Sonel P-2 Bedienungsanleitung

OPERATION

MANUAL

VOLTAGE TESTER

P-2

SONEL S. A.

ul. Wokulskiego 11

58-100 Świdnica

Version 1.8 May 15, 2012

Principal characteristics of the device:

•Measurement of direct and alternative voltage

presented on a display within the range be-

tween 1.5 and 750V with the maximum exacti-

tude of 0.1V,

•Indication of direct and alternative voltage on

the diode indicator: 12, 24, 50, 120, 230, 400,

690V,

•Indication of polarization of the direct voltage

(on the diode indicator and the display),

•The diode indicator does not require a battery,

•The one-pole voltage indicator for voltages ex-

ceeding 50V,

•Measurement of resistance within the range

between 0 and 1999Ω,

•Test of continuity of the circuit with optical and

acoustic signalling,

•Function of checking the order of phases in

three-phase circuits,

•Function of test of differential current switches,

•HOLD function – holding of any measurement

o the display,

•Legible back-lit display,

•Illumination of the display connection point,

•Ergonomic and hermetic casing with elastomer

(IP65),

•Automatically switching off display in the case

of inactivity.

TABLE OF CONTENTS

SAFETY ..............................................4

MEASUREMENTS............................5

2.1

ONTROL OF OPERATION OF THE

TESTER

............................................5

2.2

VOLTAGE TEST

...............5

2.3

RCD

OPERATION TEST

.....................6

2.4

POLE PHASE TESTING

...............6

2.5

IRCUIT CONTINUITY TEST

..............7

2.6

EASUREMENT OF RESISTANCE

......7

2.7

HOLD

FUNCTION

.....................7

2.8

HASE ORDER TEST

.........................8

2.9

LLUMINATION OF THE MEASURED

POINT

..............................................8

REPLACEMENT OF THE

BATTERIES.......................................9

CLEANING AND MAINTENANCE9

STORAGE...........................................9

DISMANTLING AND

UTILIZATION.................................10

TECHNICAL DATA........................10

MANUFACTURER..........................12

Thank you for having purchased our voltage tester.

The P-2 tester is a modern, high-quality measure-

ment instrument, which is easy and safe to use.

However, reading the present manual will permit

you to avoid measurement errors and prevent

possible problems regarding operation of the de-

vice.

Note:

The producer reserves the right to realise

modifications as regards the appearance of

the device, its equipment and technical data.

1 Safety

The purpose of the P-2 device is to test volt-

age and the continuity of connections as well as

measurements of resistance. In order to guarantee

the correct operation of the device and correctness

of the obtained results observe the following rec-

ommendations:

•Before operation of the device starts, get your-

self acquainted with the present manual and

the safety rules and regulations as well as the

recommendations specified by the manufac-

turer.

•Any other application of the device which has

not been determined within the present man-

ual may cause its damage and constitute a

source of danger for the user.

•The device should be operated solely by quali-

fied personnel who are properly authorised

and certified to realise measurements in elec-

tric installations. Should the tester be operated

by unauthorised persons, there is a danger of

damage to the device and the user.

•The device must not be applied to the network

and equipment within premises of special con-

ditions, e.g. in a dangerous atmosphere with

regard to explosion or fire.

•It is unacceptable to operate the following:

⇒A damaged meter which is completely or

partially out of order,

⇒A meter with damaged cable insulation,

⇒A meter stored for an excessive period of

time in disadvantageous conditions (e.g.

excessive humidity). If the meter has been

transferred from a cool to a warm envi-

ronment of a high level of relative humid-

ity, do not realise measurements until

the meter has been warmed up to the

ambient temperature (approximately 30

minutes).

•Do not operate a meter with an open or incor-

rectly closed battery (accumulator) compart-

ment or power it from other sources than those

specified in the present manual.

•Do not realise measurements for more than 30

seconds. After a 30-second measurement, the

next measurement may be realised not sooner

than after 240 s.

•The purpose of the signalling of limit values is

solely to warn the user and not to realise a

measurement.

Note:

The device may also be used during rain,

however at user’s own responsibility. It is

recommended to use gauntlets.

2 Measurements

2.1 Control of operation of the

tester

Before each use of the tester, it is necessary

to control its operation:

•The voltage indicator must be tested using a

known source of voltage,

•Close the measurement probes – there

should be an audible acoustic signal, the

LED Ωdiode should be on and the symbol

should appear on the display.

Remarks:

The voltage indication function is active when

the batteries are discharged or without batteries. In

order for the remaining functions to be active

charged batteries are required.

2.2 AC or DC voltage test

Note:

In the networks protected with an RCD switch

whose nominal current is 10mA or 30mA, it is pos-

sible that the switch is activated during a meas-

urement of voltage between L and PE. In order to

avoid that connect the tester between L and N and

after approximately five seconds switch the probe

from N to PE.

2.3 RCD operation test

In order to check the operation of the RCD

switch whose nominal current is 10mA or 30mA it

is necessary to realise a voltage test directly be-

tween the L phase and the protective cable PE.

2.4 One-pole phase testing

Note:

Attention!

Do not touch the electrode of the measurement

probe L1 during the testing of the phase.

In the case of one-pole determination of

phases for the purpose of specification of external

cables, under certain circumstances it is possible

that the operation of the tester will be impaired

(e.g. using insulated personal protection means or

in the case of an insulated work station).

One-pole phase testing may not be a sufficient

means to determine whether the circuit in question

is live. Do apply the two-pole voltage test.

2.5 Circuit continuity test

Note!

The measured object may be live.

Connect both the probes to the measured ob-

ject. An acoustic signal, lit Ωdiode and the symbol

appearing on the display indicate continuity

of the circuit (R<600kΩ).

Note:

During the measure of continuity polarization

of the voltage at the L2 probe is negative.

2.6 Measurement of resistance

Note!

The measured object may not be live.

Press shortly the Ωbutton and connect both

the probes to the measured object. Read the result

from the LCD display.

Note:

During the measure of resistance polarization

of the voltage at the L2 probe is negative.

2.7 The HOLD function

The purpose of the present function is to hold

the result of the measurement o the display. It is

possible pressing the HOLD button. In the left up-

per corner the

HOLD

symbol will be visible all the

time while the measuring instrument remains in

this mode.

Should the operator want to return to the nor-

mal measurement mode, they must press the

HOLD button again.

In the HOLD mode the Auto-OFF time will be

extended to 30 seconds.

2.8 Phase order test

Note:

The order of the phases may be determined

solely in a three-phase system.

2.9 Illumination of the measured

point

The P-2 tester offers the possibility of illumina-

tion of the measured area under difficult light con-

ditions (e.g. in switchgears). In order to illuminate

the measured point press the button marked with

the symbol . At the same time the LCD display

is backlit and it turns off automatically after ap-

proximately seven seconds.

The illumination may be also turned on when

the tester is off, and then three lines will appear on

the display.

Andere Handbücher für P-2

Inhaltsverzeichnis

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung