Sole Control Remotes SC230 Bedienungsanleitung
Info-lgine
SANS FRAIS
I-800-962-3986
---
SC230
FOR CD
(SC 241 Not Shown)
SOLE
CONTROL
SC230
SC240
SC24l
l SOLE
;
CONTROL
Une
division
de Recoton Corp.
2950 Lake Emma Road, Lake Mary, FL 32746
c1996
par Recoton Corp.
Les
specifications
peuvent
changer sans
preavis
CONSERVE2 POUR
REFERENCE
ULTERlEURE
Part No. 2425-1746
Important Note 13
A short introduction to your new
remote.
Key
Diagram
14
Get to know your Sole control’s
buttons.
Power Up!
14
Shows how to install the batteries.
TV
Set-up .
15
Following
these steps makes Set-UP
simple.
VCR Set-up
16
Easy-to-follow
programming
instructions.
cable Set-up
17
Set your Sole Control to eliminate
that costly cable remote.
CD Set-Up . .
18
For
the SC240 model Only.
CD Key Diagram .
19
For
the SC240 model Only
Sleep Timer
20
Your SC240 can turn Off your TV
automatically
Special Features.
20
Adjust the volume of the TV while
using the VCR keys.
Code
Finder Mode
21
scan the sole Control’s code library
to find the code you need.
TROUBLESHOOTING
22
Helpful hints if you need them.
SMART
LITE
Instructions
23
Turn the keypad light off and on.
Warranty Information
23
Important note for new owners.
Thank you for purchasing a Sole
Control remote.
Right now, your
remote will not work any device.
YOU will need to program the
remote once you install the
batteries.
TO program the remote, you will
need to find the three-digit code
number for your device and brand
in the Code Book (manual
#2).
There
is probably more than one code
listed, but one of them should
operate your component.
It is important to know that the
first code listed isn’t necessarily
the one that works your
component. Try
all the
manufacturer’s codes for the one
that best operates your component.
Keep entering the codes in the
remote following the instructions
(found on the next
few
pages).
The Sole control should work
exactly as your original remote did.
Enjov!
If you have any problems please Call
a customer service representative
at the Sole Control
InfoLine
toll free
at
1-800-962-3986.
13
Key Diagram
VCR MODE KEY
I
INDICATOR
, POWER KEY
1
TV MODE KEY
\
CD MODE KEY
_
(ON SC.240 ONLYI
POWER UP!
VOLUME
tf-
KEY
1.
On the back of the
Sole Control. slide the
battery cover off in the
direction of the arrow. MU1
2. Install 2
“AAA”
TV/VCR KEY
(
batteries, making sure
the + and
-
marks match
the diagram inside.
3.
Replace the battery cover.
4. Test batteries
by pressing
the “Xtra” key (in lower right
corner) and make sure green
light comes on above the
“Power” key. (Improperly
installed batteries may cause
acid leakage and/or damage to
your
SC*230,
SC.240 or
S0241.1
NOTE: When you replace dead
batteries or take them out, you
will need to reprogram your Sole
Control.
14
CABLE MODE KEY
FAST
FORWARD KEY
PAUSE KEY
;-
STOP KEY
-
CHANNEL
tl-
KEY
I
?
RECALL KEY
O-9 NUMBER
KEYS
i
XTRA KEY
The
SC*230
has the capability of
operating up to 3 devices: “TV”,
“VCR”, and
“CBL”.
The
SC@240
and
SC*241
add the ability to operate
a fourth device, “CD”.
TV
set-up:
1.
Turn on your TV. In manual
#2,
find the
3-digit
Code
numbers
for your TV brand.
2. Press
“Xtra”
key.
The green light will come on.
3. Press “TV” key.
The green light will blink once to indicate
that the component has been selected.
a
q
4.
Within thirty seconds,
enter in a
3-digit
code number.
The green light will flash when each code number is
entered correctly. After the last number is entered, the
_
light will blink multiple times to indicate that a valid code
has been programmed into the remote, and then remain
Off.
EL!
5. Test code by pressing “Power” key.
If the TV comes on,
you’ve got the right code. If it doesn’t, return to step 2
and use the next
3-digit
code listed.
q-
NOTE: If none of the codes turn your TV on, try the code finder mode
(page
21).
15
r--l
VCR set-up:
1. Turn on vour TV and VCR and insert a tape. In manual
#2,
find
thej-digit
code numbers
for your VCR brand.
Press
“Xtra”
key. The green light will come on.
4. Within thirty seconds,
enter in a
3-digit
code number.
The green light will flash when code is entered correctly.
!I!!!
5. Test code by pressing “Power” key.
If the VCR turns off,
you’ve found the right code. If it doesn’t, return to step 2
_
and use the next 3-digit code listed.
*m
NOTE: If none of the codes turn your VCR on,
trv
the code finder mode
(page 21).
If you’ve programmed your TV code already and want to operate it now,
press TV key.
16
CABLE set-up:
1. Turn on your TV and cable box. In manual
#2,
find the
3-
digit code numbers
for your cable box brand.
2.
Press
“Xtra”
key.
The green light will come on.
4. Within thirty seconds,
enter in a
3-digit
code number.
The green light will flash when code is entered correctly.
I!!
5. lest code by pressing “Power” key.
If the cable box turns
off, you’ve found the right code. If it doesn’t, return to
step 2 and use the next 3-digit code listed.
em
NOTE: If none of the listed codes work your box, try the code finder mode
(page
21).
If
you’ve already programmed your TV or VCR and want to operate it now,
press “TV” or “VCR”. 17
I
4.
Within thirty seconds,
enter in a
3-digit
Code
number.
The green light will flash when code is entered correctly.
5.
Test code by pressing “Power” key.
If the CD player turns
off, you’ve found the right code. If it doesn’t, return to
step 2 and use the next
3-digit
code listed.
NOTE: If none of the listed codes work your CD player, try the code finder
mode (page
21).
If you’ve already programmed your TV, cab/e, or VCR
ancl
want to Operate it
now, press “TV”, CBL
“,
or “VCR”.
18
CD
set-up:
I. Turn on your CD player and insert a CD. In
manUal#2,
find
the
3-digit
code numbers
for your CD player brand.
2. Press
“Xtra”
key. The green light will come on.
3. Press “CD” key.
DIAGRAM INDICATES
KEY FUNCTIONS AS
THEY RELATE TO
CD PLAYER KEYS.
REWIND (SEARCH
POWER (OPEN/CLOS
FFWD (SEARCH
;E)
k
PAUSE KEY
STOP KEY
L
CHANNEL
/
TRACK O-9
NOTE: “VOLUME”, “MUTE”
&
“RECORD” will not operate in
the CD mode.
19
SLEEP/TIMER FUNCTION
(SC.240
&
SC*2411
Your
SC.240
or SC.241 is
equipped and programmed with
a SLEEP/TIMER function,
SePatXf?
from your TV or
for
a TV not
equipped with SLEEP/TIMER.
1.
Press “Xtra”.
2. Press “TV” key.
3. Press “Power”.
4. Press numerical
keys
O-I-99
for the
desired amount of
minutes.
(Example:
Ol=l
minute;
99=99
minutes) When the
NOTE: The
SC*240
and SC*241 can
be used to control all functions
and devices while in SLEEP/TIMER
mode. To cancel SLEEP/TIMER
mode, repeat steps 1-3. Enter the
number 00 with the numerical
keys to cancel the SLEEP/TIMER
mode.
**
YOU must have Your SC*240 or
SC.241
pointed at Your TV
for
the
SLEEP/TIMER mode to work
properly.
SPECIAL FEATURES
While in one mode, the SC*230,
SC.240,
and SC.241 allow you to
use some features of your
components. The following chart
lists which functions crossover to
other components.
CURRENT OTHER
MODE MODE
VCR TV
TV
VCR
CBL TV
CBL
VCR
CROSSOVER
FUNCTIONS
Volume
Up/Down, Mute
Play, Pause,
Fast Forward
Rewind, Record
Volume
Up/Down, Mute
Play, Pause,
Fast Forward,
Rewind, Record
programmed number of minutes
has elapsed, the SCa240 or
SC.241
will turn off your TV.
20
1. Turn on
COmPOnent
(TV, VCR,
cable box,
or CD player)
2.
Press
“Xtra”.
(the green light will
come on).
STORED CODE IDENTIFICATION
Forget your Codes?
If you didn’t write down the code
numbers when you programmed
your remote and you haven’t
removed the batteries, your Sole
Control can tell you what your
codes are. Just follow these
3.
Press
component key
(“TV”, “VCR”,
“CBL”
or “CD”). The green
light blinks and
stays on).
4.
Press
“~‘.“D”_“D
within eight
seconds (the green
light will stay on).
5. Press “Power”
key until your
component turns
off, waiting two
seconds between
each time you
press “Power”.**
6. As
soon as the
Sole Control turns
your component
off, press
“Xtra”.
**For CD mode, press “Play” until
CD plays.
instructions.
1.
Press the “Xtra”
key (the green
light will come on).
2.
Press the
component key
for which you
would like to
know the code
programmed.
4. Count the number of blinks.
There will be three sets of blinks,
separated by a two second pause.
Make sure you write the code
number below for future use!
TV----_ VCR_
-
_
-
_
CBL_-_-_
CD--_-_
NOTE: IO
blinks=O,
1 blink=1
Example: 3
blinks-pause-
1 blink-pause-lo blinks=310
21
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
