Solem LR-IS-FL Bedienungsanleitung

THE CONNECTED IRRIGATION EXPERT

LR-IS-FL

QUICK

INSTALLATION

GUIDE

PRESENTATION

DOWNLOADING

1. On your smartphone and/or tablet, go to «App Store» ou «Google Play».

2. Search «MySOLEM» in the search bar.

Step 1

3. Download MySOLEM applicaon.

MySOLEM

GET INSTALL

4. Once installed, acvate the Bluetooth®on your smartphone and/ or tablet.

The LR-IS-FL is a Bluetooth®/ LoRaTM mains water mer, remotely controllable

from 2, 4, 6, 9 or 12 staons. Its probe input allows the connecon to a rain

sensor or a ow meter / water meter.

The LR-IS-FL requires the associaon with a LR-MB (relay WiFi/LoRa)

or an LR-BST. (However it can be used in bluetooth)

CREATE UN ACCOUNT

To benet from all LR-IS-FL features, please create a MySOLEM account.

1. Launch MySOLEM app from your smartphone and/or tablet.

2. Go to «My account» by typing on icon.

3. Follow the steps described on the app.

PAIRING

1. Remove the lower hatch to let appear the terminal.

3. Launch the MySOLEM app.

Step 2

2. Connect the 220/24 Vac power supply and replace the hatch.

5. Choose the LR-IS-FL from the list of nearby controllers.

7. To nish the pairing of your LR-IS-FL, follow the next steps described

in the app.

6. (Oponal) Dene a name and a security key for your controller and click

on the buon «Validate».

Note : To idenfy your LR-IS-FL among the nearby controllers, please refer

to the «Default name» present on his product label.

4. Tap on the «Add a module» buton or the «+» buton .

Security key

The security key allows to protect your controller. You can dene it during the

step 6 of the «ASSOCIATION» or access to further informaon by clicking on

the icon at the top right of your screen..

LR-MB PAIRING

Step 3

Note :

- The message «Connecon established» means that the connecon is

reliable.

- The message «No connecon established» means that it is necessary to

bring the LR-IS-FL closer to the LR-MB or vice versa.

To opmize the LoRaTM radio connecon between the LR-MB and the LR-IS-FL

controllers, we advise to install the LR-IS-FL in a plasc valve box under 800

meters to the LR-MB. We also advise to associate all your LR-IS-FL near the

LR-MB before installing them separately in the valve boxes.

2. Click on the top right icon to access to the product’s informaons.

4. Select the LR-MB you want to use.

7. Click on the buon to start the test.

3. Click on «Remote Access».

6. Go back to «Remote access» screen.

1. Select the LR-IS-FL programmer previously installed.

5. Click on the buon «Send» or on the boom of your screen to validate.

Once the pairing nished, you can test the connecon between

your LR-MB and your LR-IS-FL :

Connect the LR-IS-FL to the solenoids as described below.

Use 24V valves only.

LR-BST PAIRING

WIRING

Step 4

24V - S+ C C P 1 2 3 4 5 6 7 8 9 101112C

24V

1. On the applicaon, select your LR-BST, and enter pairing mode .

3. Tap the icon at the top right of your screen to access product’s infor-

maon.

4. Tap on «Accés à distance».

2. Select the LR-IS-FL programmer previously installed.

5. Select in the list the LR-BST inially chosen.

7. Click on the buon to start the test.

6. Return to the LR-IS-FL screen «Remote Access», previously seen.

Once the associaon is complete, you can test the connecon between your

LR-BST and your LR-IS-FL

Step 5

SET SENSOR

The LR-IS-FL has a -S+sensor input on which you can connect a rain sensor

or a pulse sensor / water meter aer cung the blue wire. Once the sensor is

connected, it is necessary to congure it in the applicaon.

2. Click on Add Sensor.

1. Using the MySOLEM mobile app, connect to your LR-IS-FL.

3. Select your sensor type and follow the instrucons given by the applicaon

Step 6

SET FLOWMETER

1. Check the «Instant Value».

Instant Value: Ensures that the volume consumed indicated on the water

meter is the same as the volume displayed on the applicaon. If a gap is

noted, check the wiring (polarity) or adjust the «COEFFICIENT» value.

High threshold (daily volume): maximum consumpon (in liter) that you

do not want to exceed in a period of 24h. If the goal is exceeded you will be

alerted immediately (by e-mail and nocaon smartphone and / or tablet).

Low threshold (daily volume): minimum consumpon (in liters) that you

want to achieve over a period of 24h. If the goal is not reached you will be

alerted the next day at 7am (by e-mail and nocaon smartphone and / or

tablet).

Leak alert volume: water volume threshold (in liter) from which you want to

be alerted.

2. Fill in the remaining elds.

Warning, by default there are no sensor congured.

Staon ow: for each staon, read the owmeter at me T (Cpt1), then at

me T + 5mn (Cpt2).

Make the calculaon (Cpt2 - Cpt1) / 5 => Flow (L / min)

In the applicaon ll in the results.

High Threshold (Staon Flow Alerts): Maximum consumpon warning

threshold in % of the calibrated ow of the channel. The «High threshold»

alert is immediate as soon as it is reached.

Low threshold (Staon Flow Alerts): Minimum consumpon warning

threshold in % of the calibrated ow of the channel. The «High threshold»

alert is immediate as soon as it is reached. For each staon ow alert you have

the possibility to dene the desired type of acon:

• No acon: watering connues.

• Permanent OFF: resuming watering requires a manual ON command (in

the applicaon on the programmer concerned).

• Inhibit the output: stops the staon concerned, requires the

acknowledgment of the alert (in the applicaon on the programmer

concerned) to reacvate the staon.

Stabilizaon me:

Time required before the water ow is stable when starng and stopping the

staon. It eliminates the peak ow (start) or leak (stop). The me is the same

for all staons.

During this period, the consumpon is not taken into account for triggering

alerts or acons.

24V - S+ C C P 1 2 3 4 5 6 7 8 9 101112C

24V

Flowmeter,

water meter

L/mn

Connect your + S - input to a water meter equipped with a ow sensor as

shown above. Use dry contact ow sensors or equivalent.

For polarized ow sensors, when wiring,observe the polarizaon :

Red wire -> + Black wire - > -

INFORMATION ON THE STATUS OF THE LED

Green LED : normal operaon

Blinking green LED : One channel is in progress (the ashing number

corresponds to the staon number acvated).

Green LED and Red Flashing : One channel is in progress and the rain sensor

is acvated or a staon is in progress and the product is in permanent OFF or

several days.

LED Red Fixed : the product is in inializaon mode

LED Red Flashing 2 mes : The programmer has lost me, reconnect to re-

synchronize.

LED Red Flashing 4 mes : One of the staons has a short circuit or is

overconsumpon. The other reason is that you probably have powered down

2 mes in a short me while a staon is sll in progress.

LED Red Flashing 5 mes : You have exceeded the me required to inialize

the mer. Repeat the inializaon procedure.

LED O : The product is not powered.

FAQ

What are the features required for the Bluetooth® product to work?

Android 4.3 (or more) Smartphones or tablets equipped with Bluetooth Smart

4.0 (or more). iOS 9.0 Apple iPhone or iPad running (or more) with Bluetooth

Smart 4.0 (or more)

Why does my staon not start?

It has to be assigned a me and a Program A, B or C to each staon. If several

staons are assigned to the same program, they will start one aer the other.

Why does Program B not start? If Program A departure me is the same than

Program B’s one, then the programs will be executed one aer the other.

What is output P for?

You can connect a master valve or a pump through a relay, on Poutput. It will

start automacally 2 sec before each staon and during each staon watering.

What are the controller’s output S (blue wire) for? You can plug a rain sensor

into Soutputs, to do that you need to cut the blue wire.

How does the rain sensor work? When connected to the yellow wire the rain

sensor acts on the 3 programs. If it is raining, programs A, B and C won’t start;

you must wait the probe to dry before the programs star again. The manual

control “All staons” is not aected by the rain sensor condions.

What is the Water Budget? The Water Budget allows to add a me percentage,

according to the me recorded by each staon. It is generally used during

seasonal changes (for example: summer to autumn, or spring to summer).

E.g.: If you entered Staon 1 = 1h on Program A and Staon 2 = 0h30 on

Program A. Then, if you enter a Water Budget for Program A at 120%, when

starng Program A, staons 1and 2will be increased by 20%, which means

1h12 for Staon 1 and 0h36 for Staon 2.

How can I restart the pairing or the pairing procedure?

To start the pairing procedure again, just bypass the 2 pins of the baery

pressure (baery prior removed) for 30s minimum.

Inhaltsverzeichnis

Andere Solem Timer Handbücher

Solem

Solem BL-NR Bedienungsanleitung

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Tork

Tork TU40 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung