Sollae Systems PES-2405 Bedienungsanleitung

PES-2405 User Manual > Introduction

2019-03-04 Sollae Systems page 1 of 28

Introduction

PES-2405

PES-2405, stepper motor controller Ⅱ, is a smart expansion board for PHPoC boards. With this

board, you can accurately control various stepper motors.

Highlights of PES-2405

bi-polar stepper motor controller

driving modes: micro step(maximum division rate: 1/32)

motor voltage: DC 4 ~ 18[V]

maximum current on each coil: 1[A]

current comsumption: approximately 30[mA]

※ Caution: PES-2405 requires a PHPoC board which has a firmware 1.3.0 or higher version.

What is the Smart Expansion Board?

A smart expansion board has own devices and firmware unlike the other

expansion boards. This board communicate in a master-slave protocol through

the designated port. Two or more smart expansion boards can be connected to

one PHPoC board and each of them required to be setting a slave id.

PES-2405 User Manual > Dimension

2019-03-04 Sollae Systems page 2 of 28

Dimension

Body

PES-2405 User Manual > Dimension

2019-03-04 Sollae Systems page 3 of 28

with Terminal Block (T type)

with Terminal Block (S type)

※ Dimensions(unit : mm) may vary according to a method of measurement.

PES-2405 User Manual > Schematic

2019-03-04 Sollae Systems page 4 of 28

Schematic

This is the schematic of PES-2405.

PES-2405-R2-PO.pdf

PES-2405 User Manual > Layout

2019-03-04 Sollae Systems page 5 of 28

Layout

PES-2405 User Manual > Layout

2019-03-04 Sollae Systems page 6 of 28

1. Stepper motor & Power port

Stepper motor & Power port is a terminal block. It has six terminals and a 5mm pitch.

label description

M1+, M1-, M2+, M2- connect to stepper motor

VM, GND connect to power

Connecting to a bipolar stepper motor

PES-2405 is a controller for bipolar stepper motors. An example of connection with a bipolar stepper

motor is as follows:

PES-2405 User Manual > Layout

2019-03-04 Sollae Systems page 7 of 28

Connecting to a unipolar stepper motor

If you want to connect a unipolar stepper motor to PES-2405 refer to two examples below.

Supplying power

GND and VM are input port of supplying power(DC 4 ~ 18V) to run motors. Supplying power

through this port is positively necessary. Check the DC polarity when you input the power.

PES-2405 User Manual > Layout

2019-03-04 Sollae Systems page 8 of 28

2. Digital input port

This port is used to connect limit switches and cannot be used for other purposes.

An example of connection with limit switches is as follows:

G means ground and all ground pins are connected each other

0, 1, 2 and 3 are the index number of input ports and all of them are pulled up

3. SLAVE ID Switch

A slave ID is used when PHPoC board identifies each smart expansion board. So, each smart

expansion board, which is connected to a PHPoC board, should have a unique slave ID. The slave ID

can be set one of the numbers from 1 to 14 by 4 DIP switches as follows:

PES-2405 User Manual > Layout

2019-03-04 Sollae Systems page 9 of 28

4. LED

PES-2405 has 2 status LEDs. The one, on the top of the board, is connected to 3.3V and the other

one, on the bottom of the board is connected to 5V. The operations of both LEDs are the same and

they are as follows:

about ID setting

state operation

normal repeat On/Off in every second

abnormal blinks very quickly

about running motor

state operation

ready repeat On/Off in every second

running shortly turned on 4 times in every second

locked shortly turned off 4 times in every second

out of control off

PES-2405 User Manual > How to use

2019-03-04 Sollae Systems page 10 of 28

How to Use

The steps for using PES-2405 are as follows.

1. Connect to a PHPoC board

PES-2405 cannot be used alone. Be sure to connect to PHPoC board.

2. Install Software (IDE)

PHPoC Debugger is a software which is used for configuring PHPoC products and developing

PHPoC script. It is required to install this software on your PC because PES-2405 must be controlled

by PHPoC.

PHPoC Debugger Download Page

PHPoC Debugger Manual Page

3. Use SPC Library and Sample Codes

The SPC library is for smart expansion boards such as PES-2405. This library makes it easy for you to

use smart expansion boards. Refer to the manual page of SPC library for more information.

SPC Library Manual Page

Inhaltsverzeichnis

Andere Sollae Systems Controller Handbücher

Sollae Systems

Sollae Systems PES-2403 Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H14A Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H12G Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H10 Technisches Handbuch

Sollae Systems

Sollae Systems CIE-H10G Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H12 Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H10A Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-M10 Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-M10A Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H10 Bedienungsanleitung

Sollae Systems

Sollae Systems CIE-H14G Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch