Solid State Logic C200 routing guide Bedienungsanleitung

Installation Guide

C200 Insta ation Guide

Solid State Logic

Digital Broadcast Console

Installation Guide

Version 2.0.0

82S6PC2010C

C200 Insta ation Guide

Solid State Logic

S O U N D || V I S I O N

Begbroke, Oxford, England, OX5 1 U • +44 (0)1865 842300

320 West 46th Street, 2nd Floor, New York, NY 10036, USA • +1 (1) 212 315 1111

Suite 401, 5757 Wilshire Blvd, Los Angeles, CA 90036, USA • +1 (1) 323 549 9090

3-55-14 Sendagaya, Shibuya-Ku,Tokyo 151-0051, Japan • +81 (0)3 5474 1144

7 bis, rue de la Victoire, le Blanc Mesnil, Paris 93150, France • +33 (0)1 48 67 84 85

Via Timavo 34, 20124 Milano, Italy • +39 (0)39 2328 094

Visit SSL at U L: http://www.solid-state-logic.com

All ights reserved under International and Pan-American Copyright Conventions

C100, C200, C300, Centuri, C-SB StageBox, NetBridge, NiTech,

Solid State Logic and SSL are trademarks of Solid State Logic

All other product names and trademarks are the property of their respective owners

No part of this publication may be reproduced in any form or

by any means, whether mechanical or electronic, without the

written permission of Solid State Logic, Oxford, England

As research and development is a continual process, Solid State Logic reserves the right

to change the features and specifications described herein without notice or obligation

E&OE

Contents

1 Introduction 2

2 Safety Considerations 3

Safety Warnings 4

CE/ CC/WEEE Certification and Directives 5

3 Pre-Installation Information 6

Services Provided by SSL 6

Physical/Structural 7

Console ootprint and Side Profile 8

Centuri and Stagebox Side View 10

Technical 11

4 System Components 13

Console rame 13

The Centuri Processor 15

The Centuri Processor Cards 16

C-SB Stagebox (option) 21

MORSE (option) 21

NetBridge (option) 23

Script Tray (option) 25

Loudspeaker Shelf (option) 25

XGA Video Switcher 25

5 Installation 27

Connections 27

Earth Connection 27

Console Control 29

PSU Status 31

Sync 31

I/O – MicAmp Card 33

I/O – Analogue Card 33

I/O – Digital Card 35

I/O – MADI Card 35

GPI/O Card 37

C-SB Stagebox Wiring 39

Talkback and Oscillator 43

Phasescope and Meter Wiring 45

Appendices

A Equipment Specifications 47

B Connector Details 51

C Connector Pinouts: Console 53

Processor Crate 56

NetBridge 62

D Audio Interfacing 63

E Environmental Specification 65

Stagebox Installation Requirements 67

G SSL Part Numbers by Description 69

Page 1

Section 1 – Introduction

The object of this manual is to provide purchasers of the C200™ Console and Centuri™ Processor with information in

the following areas:

• Safety considerations

• Installation requirements

• Items supplied: – Main components and optional items

• Installation: – Physical assembly

– Electrical connections and cabling

– System options

• Specifications and Physical dimensions

• Pinouts of standard connectors

The information provided by this manual is relevant to all of the versions of the C200.

The aspects of the C200 which can be customised – frame size, channel layout, meter panel as examples – will be fully

documented in the Custom Specification information for a specific console.

The Custom Specification information, which details the actual console as built, will be found in Section 10 of the console’s

Service Manual.

Page 2

C200 Insta ation Guide

Section2 – Safety Considerations

This section contains definitions and warnings, and practical information to ensure a safe working environment. Please take

time to read this section before undertaking any installation work.

Definitions

‘Maintenance’

All maintenance must be carried out by fully trained personnel.

Note: it is advisable to observe suitable ESD precautions when maintaining electronic assemblies.

‘Non-User Adjustments’

Adjustments or alterations to the equipment may affect the performance such that safety and/or international

compliance standards may no longer be met.Any such adjustments must therefore only be carried out by fully trained

personnel.

‘Users’

This equipment is designed for use solely by engineers and competent operators skilled in the use of professional

audio equipment.

‘Environment’

This product is a class A product intended to form an integrated component part of a professional audio recording,

mixing, TV, radio broadcast or similar studio wherein it will perform to specification providing that it is installed

according to professional practice.

Installation Instructions

Voltage Selection and Fusing

Although the majority of SSL equipment uses auto-ranging power supplies, some sub-systems have user-selectable voltage

inlets. Always confirm that the input mains voltage range is set correctly before applying power. Always isolate the mains

supply before changing the input range setting.

If it is ever necessary to replace a blown mains-fuse, then always use the correct rating and type of replacement. If a

correctly rated fuse continues to blow, then a fault exists and the cause should be investigated or the unit returned to SSL

for repair/replacement as appropriate.

Details of mains settings and correct fuse ratings can be found in Appendix A of this manual.

Electrical Safety Warning

When installing or servicing any item of SSL equipment with power applied, when cover panels are

removed, HAZARDOUS CONDITIONS CAN EXIST.

These hazards include: High voltages

High energy stored in capacitors

High currents available from DC power busses

Hot component surfaces.

Any metal jewellery (watches, bracelets, neck-chains and rings) that could inadvertently come into contact

with uninsulated parts should always be removed before reaching inside powered equipment.

Safety Considerations

Section 2

Page 3

Safety Earth Connection

Any mains powered item of SSL equipment that is supplied with a 3-core mains lead (whether connectorised or not) should

always have the earth wire connected to the mains supply ground.This is the safety earth and grounds the exposed metal

parts of the racks and cases and should not be removed for any reason.

Mains Supply and Phases

SSL equipment is designed for connection to single-phase supplies with the Neutral conductor at earth potential – category

TN – and is fitted with a protective fuse in the Live conductor only. It is not designed for use with Phase (Live) and Neutral

connections reversed or where the Neutral conductor is not at earth potential (TT or IT supplies).

All mains powered assemblies must be connected to the same mains phase. In particular, note that as PSU redundancy is

standard, the two input leads must NOT be connected across different phases.

Mains cables will be coded with either of the following colour schemes:

1or 2

LIVE: Brown Black

NEUTRAL: Blue White

EARTH: Yellow/Green Green

Mains Isolation and Over-Current Protection

An external disconnect device (switch) is required for this equipment which must be installed according to current wiring

regulations. A detachable power cord, if fitted to this equipment, is a suitable disconnect device; otherwise an approved

disconnect switch is required – the rating of which is defined in the product specification (Appendix A) and on the

equipment itself.

An external over-current protection device is required to protect the wiring to this equipment which must be installed

according to the current wiring regulations.The fusing or breaking-current is defined in the product specification. In certain

countries this function is supplied by use of a fused plug.

Some equipment (specifically units with PSU Redundancy) utilises multiple power sources. This is clearly marked on the

equipment.The finished installation must also be clearly marked to ensure that all sources of power are removed before

servicing begins.

Physical Safety

Most subsystems are too heavy for one person to lift.Take particular care when removing the computer chassis from the

equipment rack.

If the console trim is removed for any reason then there may be sharp edges exposed on the frame metalwork.

Page 4

C200 Insta ation Guide

CE Certification

The C200/Centuri system is CE compliant. Note that the majority of cables supplied with SSL equipment are

fitted with ferrite rings at each end.This is to comply with the current regulations and these ferrites should not

be removed.

If any of the console metalwork is modified in any way – particularly the addition of holes for custom switches etc. – this

may the adversely affect the CE certification status of the product.

FCC Certification

The equipment which forms a C200/Centuri system has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the CC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the interference

at his own expense.

Instructions for Disposal of WEEE by Users in the European Union

The symbol shown here, which is on the product or on its packaging, indicates that this product must not

be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment

by handing it over to a designated collection point for recycling of waste electrical and electronic

equipment.The separate collection and recycling of your waste equipment at the time of disposal will help

to conserve natural resources and ensure that it is recycled in a manner that protects human health and

the environment. or more information about where you can drop off your waste equipment for recycling,

please contact your local city office, your household waste disposal service or where you purchased the

product.

AAA

Safety Considerations

Section 2

Page 5

Section 3 – Pre Installation Information

Physical installation of the console is normally carried out by a specialised transportation company. In some cases this will

have been arranged by the local SSL office, in other cases by the facility.

The cables that run between console and processor can be shipped in advance of the console in a separate kit (the pre-

install kit). These cables should be installed by the facility engineers. Instructions for installing these cables are found on

pages 29 to 31 of this manual.

Note: Cables for the connection of ancillary functions, eters, talkback, oscillator and any custom switches etc. are not

supplied by SSL and will need to be provided by the facility. See pages 43–45 for wiring information.

Before the console is installed all building work should be completed and the environment MUST be clean otherwise the

warranty will be rendered invalid.

Before commissioning can take place the following must be completed:

• Air Conditioning installed, tested, blown-through and working

• Lighting installed and tested

• Cable Trunking installed

• Wall and floor finishes completed

• Power Distribution installed and tested

• Cables installed and tested

• Monitor loudspeakers installed and working

• Other utilities (telephone, water etc.) available

Services provided by SS

Commissioning

All C200 systems include on-site commissioning by an SSL engineer. This is usually expected to take from 2 to 4 days

depending on system size, configuration and options. Large systems, or consoles split for shipment, may require an

additional 1–2 days of commissioning time.

You will be contacted by your local SSL office or agent shortly before delivery to arrange a commissioning date.

Training

Three days of standard operator training are provided with each C200 system. If required, this is scheduled to take place

immediately following the commissioning period and is usually carried out by the commissioning engineer.A further day of

advanced operator training is available at additional cost.

On-site maintenance training is also available at additional cost.This can be either one day for a basic overview or two days

for more advanced training.

Training should be requested at time of order. or all training, we recommend that no more than five persons attend each

session. If the use of an interpreter is necessary the training period may need to be extended (at additional cost). Note

that travel and subsistence costs are not normally included. Please contact SSL’s training department at: support@solid-

state-logic.com.

Warranty

All systems normally include 13 months warranty from date of shipment.This does not include consumable items such as

magnetic media, disks etc. urther details may be found in SSL’s Conditions of Trading (printed on the reverse of all SSL

invoices).

Page 6

C200 Insta ation Guide

Andere Handbücher für C200 routing guide

Andere Solid State Logic DJ-Equipment Handbücher

Solid State Logic

Solid State Logic Nucleus Bedienungsanleitung

Solid State Logic

Solid State Logic AWS V4 Logictivity Bedienungsanleitung

Solid State Logic

Solid State Logic XL-Desk Bedienungsanleitung

Solid State Logic

Solid State Logic C200 routing guide Bedienungsanleitung

Solid State Logic

Solid State Logic Duality Bedienungsanleitung

Solid State Logic

Solid State Logic Super-Analogue Outboard XR622 Bedienungsanleitung

Solid State Logic

Solid State Logic SSL UF1 Bedienungsanleitung

Solid State Logic

Solid State Logic XLogic Alpha Channel Bedienungsanleitung

Solid State Logic

Solid State Logic C200 routing guide Bedienungsanleitung

Solid State Logic

Solid State Logic LIVE Bedienungsanleitung

Solid State Logic

Solid State Logic AWS 900+ Bedienungsanleitung

Solid State Logic

Solid State Logic C100 HDS Technisches Handbuch

Solid State Logic

Solid State Logic Nucleus Bedienungsanleitung

Solid State Logic

Solid State Logic SSL UF8 Bedienungsanleitung

Solid State Logic

Solid State Logic AWS 900+ SE Bedienungsanleitung

Solid State Logic

Solid State Logic C100 HDS Technisches Handbuch

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung