Solinst 101 P2 Bedienungsanleitung
Connecting Polyethylene Replacement Tape to Reel
High Quality Groundwater and Surface Water Monitoring Instrumentation
(Page 1 of 2)
Model 101 P2
Tools and Materials Needed
1. Model 101 P2 Replacement Tape Assembly
• Comes with P2 Probe attached
• Grommet
• Jumper Cable (New Tape - 3 Pin to 2 Pin) (#110508)
• 3 Pin Molex Connector Housing
2. Phillips or Robertson Screwdriver
3. Wire Cutters
Instructions
1. Place reel on a flat workbench with faceplate up. Undo the
three screws from the faceplate, and slowly remove it from
the reel.
2. For the Mk1 Model 101 P2, disconnect the Tape Molex
Connector from the Faceplate Molex Connector.
3. For the Mk2 Model 101 P2 Water Level Meters, press down
on the white terminals of the push-release fittings on the
circuit board to remove the tape leads.
Note: The replacement tape comes with a new grommet.
The old grommet may be replaced with the new one,
or left in if not damaged.
Wires Connected
to Faceplate
Faceplate Molex
Connector
Inside View of Mk1 101 P2 Reel Hub
Showing Tape Connection Detail
Grommet
Black Plastic Bridge
Tape Molex
Connector
Inside View of Mk2 101 P2 Reel Hub
Showing Tape Connection Detail
Grommet
Black Plastic Bridge
Tape Leads
4. Undo the two screws from the black plastic bridge holding
the tape inside the reel hub, and remove the top piece of the
bridge.
5. For the Mk1 Model 101 P2, use the wire cutters to cut the
old Tape Molex Connector from the old tape. Pull the old
tape through the grommet and remove it from the reel.
6. For the Mk2 Model 101 P2 Water Level Meters, simply pull
the old tape through the grommet and remove it from the
reel.
7. Feed the new tape through the grommet into the reel hub.
Note: The Jumper Cable is required if you are connecting the new
tape to a Mk1 Model 101 Water Level Meter that has a
Molex connector from the faceplate electronics with a 2 pin
connection.
3 Pin Molex
Connector
Housing
Jumper Cable
More Info | Instructions | Get Quote
Solinst Canada Ltd. 35 Todd Road, Georgetown, Ontario Canada L7G 4R8 www.solinst.com
E-mail: instruments@solinst.com Tel: +1 (905) 873-2255; (800) 661-2023 Fax: +1 (905) 873-1992
January 27, 2022
(#108708) (Page 2 of 2)
9. For the Mk2 Model 101 P2 Water Level Meters, cut the
pins on the tape leads at the point show in the photo below.
Use pliers to flatten the pins against the tape leads, so they
fit into the terminals on the circuit board (see Step 12).
Mk2 101 P2 Tape Connection
Negative pin inserted into terminal with
white square below it on the circuit board.
10.Position the tape inside the reel hub with black plastic bridge
over top and refasten the two screws to secure the tape to
the reel.
11.For the Mk1 Model 101 P2, use the Jumper Cable to
connect from the new 3 Pin Tape Molex Connector to the
2 Pin Faceplate Molex Connector.
102
1
2
9 8ft 7
13.With the probe in a glass of tap water, turn the Meter
‘ON’. If the buzzer or light do not activate, check the tape
connections.
14.Replace the faceplate on the reel and re-secure the three
screws.
15.Slowly wind the tape onto the reel, holding to ensure no
slack.
Jumper Cable (New Tape - 3 Pin to 2 Pin) (#110508)
Connect to Tape
Molex Connector
Connect to
Faceplate Molex
Connector
12.For the Mk2 Model 101 P2 Water Level Meters, press down
on the white terminals on the circuit board and insert the
tape leads. Release the terminals and the leads should be
secured. The negative pin on the top tape lead (numbers
facing up) is inserted into the terminal with a white square
below it on the circuit board. See following images.
White Square
102
1
2
Negative
Connector Pin
8. For the Mk1 Model 101 P2, by hand, insert the connector
pins into the new Tape Molex Connector housing. The
negative connector pin is inserted into the terminal on the
pointed side of the Tape Molex Connector housing and the
positive pin into the middle terminal (the third terminal is left
open). The negative pin is above the numbers on the tape
(see diagram below).
3 Pin Molex
Connector
Housing
Andere Solinst Kabel und Steckverbinder Handbücher
