BLN-018TB3/BLN-024TB3

Please read this manual carefully before using it and keep it in a safe place

Heat Pump for Heating & Cooling & DHW

Air Source Heat Pump

R32

1. Please read the instruction manual carefully before installation or operation.

2. The heat pump must be installed by a professional installer.

3. Please follow the instruction manual strictly when installing the heat pump

4. If any update on the product, this instruction manual is subject to change without notice

5. If the heat pump is installed where is vulnerable to lightning strikes, it is necessary to take lightning

protection measures; if the heat pump is turned off in the winter, please be sure to drain the water

in the system to prevent cold water from swelling and causing system damage.

User Instruction-------------------------------------------------------------------1

Operation Instructions----------------------------------------------------------8

Dimension-------------------------------------------------------------------------15

Installation------------------------------------------------------------------------17

Commissioning and Maintenance ---------------------------------------28

Trouble Analysis-----------------------------------------------------------------30

Specification----------------------------------------------------------------------34

After-sale Service----------------------------------------------------------------36

Controller Supplement--------------------------------------------------------37

Note

Content

1. Precautions

Please make sure that you have read this manual before using our air source heat pump. In the

“User Information” chapter, “User Information” provides essential safety information. Please be

sure to follow the instruction strictly.

User Instructions

Please use an electrical leakage switch,

otherwise, there may be electric shock, fire, etc.

Test Button

2. Make sure that the leakage protection switch

is securely connected. If the wiring is not secure,

it may cause electric shock, heat, or fire.

3. Do not operate with a wet hand,

otherwise, there may cause electric

shock.

4. Do not insert your fingers or any stick into

the

inside of the ventilation area, otherwise,

harm

will

caused.

Dange

Warning

Wrong operations are likely to cause serious consequences such as death, serious

injury, or major accidents

Improper operation may result in a safety accident, damage to the machine, or affect

the function of the machine.

Note

1) This Machine is not allowed to be installed by the user. A professional installer must install it,

Otherwise cause safety accidents or affects the machine’s performance.

2) Without professional guidance, non-professionals are not allowed to disassemble the machine.

Otherwise, accidents or damage may be caused to the device.

3) Do not use or store flammable materials such as hair spray, paint, gasoline, alcohol, etc., around

the machine. Otherwise, fire may be caused.

4) The machine’s main power switch should be placed where that child cannot reach to prevent

children from playing with the power switch.

5) Do not spray water or other liquids on the machine. Otherwise, danger may occur.

6) Do not touch the machine with wet hands. Otherwise, it may cause an electric shock.

7) In thunderstorms, please disconnect the main power switch off the machine. Otherwise, lightning

may cause danger or damage to the device.

8) The machine needs to use a separate power switch to avoid sharing the same circuit with other

electrical appliances, supply the power to the machine vice the specified power cable, and use

the proper breaker with the electric leakage protection required.

9) The machine must be installed with a specified grounding wire. Do not connect the grounding

wire to the gas pipe, water pipe, lightning conductor, or telephone, and the machine must be

grounded reliably to avoid any electric shock.

10) Do not disconnect the power supply when the machine is running.

11) When the machine is not used for a long time, please disconnect the main power switch to avoid

accidents.

12) If the ambient temperature is below 0 ℃, it is forbidden to cut off the power supply. If the power

is turned off unexpectedly under these conditions, drain the water inside the pipeline.

1) Do not put your hands or other objects into the air outlet of the machine. Otherwise, the fan

running at high speed may cause harm.

2) Do not remove the fan cover. Otherwise, the fan running at high speed may cause injury to you

or others.

3) Lightning and other sources of electromagnetic radiation may have a remarkable effect on the

machine. Turn off the power and then restart the device if it does affect it.

4) Make sure the water supply is frequent. Otherwise, the machine may be damaged.

5) Do not restart the machine frequently. Otherwise, the device may be damaged.

6) The operating parameters of the machine and the set value of the protection device have been

selected by the manufacturer. Users should not change the set value arbitrarily and do not short

the wire of the protection device. Otherwise, the machine may be damaged due to improper

protection.

7) To avoid the freezing of the water system pipeline when the machine is deactivated in an

environment below 0 ℃, please keep the machine standby state. If the device is out of service

Please read the labels on the machine carefully. If abnormal conditions such as abnormal noise, odor, smoke,

temperature rise, electric leakage, fire, etc. are found during use, please cut off the power immediately and

contact our local customer service center or dealer in time to repair it. Contact the local fire and emergency

department immediately if necessary.

Warning

Note

for a long time, it is recommended that the user drain the water out of the water system and

disconnect the power supply.

8) Please perform regular maintenance on the machine as required by the instructions to ensure the

device is in good operating condition.

2. Refrigerant Precaution

1) Do not use means to accelerate the defrosting process or to clean, other than those

recommended by the manufacturer.

2) The appliance shall be stored in a room without continuously operating ignition sources (for

example open flames, an operating gas appliance, or an operating electric heater)

3) Do not pierce or burn.

4) Be aware that refrigerants may not contain an odor.

5) Appliance shall be installed, operated, and stored in a room with a floor area larger than X

6) The installation of pipe-work shall be kept to a minimum of X m2

7) Spaces where refrigerant pipes shall be in compliance with national gas regulations.

8) Servicing shall be performed only as recommended by the manufacturer.

9) The appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as specified for operation.

10) All working procedures that affect safety means shall only be carried out by competent

persons.

3. Requirement of Flammable Refrigerant

1) Transport of equipment containing flammable refrigerants: Compliance with the transport

regulations

2) Marking of equipment using signs: Compliance with local regulations

3) Disposal of equipment using flammable refrigerants: Compliance with national regulations

4) Storage of equipment/appliances: The storage of equipment should be in accordance with the

manufacturer’s instructions.

5) Storage of packed (unsold) equipment: Storage package protection should be constructed such

that mechanical damage to the equipment inside the package will not cause a leak of the

refrigerant charge. The maximum number of pieces of equipment permitted to be stored together

will be determined by local regulations.

6) Information on servicing:

i. Checks to the area

Prior to beginning work on systems containing flammable refrigerants, safety checks are

necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating system,

the following precautions shall be complied with prior to conducting work on the system.

ii. Work Procedure

Work shall be undertaken under a controlled procedure so as to minimize the risk of flammable

gas or vapor being present while the work is being performed.

iii. General Work Area

All maintenance staff and others working in the local area shall be instructed on the nature of

the work being carried out. Work in confined spaces shall be avoided. The area around the

workspace shall be sectioned off. Ensure that the conditions within the area have been made

safe by control of flammable material.

iv. Checking for the presence of refrigerant

The area shall be checked with an appropriate refrigerant detector prior to and during work, to

ensure the technician is aware of potentially flammable atmospheres. Ensure that the leak

detection equipment being used is suitable for use with flammable refrigerants, i.e. non-

sparking, adequately sealed or intrinsically safe.

v. Presence of fire extinguisher

If any hot work is to be conducted on the refrigeration equipment or any associated parts,

appropriate fire extinguishing equipment shall be available to hand. Have a dry powder or CO2

fire extinguisher adjacent to the charging area.

vi. No ignition sources

No person carrying out work in relation to a refrigeration system that involves exposing any

pipework that contains or has contained flammable refrigerant shall use any sources of ignition

in such a manner that it may lead to the risk of fire or explosion. All possible ignition sources,

including cigarette smoking, should be kept sufficiently far away from the site of installation,

repairing, removal, and disposal, during which flammable refrigerant can possibly be released

to the surrounding space. Prior to work taking place, the area around the equipment is to be

surveyed to make sure that there are no flammable hazards or ignition risks. “No Smoking”

signs shall be displayed.

vii. Ventilated area

Ensure that the area is in the open or that it is adequately ventilated before breaking into the

system or conducting any hot work. A degree of ventilation shall continue during the period

that the work is carried out. The ventilation should safely disperse any released refrigerant and

preferably expel it externally into the atmosphere.

viii. Checks to the refrigeration equipment

Where electrical components are being changed, they shall be fit for the purpose and to the

correct specification. At all times the manufacturer’s maintenance and service guidelines shall

be followed. If in doubt consult the manufacturer’s technical department for assistance. The

following checks shall be applied to installations using flammable refrigerants:

--The charge size is in accordance with the room size within which the refrigerant containing

parts are installed;

--The ventilation machinery and outlets are operating adequately and are not obstructed;

--If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the

presence of refrigerant;

--Marking of the equipment continues to be visible and legible. Markings and signs that are

illegible shall be corrected;

--Refrigeration pipes or components are installed in a position where they are unlikely to be

exposed to any substance which may corrode refrigerant-containing components unless the

components are constructed of materials that are inherently resistant to being corroded or are

suitably protected against being so corroded.

ix. Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks and

component inspection procedures. If a fault exists that could compromise safety, then no

electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault

cannot be corrected immediately but it is necessary to continue operation, an adequate

temporary solution shall be used. This shall be reported to the owner of the equipment so all

parties are advised.

Initial safety checks shall include:

• That capacitor is discharged: this shall be done in a safe manner to avoid the possibility of

sparking;

• That there no live electrical components and wiring are exposed while charging, recovering,

or purging the system;

• That there is continuity of earth bonding.

7) Repairs sealed components:

a) During repairs to sealed components, all electrical supplies shall be disconnected from the

equipment being worked upon prior to any removal of sealed covers, etc. If it is absolutely

necessary to have an electrical supply to equipment during servicing, then a permanently

operating form of leak detection shall be located at the most critical point to warn of a

potentially hazardous situation.

b) Particular attention shall be paid to the following to ensure that by working on electrical

components, the casing is not altered in such a way that the level of protection is affected. This

shall include damage to cables, an excessive number of connections, terminals not made to

original specification, damage to seals, incorrect fitting of glands, etc. Ensure that apparatus is

mounted securely. Ensure that seals or sealing materials have not degraded such that they no

longer serve the purpose of preventing the ingress of flammable atmospheres. Replacement

parts shall be in accordance with the manufacturer’s specifications.

NOTE: The use of silicone sealant may inhibit the effectiveness of some types of the leak.

8) Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that

this will not exceed the permissible voltage and currently permitted for the equipment in use.

Intrinsically safe components are the only types that can be worked on whillivingve in the

presence of a flammable atmosphere. The test apparatus shall be at the correct rating. Replace

components only with parts specified by the manufacturer. Other parts may result in the ignition

of refrigerant in the atmosphere from a leak.

9) Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects. The check shall also take into account the

effects of aging or continual vibration from sources such as compressors or fans.

10) Detection of flammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or

detection of refrigerant leaks. A halide torch (or any other detector using a naked flame) shall not

be used.

11) Leak detection methods

The following leak detection methods are deemed acceptable for systems containing flammable

refrigerants.

Electronic leak detectors shall be used to detect flammable refrigerants, but the sensitivity may

not be adequate or may need re-calibration. (Detection equipment shall be calibrated in a

refrigerant-free area.) Ensure that the detector is not a potential source of ignition and is suitable

for the refrigerant used. Leak detection equipment shall be set at a percentage of the LFL of the

refrigerant and shall be calibrated to the refrigerant employed and the appropriate percentage of

gas (25 % maximum) is confirmed.

Leak detection fluids are suitable for use with most refrigerants but the use of detergents

containing chlorine shall be avoided as the chlorine may react with the

refrigerant and corrode the copper pipe-work.

12) Removal and evacuation

When breaking into the refrigerant circuit to make repairs – or for any other purpose –

conventional procedures shall be used. However, it is important that best practice is followed

since flammability is a consideration. The following procedure shall be adhered to:

• Remove refrigerant;

• Purge the circuit with inert gas;

• Evacuate;

• Purge again with inert gas;

• Open the circuit by cutting or brazing.

The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be

“flushed” with OFN to render the unit safe. This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to fill

until the working pressure is achieved, then venting to the atmosphere, and finally pulling down

to a vacuum. This process shall be repeated until no refrigerant is within the system. When the

final OFN charge is used, the system shall be vented down to atmospheric pressure to enable work

to take place. This operation is absolutely vital if brazing operations on the pipe-work are to take

place.

Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is

ventilation available.

13) Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed.

--Ensure that contamination of different refrigerants does not occur when using charging

equipment. Hoses or lines shall be as short as possible to minimize the amount of

refrigerant contained in them.

--Cylinders shall be kept upright.

--Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

--Label the system when charging is complete (if not already).

--Extreme care shall be taken not to overfill the refrigeration system.

--Prior to recharging the system, it shall be pressure tested with OFN. The system shall be leak

tested on completion of charging prior to commissioning. A follow-up leak test shall be carried

out prior to leaving the site.

14) Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with

the equipment and all its detail. It is recommended good practice that all refrigerants are

recovered safely. Prior to the task being carried out, an oil and refrigerant sample shall be taken

in case analysis is required prior to re-use of reclaimed refrigerant. It is essential that electrical

power is available before the task is commenced.

a) Become familiar with the equipment and its operation.

b) Isolate system electrically.

c) Before attempting the procedure ensure that:

• Mechanical handling equipment is available, if required, for handling refrigerant cylinders;

• All personal protective equipment is available and being used correctly;

• The recovery process is supervised at all times by a competent person;

• Recovery equipment and cylinders conform to the appropriate standards.

d) Pump down refrigerant system, if possible.

e) If a vacuum is not possible, make a manifold so that refrigerant can be removed from various

parts of the system.

f) Make sure that cylinder is situated on the scales before recovery takes place.

g) Start the recovery machine and operate in accordance with manufacturer's instructions.

h) Do not overfill cylinders. (No more than 80 % volume liquid charge).

i) Do not exceed the maximum working pressure of the cylinder, even temporarily.

j) When the cylinders have been filled correctly and the process completed, make sure that the

cylinders and the equipment are removed from the site promptly and all isolation valves on the

equipment are closed off.

k) Recovered refrigerant shall not be charged into another refrigeration system unless it has been

cleaned and checked.

15) Labelling

Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant.

The label shall be dated and signed. Ensure that there are labels on the equipment stating the

equipment contains flammable refrigerant.

16) Recovery

When removing refrigerants from a system, either for servicing or decommissioning, it is

recommended good practice that all refrigerants are removed safely. When transferring

refrigerant into cylinders, ensure that only appropriate refrigerant recovery cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge is

available. All cylinders to be used are designated for the recovered refrigerant and labeled for that

refrigerant (i.e. special cylinders for the recovery of refrigerant). Cylinders shall be complete with

a pressure relief valve and associated shut-off valves in good working order. Empty recovery

cylinders are evacuated and, if possible, cooled before recovery occurs. The recovery equipment

shall be in good working order with a set of instructions concerning the equipment that is at hand

and shall be suitable for the recovery of flammable refrigerants. In addition, a set of calibrated

weighing scales shall be available and in good working order. Hoses shall be complete with leak-

free disconnect couplings and in good condition. Before using the recovery machine, check that

it is in satisfactory working order, has been properly maintained, and that any associated electrical

components are sealed to prevent ignition in the event of a refrigerant release. Consulting

manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery

cylinder, and the relevant Waste Transfer Note arranged. Do not mix refrigerants in recovery units

and especially not in cylinders. If compressors or compressor oils are to be removed, ensure that

they have been evacuated to an acceptable level to make certain that flammable refrigerant does

not remain within the lubricant. The evacuation process shall be carried out prior to returning the

compressor to the suppliers. Only electric heating to the compressor body shall be employed to

accelerate this process. When oil is drained from a system, it shall be carried out safely.

4. Other Safety

Thank you for choosing a heat pump. This is a heat pump capable of providing the ideal comfort for

your home, always with a suitable hydraulic installation. The unit is an air source heat pump for

space heating/cooling and a sanitary water heater for houses, apartment blocks, and small industrial

premises. Outdoor air is used as a heat source creating free energy to heat your home.

This manual forms an essential part of the product and it must be given to the user. Read the

warnings and recommendations in the manual carefully, as they contain important information on

the safety, use, and maintenance of the installation.

This heat pump must be installed by qualified personnel only, in accordance with the legislation in

force and following the manufacturer’s instructions.

The start-up of this heat pump and any maintenance operations must be carried only by qualified

personnel only.

Incorrect installation of this heat pump could result in damage to people, animals or property, and

the manufacturer will not be held liable in such cases.

The following safety precautions should always be taken into account:

1) Be sure to read the following WARNING before installing the unit.

2) Be sure to observe the cautions specified here as they include important items related to safety.

3) After reading these instructions, be sure to keep them in a handy place for future reference.

4) Equipment shall contain the following identification:

Inflammable “ ” Read Carefully “ ” Professional Recycling “ “

1. Control Panel

2. Operation Instruction

Operation Instruction

Timer

Power ON/OFF

Heating/Cooling/DHW

Change Mode

Water Temperature

Current Mode

Down

Temperature Setting

Time or fault display area

Long press 2s to turn off

the heat pump

When the lock symbol is

displayed, press and

hold 5s to unlock the

screen

Long press 2s to turn on

the heat pump

Power On/Off

Press M to switch mode

Cooling/Heating/DHW

Mode Setting

Andere Handbücher für BLN-006TB1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SolarEast Wärmepumpe Handbücher

SolarEast

SolarEast BLN-006TB1 Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung