Solaris basic 18 Bedienungsanleitung
USER MANUAL
SOLARIS® BASIC 18™ 2
INDEX PAGE NO.
SAFETY INFORMATION 3-4
INTRODUCTION 5
INSTALLATION 6
AC POWER 7
FIXTURE OVERVIEW 8
DMX DATA LINK 9
CONNECTING AND USING DMX DATA LINK 10
FIXTURE OPERATION 10-11
TOKENS 11
FIXTURE MENU STRUCTURE CHART 12
DMX MODES CHARTS 13
MAINTENANCE 14
BASIC 18 SPECIFICATIONS 15-16
INCLUDED ITEMS 16
TABLE OF CONTENTS
3SOLARIS® BASIC 18™
WARNING!
Read the safety precauons in this manual before installing
operang or servicing this product.
SAFETY NOTES
Read all the following Safety Notes before working with this product.
These notes include important informaon about the installaon, us-
age, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to ser-
vicing in this User Manual will only apply to properly trained GLOW®
Professional cered technicians. Do not open the housing or aempt
any repairs.
All applicable local codes and regulaons apply to proper installaon of
this product.
PERSONAL SAFETY
· Avoid direct eye exposure to the light source while the product is on.
· Always disconnect this product from its power source before servicing.
· Always connect this product to a grounded circuit to avoid the risk of
electrocuon.
· Do not touch this product’s housing during operaon because it may
be very hot.
MOUNTING & RIG-
GING
· This product is for indoor use only! To prevent risk of re or
shock, do not expose this product to rain or moisture. (IP20)
· Mount this product in a locaon with adequate venlaon, at least 20
in (50 cm) from adjacent surfaces.
· Make sure there are no ammable materials close to this
product while it is operang.
· Always carry this product by the handles. Do not carry from the head.
· When hanging this product, always secure to a fastening device using
a safety cable.
SAFETY INFORMATION
SOLARIS® BASIC 18™ 4
POWER & WIRING
· Always make sure you are connecng this product to the proper volt-
age in accordance with the specicaons in this manual or on the prod-
uct’s specicaon label.
· Never connect this product to a dimmer pack or any rheostat.
· Never disconnect this product
OPERATION
· Do not operate this product if you see damage to the housing, lenses,
LED lights or cables. Have the damaged parts replaced by an authorized
technician at once.
· Do not cover the venlaon slots when operang to avoid internal
overheang.
· Do not aim this product toward the Sun. The lenses could concentrate
the solar energy and cause internal overheang.
· The maximum ambient temperature is 120 °F (49 °C). Do not operate
this product at a higher temperature.
· In case of a serious operang problem, stop using this product imme-
diately
In the unlikely event that your GLOW® product may require service, contact GLOW®
Technical Support.
5SOLARIS® BASIC 18™
The SOLARIS® Professional BASIC 18™ is a high-performance 18 X 1W RGB Par lighng x-
ture. Its compact design makes it ideal for Venue Installaons and Indoor Use.
The xtures is deemed for its bright 1W LED with a slim design and provides a budget
friendly soluon for rental use and installaons.
A Narrow 15 degrees angel making the xture ideal for object illuminaon which can be per-
fect for special lighng and long distance lighng needs.
The use of RGB 1W LED allows you to reach a variety of color tones and to be able to move
smoothly between dierent color selecons.
The xture can be controlled using any DMX-compliant controller (6 Channel Mode) as well
as automac operaon mode , sound to light mode and manual mode.
BEFORE USING THE PRODUCT FOR THE FIRST TIME
1. Read ’Safety informaon’ on page 3 before installing, operang or servicing the xture.
2. Unpack and ensure that there is no transportaon damage before using the xture. Never
aempt to operate a damaged xture.
3. If the xture is not going to be hard-wired to a mains supply, aach a local power plug to
the end of the supplied power cable.
4. Before operang, ensure that the voltage and frequency of the power supply match the
power requirements of the xture.
5. Refer to the GLOW® website for the most recent user documentaon and technical infor-
maon about this xture.
INTRODUCTION
SOLARIS® BASIC 18™ 6
INSTALLATION
The xture is designed for indoor use only and must be used in a dry locaon with adequate
venlaon. Ensure that none of the xture’s venlaon slots are blocked and ensure that the
xture is fastened to a secure structure or surface. Do not use the xture to illuminate sur-
faces less than 8 m (approx 26.) from the xture.
FASTENING THE FIXTURE TO A FLAT SURFACE
The xture can be fastened to a hard, xed, at surface that is oriented at any angle. Ensure
that the surface and all fasteners used can support at least 10 mes the weight of all xtures
and equipment they will support. Fasten the xture Securely. Do not place it on a surface or
leave it where it can be moved or fall over. If you install the xture in a locaon where it may
cause injury or damage if it falls, secure it as directed below with a securely anchored safety
cable that will hold the xture if the primary fastening method fails.
MOUNTING THE FIXTURE ON A TRUSS
The xture can be clamped to a truss or similar rigging structure in any orientaon. When
installing the xture hanging vercally down, you can use an open-type clamp such as a
G-clamp. When installing in any other orientaon, you must use a half-coupler clamp
that completely encircles the truss or pipe circumference. To clamp the xture to a truss:
1. Check that the rigging structure can support at least 10 mes the weight of all xtures and
equipment to be installed on it.
2. Block access under the work area.
3. Working from a stable plaorm, hang the xture on the
truss and fasten the rigging clamps onto the truss.
4. Secure the xture with a safety cable as directed below.
5. Check that the head will not collide with other xtures or objects.
SECURING WITH A SAFETY CABLE
Secure the xture with a safety cable (or other secondary aachment) that is approved for
the weight of the xture so that the safety cable will hold the xture if a primary aachment
fails. Loop the safety cable through and around a secure metal anchoring point.
WARNING! READ SAFETY INFORMATION ON
PAGE 3 BEFORE INSTALLING THE FIXTURE.
7SOLARIS® BASIC 18™
Socket outlets or external power switches used to supply the xture with power must be
located near the xture and easily accessible so that the xtures can easily be
disconnected from power.
Do not insert or remove power cable to apply or cut power, as this may cause arcing at the
terminals that will damage the connectors.
Do not use an external dimming system to supply power to the xture, as this may cause
damage to the xture that is not covered by the product warranty.
The xture can be hard-wired to a building electrical installaon if you want to install it
permanently, or a power plug (not supplied) that is suitable for the local power out- lets
can be installed on the power cable.
If you replace power plug on the power cable, install a grounding type (earthed) plug with
integral cable grip that is rated minimum 250 V, 5 A.
The xture has an auto-ranging power supply that accepts AC mains power at
100-240 V at 50/60 Hz. Do not apply AC mains power at any other voltage or
frequency to the xture.
Warning! Read ‘Safety informaon’ on page 3 before
connecng the xture to AC mains power.
For protecon from electric shock, the xture must be grounded (earthed). The
power distribuon circuit must be equipped with a fuse or circuit breaker and
ground-fault (earth-fault) protecon.
AC POWER
SOLARIS® BASIC 18™ 8
1Tokens® – symbol indicang the xture DMX personality, Beam Angle, Weight and
Power Supply
2Power input
3DMX data Link Input and Output XLR Connectors
4Digital Screen for accessing menu with 4 buons for navigaon: Menu, Up, Down
and Enter
UP Press UP to change current value
DOWN Press DOWN to change current value
MENU Press MENU to toggle between modes
ENTER Use ENTER to save the parameter aer you made the
desires adjustments
2
1
3
4
FIXTURE OVERVIEW
3
9SOLARIS® BASIC 18™
DMX DATA LINK
A DMX 512 data link is required in order to control the xture via DMX. The xture
has 3-pin XLR connectors for DMX data input and output. The number of daisy-chained
xtures is limited by the number of DMX channels required by the xtures in relaon to
the maximum 512 channels available in one DMX universe. Note that if independent con-
trol of a xture is required, it must have its own DMX channels.
Fixtures that are required to behave idencally can share the same DMX address and
channels. To add more xtures or groups of xtures when the above limit is reached, add
a DMX universe and another daisy-chained link.
CONNECTING AND USING DMX DATA LINK
To connect the xture to data:
1. Connect the DMX data output from the controller to the rst xture’s male XLR
DMX input connector.
2. Connect the rst xture’s DMX output to the DMX input of the next xture and conn-
ue connecng xtures output to input.
SOLARIS® BASIC 18™ 10
FIXTURE OPERATION
This secon explains the xture sengs and ulies that the user has access
to when using the control panel. Sengs are retained when the xture is pow-
ered o. The SOLARIS® BASIC 18™ can funcon in dierent modes:
DMX 6 CHANNEL MODE. When operated in DMX 8 channel mode the xture
back screen will show d001 when rst accessed. By seng a value dierent
from 001 you can change the unit’s DMX address according to your lighng
setup. Oponal DMX address values are 1 to 512. When you reach the desired
value, press ENTER to save your changes.
It is also possible to use 8 predened factory colors, when rst accessing pre-
dened colors back screen will show Au01 when rst accessed. By seng a
value dierent from 01 you can scroll between the 8 Predened factory col-
ors. When you reach the desired color, press ENTER to save your changes.
Automac color blending eect is also available
Color Jump Change (Au09). when using this opon the xture will jump
through the 8 predened colors (Au01-Au08)
Inhaltsverzeichnis
Andere Solaris DJ-Equipment Handbücher
Beliebte DJ-Equipment Handbücher anderer Marken
thomann
thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung
Eagletone
Eagletone 6 Eyes Flower Bedienungsanleitung
EuroLite
EuroLite FLD-1508 Bedienungsanleitung
Technical Pro
Technical Pro LG8xSEA Bedienungsanleitung
JB Systems
JB Systems Lounge Laser DMX Bedienungsanleitung
Lightmaxx
Lightmaxx Vega Halo 90 Bedienungsanleitung
Elation
Elation FUZE WASH Z350 Bedienungsanleitung
Maverick
Maverick MK3 WASH Bedienungsanleitung
Infinity
Infinity TF-260C7 Fresnel Bedienungsanleitung
Chauvet
Chauvet EVE E-50Z Bedienungsanleitung
Eliminator Lighting
Eliminator Lighting E 138 Bedienungsanleitung
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung