Soleus Air M12-896D Bedienungsanleitung

Soleus Running – GPS Vibe

M12-896D GPS Watch User Manual

(Preliminary – Subject to change without prior notice)

Ref: 12-896 UI 01 / SW 12-896 02V078

Introduction

Thank you for purchasing the GPS Watch. This GPS Watch is packed with personal Training

features like speed, trip time, laps, etc. Watch features include but not limited to the following:

!12/24H Time format

!Chronograph

!World time

!Dual Time T1 and T2

!5 daily Alarms

!RUN mode

!Chronograph mode

!Timer mode

!Data mode

!Set mode

!Vibration Alarm function

"This Watch can communicate with a PC to store and review your

performance.

"This Watch uses a rechargeable battery that can be charged through USB

port of your PC.

Caring for your GPS Watch:

Clean your GPS Watch with a dampened cloth preferably with mild detergent solution. Wipe

dry using a dry cloth. Do not use chemical cleaners and solvents that may damage plastic

components.

Do not store your GPS Watch to prolonged exposure to extreme temperatures as this may

result to permanent damage to your unit.

About GPS:

Global Positioning System (GPS) is a satellite- based navigation system made up of a

network of 24 or more satellites. GPS works best in clear weather condition, anywhere in the

world, 24 hours a day. Tall buildings may interfere with GPS accuracy. When 3 satellite

signals are received, the Watch will have 2D GPS fixed (Latitude and Longitude). When 4 or

more satellite signals are received, the Watch will have 3D GPS Fixed.

Water immersion:

This GPS Watch is designed to be water resistant up to 3 ATM. It can resist water pressure

up to 30 meters. After submersion to water, please make sure to wipe dry and air dry the unit

before using or charging.

Caution:

"Prolonged water submersion may cause electronic shorting in the unit which may

cause minor skin burn or irritation.

Getting Started

Step 1) Know your Watch:

Push button location:

Push button Main function:

S1 – Start / Stop / Increase adjust (+)

S5 – View / OK

S7 – Change Mode / Exit

S11 – Light / Set / Save / Lap / Decrease adjust (-)

Soleus Running – GPS Vibe

Step 2) Charging the Battery:

Charge the unit for at least 4 hours before first use. The length of time for a fully charged

battery will last depending on the actual usage. It is recommended to regularly re-charge your

battery every 1-2 months even if it is not used to maintain good battery condition.

2.1) Plug your USB PC link cable to your PC

2.2) Align the charging clip with the contacts on the back of the Watch.

2.3) Connect the charging clip securely to the watch.

Note: Please thoroughly dry the charging contacts and surrounding area to ensure proper

electrical contact and prevent corrosion.

When the battery is low, it is time to charge the watch.

Battery low condition:

You cannot turn ON the GPS when the battery is low. The watch will display LOW BATT. You

need to recharge the battery in order to use the GPS again.

When the battery is almost low and you still perform your exercise, your data may not be

saved. Please make sure the battery have enough battery power before doing your exercise

in order not to lose your data.

Step 3) Configure your Watch:

Please set your Watch before using it. Follow the following steps in setting the watch:

3.1) Go to SET mode and set the following parameters: AUTO LAP, TIME, UNITS, USER,

NIGHT, Contrast, CHIME, ALARM, TIMER, and VIEW.

•Press S1 or S11 to change the values of the blinking digit.

•Press S5 to enter and set the selected parameter

•The watch will auto exit setting mode if there is no push button operation in 2 to 3

minutes in all setting modes.

How to set the AUTOLAP:

•Auto Lap setting range: 0.4, 1, 2, 3, 4, 5, and OFF

Soleus Running – GPS Vibe

How to set the TIME:

•Year range: 2001 to 2099

•Total of 36 city codes are available for various Time zones.

•Time can be displayed in 12 hour or 24 hour format

•Dual time zone Time 1 and Time 2

How to set the UNITS:

•You can select KM or MI for units.

How to set USER details:

•Age range: 7 to 99 default: 25

•Weight range: 20- 255 KG ( 44-561 LBS) default 65 KG ( 143 LBS)

•Height range: 91-241 cm (3’00” to 7’11”)

How to set the NIGHT mode function:

Night mode settings:

•10 SECONDS – Press S11 will turn ON the Light for 10 seconds.

•20 SECONDS – Press S11 will turn ON the Light for 20 seconds.

•NIGHT ON – Default Start Time / END Time for NIGHT ON setting is 5 PM to 7 AM.

Following are the characteristics of NIGHT ON setting:

oStart Time and END TIME for NIGHT ON setting can be changed in SET

mode/ NIGHT.

oWhen the Night setting is ON, pressing any button within the Start Time / End

Time will turn ON the EL for 10 seconds.

oOutside the Start time / End Time, only press S11 will turn ON the EL for 10

seconds.

oWhen the chronograph is running within the Start Time/ End Time, the EL will

be always ON. It will turn OFF 10 seconds after the chronograph is stopped.

Soleus Running – GPS Vibe

How to set the LCD display CONTRAST:

Contrast range = 10 to 100%

How to set the CHIME:

•When Chime is ON, the Vibration alarm function is also ON.

How to set the ALARM:

•You can set the five alarms independently

•Any alarm can be referred to Time 1 or Time 2

How to set the TIMER:

•You cannot enter Timer setting mode if the TIMER is running or stopped. You need

to reset the TIMER before you can enter the setting mode.

How to set the VIEW

You can select what information to display in Line 1 & Line 2 for RUN mode

3.2) TIME, NIGHT, CONTRAST, & CHIME, can also be set in TIME quick SET mode.

Soleus Running – GPS Vibe

3.3) AUTO LAP, UNITS, USER, and VIEW can also be set in RUN quick SET mode.

3.4) TIMER can also be set in TIMER SET mode

•You cannot enter setting mode if the Timer is running or stopped. You need to reset

the TIMER before you can enter the setting mode.

3.5) ALARM can also be set in ALARM quick SET mode.

Step 4) Acquire Satellite signals:

In order to get the correct time of day and begin using your watch, you have to acquire the

Satellite signals. It may take a few minutes to get the signals.

4.1) Go outside to an open area away from tall buildings and trees. Orient the GPS antenna

towards the sky for best reception. The antenna is located at the 12 o’clock position of

the watch.

4.2) Stand still and do not begin moving while locating the Satellites until the GPS signals are

already received.

4.3) How to Turn ON the GPS: Following are the possible ways to turn on the GPS.

4.3.1) Press S1 in TIME mode.The Watch will display the GPS / INDOOR selection

screen. Select GPS and press S5. The watch will start searching for GPS and go

to RUN mode.

4.3.2) Press S7 to enter RUN, CHRONO, or TIMER mode.

Soleus Running – GPS Vibe

4.3.3) Press and hold S7 for 2 seconds from any mode while GPS is initially OFF.

4.4) How to turn OFF the GPS:

4.4.1) Press and hold S7 for 2 seconds from any mode while GPS is initially ON.

4.4.2) Press S7 to enter RUN, CHRONO, or TIMER mode. Select INDOOR and press

S5 to confirm.

4.4.3) When the chronograph is stopped and reset in any mode, the GPS will go to TIME

mode after 10 minutes and the GPS will be on Standby mode (GPS ring icon

flashing). The GPS will auto turn OFF after 1 hour (GPS ring icon is OFF).

GPS signals and its meaning:

You will hear a beep sound when the Watch has received a GPS signal or when the GPS

signal has been lost. LOST GPS signal will also be displayed in the screen.

Soleus Running – GPS Vibe

Step 5) Go for a RUN:

5.1) Using RUN mode:

5.1.1. How to enter RUN mode:

•If you select GPS and press S5, you will go to GPS GO screen

•If you select INDOOR and press S5, You will go to INDOOR screen.

5.1.2. How to START, TAKE LAP, STOP, and SAVE:

•The watch will take Auto Lap based on the Distance set in Auto Lap setting.

5.1.3. How to change views: Press S5 to change the information displayed in Line 1.

Following are the information displayed as you press S5:

•Information displayed in Line 1 will change as you press S5

•Information displayed in Lines 2 and 3 can be changed in SET mode/ VIEW.

•Note: The watch will remember your previous screen view the next time you come back

to RUN mode.

•

Soleus Running – GPS Vibe

5.1.4. How to view your current data before saving while the chronograph is stopped.

Following are the information as you press S5:

Notes:

oBefore going for a run exercise, it is highly recommended that you set your user

profile first so that the calories will be calculated properly. Go to SET mode/USER.

oWhen the Chronograph is stopped and reset in RUN mode, if no activity for 10

minutes, the GPS will be on Standby mode ( GPS ring icon flashing) and return to

TIME mode.

oWhile in RUN mode, then the GPS signal suddenly becomes weak lost for any

reason, the Watch will display LOST GPS signal until it receives GPS signal again.

oMaximum of 15 hours of track record / 30 data files/ 100 laps for each data file can

be saved in memory.

oSpeed range: 0 to 9999.9 KM/H (MI/H)

oDistance range: 0 to 9,999.99 KM (6209.99 MI)

oChrono range: 0 to 99:59:59

oCalorie range: 0 to 999,999

5.2) Using Chronograph mode:

RUN mode & CHRONO mode has the same chronograph counter. When the chronograph is

started or stopped in RUN mode, the same thing happens in CHRONO mode.

5.2.1. How to enter CHRONO mode:

5.2.2. How to START, take LAP, STOP, and SAVE:

Soleus Running – GPS Vibe

•The watch will take Auto Lap based on the Distance set in Auto Lap setting.

5.2.3. Press S5 to change the information displayed in Line 2. Following are the views

as your press S5:

•Information displayed in Line 2 will change as you press S5.

•Line 1 will display the Chrono or Split Time

•Line 2 will display the Lap time.

•Note: The watch will remember your previous screen view the next time you come back

to CHRONO mode.

5.2.4. How to view your current data before saving while the chronograph is stopped.

Following are the information as you press S5:

5.3) Using TIMER mode:

RUN mode & TIMER mode has the same chronograph counter. When the chronograph is

started or stopped in RUN mode, the same thing happens in TIMER mode.

•The watch has 6 interval timers segment 1 to segment 6.

•The default values for all segments are 00:00:00.

•Please set the TIMERS first before using this mode.

•When you start the Chronograph in other modes like RUN mode, the set Timer

segments will also start counting down unless the timers are set to zero.

•When a segment reaches zero, there will be a 5 seconds beep sound and vibration

alarm. The watch will also display The Loop distance, Segment number, and the Loop

number for 5 seconds and continue counting down the next Timer segment.

•The cycle will loop for 50 loops and auto stop.

•If only 1 segment timer is set and the other segments are set to zero, only that segment

will countdown and loop up to 50 loops.

5.3.1. How to enter TIMER mode.

Soleus Running – GPS Vibe

5.3.2. How to START, STOP, and SAVE.

•The watch will take Auto Lap based on the Distance set in Auto Lap setting.

5.3.3. How to change views in TIMER mode:

•Information displayed in Line 2 will change as you press S5.

•Note: The watch will remember your previous screen view the next time you come back

to TIMER mode.

5.3.4. Ho to view the TIMER segment settings while the chrono is in reset view:

5.3.5. Press S5 while the chronograph is stopped to view your current data before

saving. Following are the information as you press S5:

Inhaltsverzeichnis

Andere Soleus Air Betrachten Handbücher

Soleus Air

Soleus Air M15-019D Bedienungsanleitung

Soleus Air

Soleus Air GPS 1.0 Bedienungsanleitung

Soleus Air

Soleus Air Sprint SR022 Bedienungsanleitung

Soleus Air

Soleus Air SF001 Bedienungsanleitung

Soleus Air

Soleus Air SG005 Bedienungsanleitung

Soleus Air

Soleus Air SG008 Bedienungsanleitung

Soleus Air

Soleus Air SG102 Bedienungsanleitung

Soleus Air

Soleus Air SPORTS STRAP Bedienungsanleitung

Soleus Air

Soleus Air SG006 Bedienungsanleitung

Soleus Air

Soleus Air GPS mini Watch Bedienungsanleitung

Soleus Air

Soleus Air SG007 Bedienungsanleitung

Soleus Air

Soleus Air SH010 Bedienungsanleitung

Soleus Air

Soleus Air SG010 Bedienungsanleitung

Soleus Air

Soleus Air GPS 2.0 Watch Bedienungsanleitung

Soleus Air

Soleus Air SG009 Bedienungsanleitung

Soleus Air

Soleus Air GPS Fit 1.0 Bedienungsanleitung

Soleus Air

Soleus Air SG004 Bedienungsanleitung

Soleus Air

Soleus Air SR017 Bedienungsanleitung

Soleus Air

Soleus Air SG002 Bedienungsanleitung

Soleus Air

Soleus Air SH011 Bedienungsanleitung

Soleus Air

Soleus Air PR HRM SH009 Bedienungsanleitung

Soleus Air

Soleus Air SR021 Bedienungsanleitung

Soleus Air

Soleus Air SH011 Bedienungsanleitung

Soleus Air

Soleus Air SG013 Bedienungsanleitung

Beliebte Betrachten Handbücher anderer Marken

Pandora

Pandora WATCH2 Bedienungsanleitung

Casio

Casio QW-4343 Bedienungsanleitung

Suunto

Suunto X6 Bedienungsanleitung

Seiko

Seiko N830 Bedienungsanleitung

MotionX

MotionX 365 Bedienungsanleitung

Garmin

Garmin VENU SQ 2 Bedienungsanleitung

QCY

QCY Watch GTC Bedienungsanleitung

Canyon

Canyon Cindy CNE-KW41WP Bedienungsanleitung

Esq

Esq Watches Installationsanleitung

Crane

Crane AA5-CDSM-3A Bedienungsanleitung

Timex

Timex W-214 Bedienungsanleitung

DETOMASO

DETOMASO MATERA Bedienungsanleitung

Geemarc

Geemarc Watch N Shake Bedienungsanleitung

LORUS

LORUS W590 Bedienungsanleitung

STENLILLE

STENLILLE Actío Bedienungsanleitung

Casio

Casio 5594 Bedienungsanleitung

Sinn

Sinn HUNTER'S WATCH 3. Edition Bedienungsanleitung

Slazenger

Slazenger SLZ800 Bedienungsanleitung