Solid State Cooling Systems TCS-110 Bedienungsanleitung

Preliminary

Product Manual

TCS-110

Precise, uniform surface temperature with integrated controller

Microtiter Temperature Control Stage

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1 
SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 1 
TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6 
 
 
Table of Contents 
 
SAFETY PRECAUTIONS AND SYMBOLS ____________________________________________2 
SECTION 1 ________________________________________________________________________3 
INTRODUCTION ____________________________________________________________________3 
SECTION 2 ________________________________________________________________________4 
PRELIMINARY SPECIFICATIONS ________________________________________________________4 
SECTION 3 ________________________________________________________________________6 
HOOK UP_________________________________________________________________________6 
3.1 Mechanical Installation _______________________________________________________ 7 
3.2 Electrical Installation/Connections (see figure 3A) __________________________________ 8 
SECTION 4 ________________________________________________________________________9 
START UP_________________________________________________________________________9 
4.1 Start-up when connected directly to a PC:_________________________________________ 9 
4.2 Start-UP when connected to a PC through a Router or a Server________________________ 9 
SECTION 5 _______________________________________________________________________16 
OPERATION ______________________________________________ _______________________18 
SECTION 6 _______________________________________________________________________20 
SYSTEM ALARMS/TROUBLESHOOTING _________________________________________________20 
SECTION 7 _______________________________________________________________________20 
CLEANING YOUR CHILLER ___________________________________________________________20 
SECTION 8 _______________________________________________________________________20 
TECHNICAL SUPPORT_______________________________________________________________20 
WARRANTY POLICY _____________________________________________________________21 
 
 
 
 
 
 

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 2

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

SAFETY PRECAUTIONS AND SYMBOLS__________________

Caution! Burn and Freeze Hazard!

The TCS-110 microtiter temperature control surface

temperatures can range from 0°C to 110°C. Do not

touch the top surface while in operation!

Symbols Used in this Manual

The red CAUTION equilateral triangle symbol appears throughout

the manual. Please follow the important instructions

accompanying this symbol to avoid significant damage to the

chiller.

The red WARNING equilateral triangle symbol appears

throughout the manual accompanying certain maintenance and

repair activities. Please follow the important instructions

accompanying this symbol to avoid situations that could cause

injury to the operator or other personnel.

The red DANGER equilateral triangle symbol appears throughout

the manual accompanying certain maintenance and repair

activities. Please follow the important instructions accompanying

this symbol to avoid injury to the operator. Only trained

personnel should undertake any activity marked by the red

DANGER triangle.

CAUTIONS

▪Safe operation the TCS-110 requires earth ground be connected to Pin. Do Not Operate the

TCS-110 without proper grounding!

▪Operation of the TCS-110 in any manner not recommended in this manual could compromise the

safety of operating personnel.

▪Never disassemble the TCS-110 unit as irreparable damage may occur.

CAUTION

DANGER

WARNING

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 3

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

TCS-110 MICROTITER TEMPERATURE CONTROL STAGE

SECTION 1

INTRODUCTION_________________________________________________

The TCS-110 provides a temperature controller platform for all

ANSI SBS 2004-1 microwell plates. It features a built-in controller

and DC power management to provide uniform surface

temperature with high heat transfer rates to repeatably control the

temperature of microwell plates from 0°C to 110°C. No separate

controller is necessary. The TCS-110 features a TCPIP Ethernet

interface allowing multiple units to be connected to the host tool.

It may be mounted either on top of a deck or integrated into a deck

surface via an interface fixture. SSCS can customize interface

fixture to meet your specific needs.

The complete system includes an external, universal 24VDC DC

power supply and power cord.

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 4

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

SECTION 2

PRELIMINARY SPECIFICATIONS ___________________________________

Operating Range: 0°C to 110°C

Ambient Temperature Range: 10°C to 40°C non-condensing

Stability / Repeatability: ±0.1°C with constant load (even near ambient)

Temperature Uniformity: ±0.5°C @ 37°C in 22°C ambient

Temperature Ramp Rates2: Average heating ramp rate from 4°C to 99°C = 0.3°C per second

Average cooling ramp rate from 4°C to 99°C = 0.2°C per second

Communications: Ethernet 3

Alarms: Fan fail, RTD fail, Temperature out of range

Dimensions:

Top Plate: 3.590” x 5.245” (ANSI/SBS 1-2004 microplate standard)

Overall Above deck (W x L x H): 6.45" x 4.29" x 1.38" (16.3 x 10.9 x 3.5 cm) - with collar

Overall Below deck (W x L x H): 5.66" x 3.27" x 4.35" (14.4 x 8.3 x 11.0 cm)

Weight: 4 lbs (1.8 kg) without external power supply

DC Operating Voltage: 24 VDC, 8 amps DC max

External Power Supply Input: Universal: 100-240 VAC, 50/60 Hz, 4 amps max

Standards: RoHS 3, ANSI/SBS 1-2004,

UL, CAN/CSA and EN 61010-1, CE 61010-1 (Pending)

Warranty: 2 years

Notes:

1. All specs are preliminary and are subject to change after Beta testing is completed.

2. Ramp rates shown are typical, measured without inserts.

3. Each stage has a unique TCPIP address. There is no limit to the number of stages.

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 5

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

Figure 1A: Typical Cooling and Heating Rates

Figure 1B: Typical Heating Rate

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 6

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

SECTION 3

HOOK UP______________________________________________________

Figure 2: Front View

Figure 2: Rear View

Input DC Power Connector

Ethernet Connector

Air Inlet

Air Outlet

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 7

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

3.1 MECHANICAL INSTALLATION

Mounting:

The TCS-110 is designed for mounting to a deck via an interface

bracket as shown in figure 3 below. Alternatively. The TCS-110 feet

have four (4) mounting holes at the bottom for mounting from below

using M3 screws.

Figure 3: Mechanical Layout without Collar

Figure 4: Robot Alignment Witness Mark

Robot Witness Mark

The TCS-110 comes with a witness mark for robot

alignment, see figure 4.

Air Considerations:

Good airflow is essential to the operation of the TCS-

110. The air intake is from the bottom and exits out

the left and right sides (see Figure 2). Do not block

airflow into or out of the TCS-110. SSCS

recommends maintaining 2” of clearance around the

air inlets (front and back sides at the bottom) and out

the left are right sides

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 8

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

3.2 ELECTRICAL INSTALLATION/CONNECTIONS (SEE FIGURE 3A)

The TCS-110 comes with a 220w universal, external DC power

supply (brick) with the DC power connector that plugs into the TCS-

110, it ships with a regional AC power cord

A wide variety of power cords are available to support universal

power operation:

Table 1: Power Cord Part Numbers

Country / Region

Part Number

USA/Canada

22-22333-1

Europe

22-22333-2

Japan

22-22333-3

22-22333-4

Israel

22-22800-1

Australia

22-23213-1

Korean

22-23526-1

China (3 prong)

22-23661-1

Brazil

22-25122-1

India/South Africa 6A (Type D)

22-26025-1

India/South Africa 15A (Type M)

22-26025-2

NEMA 6-15 208 US Straight

16-23918-1

NEMA L6-15 208 US Twist

16-23918-2

Power: The TCS-110 has a Molex Mini-Fit BMI 4204 series

connector for DC power and ground, 24VDC power may be

connected directly into the TCS-110 via this connector:

Molex PN: 0015246040

Mating Molex Connector: Mini-Fit Jr. series 5557

PN: 0039013042

Pin-out:

Pin 1- Chassis Ground

Pin 2- +24V DC

Pin 3- DC(-) (return)

Pin 4- Not Used

Fuses:

Controller: 0.5amp (5mm x 20mm) GDB quick acting glass, meets

IEC 127-2

Replacement Fuse: SSCS#, Allied Electronics

Remote Communication: The TCS-110 is controlled though the

Ethernet port on the Front panel. This port is a standard RJ-45 jack.

For more information, refer to section 7.1.

Electrical Shock

Hazard: Never Plug

in a Line Cord with

Wet Hands

WARNING

TCS-110 TEMPERATURE CONTROL STAGE PRODUCT MANUAL 52-13129-1

SOLID STATE COOLING SYSTEMS,167 MYERS CORNERS ROAD,WAPPINGERS FALLS,NY 12590 9

TELEPHONE:(845) 296-1300 FAX:(845) 296-1303 WEB:WWW.SSCOOLING.COM VERSION E6

SECTION 4

START UP _____________________________________________________

The TCS-110 is operated via TCPIP Ethernet; its default settings are

as follows:

IP Address: 192.168.1.88

Subnet Mask 255.255.255.0

Gateway: 192.168.1.1

IP Configuration Static

Password admin

Port Number 10001

4.1 START-UP WHEN CONNECTED DIRECTLY TO A PC:

1) Plug the 24VDC power supply into your AC wall outlet or connect

24VDC to the TCS-110 as per section 3.2

2) Connect your CAT-5 Ethernet Cross-Over Cable to the TCS-110 RJ-

45 ethernet jack. Set your computer to a static IP address in this

range: 192.168.1.2-254 excluding 88.

3) Set your Subnet Mask to 255.255.255.0 and Gateway to 192.168.1.1.

4) The TCS-110 is now ready for operation. See section 4.3.

4.2 START-UP WHEN CONNECTED TO A PC THROUGH A ROUTER OR A SERVER

1. Plug the 24VDC power brick into your AC wall outlet or connect 24VDC to the TCS-110 as per

section 3.2.

2. Connect a standard CAT-5 Ethernet cable from the computer to the router, and another standard

CAT-5 Ethernet cable from the router to the TCS-110 RJ-45 Ethernet jack.

3. On the final test sheet provided upon shipment of the TCS-110 unit, find the IP address that has

been assigned to the unit. This address can be used in Section 4.3 to connect with the graphical

user interface.

4.3CONNECTING WITH SSCS GRAPHICAL USER INTERFACE

Solid State Cooling has developed a graphical user interface, or GUI, to be used to communicate with

the TCS-110 easily. For more information on the GUI and how to acquire it, contact the Sales

department at Solid State Cooling. If you do not wish to use this GUI, proceed to Section 5. (Note:

Establishing an Ethernet connection requires the use of the GUI.)

The following is an explanation of how to use the GUI to connect to the TCS-110 only after executing

either Section 4.1 or Section 4.2.

CAUTION

Do Not Change the

UART Settings. The

TCS-110 will not

operate if you do.

Inhaltsverzeichnis

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema