Sonic KSE-310 Bedienungsanleitung

KSE-310 TYPE FISH SIZING

ECHO SOUNDER

Instruction Manual

Ver. 5.04E

SONIC CORPORATION

<MEMO>

Battery Replacement Information

The computing unit of this system uses batteries for storing start-up information.

Replace the batteries periodically. Using batteries near the end of their life may cause

not only start-up failure, but also problems such as emitting smoke, catching fire or toxic

leakage.

Standard replacement time

The standard battery life is approximately 6 years. If the batteries are used at high

temperatures, the battery life will be shorter. We, therefore, recommend replacing the

batteries once every three to four years.

Replacement method

For the method of replacement, please contact our service staff.

Safety and Handling Instructions

Before using this system, please read this instruction manual carefully to

gain a thorough understanding and ensure safe and correct operation.

For system maintenance, please contact our repair and service staff.

Do not allow anyone except our repair and service staff to disassemble

and repair this system.

Please keep this manual on hand at all times.

Pictorial Symbols

In this instruction manual as well as on the product, pictorial symbols are provided

to indicate how to use our products correctly and to prevent injuries to users and

damage to their assets. Users are required to comply with the following instructions.

The indications of the pictorial symbols are as follows:

Indicates that “there is a high probability of causing death or

serious injury to users if not handled properly”

Indicates that “there is a risk of causing death or serious injury

to users if not handled properly”

Indicates that “there is a probability of causing moderate or

minor injury if not handled properly”

Batteries are valuable, recyclable resources. Please cooperate in recycling

used batteries.

Danger

Warning

Caution

Caution for installation sites

(1) Avoid using this system in a place that may reach high temperatures of

50°C or more, such as in direct sunlight or near heating systems for a long

period of time.

(2) Avoid using this system in a place that is humid or exposed to direct

splashes from waves.

Caution for inspections of the ship bottom and equipment

While inspecting the ship bottom, wear a helmet and safety shoes.

Inspections must be performed with two or more persons to ensure that contact

with the outside is possible, whenever necessary.

Warning

Danger

Prevention of an electric shock accident caused by the high-

pressure sections

(1) Before checking inside the system for maintenance and inspections, ensure

to turn OFF the power switch because some sections use high voltages.

(2) Before checking inside the system for maintenance and inspections, wash

your hands to remove any salt. If your working clothes and shoes are wet,

change them for dry ones.

(3) If someone around you is electrocuted, avoid direct contact because it may

lead to a risk of an electric shock. Alert everyone in a loud, calm voice, and turn

OFF the power switch or use a piece of wood to help. Then, use artificial

respiration or other general means of resuscitation.

 
3 
 
TABLE OF CONTENTS 
 INTRODUCTION..................................................................................I-7 
 OPERATION OVERVIEW...................................................................II-1 
2-1 Explanation of the controller ....................................................................................II-1 
2-2 Explanation of the screens .......................................................................................II-2 
2-3 Power ON and OFF ....................................................................................................II-3 
2-3-1 Power ON ...............................................................................................................II-3 
2-3-2 Power OFF .............................................................................................................II-3 
2-4 Adjust Gain.................................................................................................................II-4 
2-5 RANGE and SHIFT + Manual/Auto............................................................................II-5 
2-6 Displaying EXPANSION SCREEN.............................................................................II-7 
2-6-1 EXPANSION SCREEN DISPLAY ..........................................................................II-9 
2-6-2 EXPANSION SCREEN STRUCTURE .................................................................II-11 
2-7 Displaying A SCOPE................................................................................................II-13 
2-8 Displaying BOTTOM LINE.......................................................................................II-15 
2-9 How to use cursors..................................................................................................II-18 
2-9-1 H CURSOR...........................................................................................................II-19 
2-9-2 V CURSOR...........................................................................................................II-20 
2-10 Use of FISH LENGTH GRAPH and TS GRAPH....................................................II-22 
2-10-1 How to select fish schools ..................................................................................II-24 
2-10-2 How to make the graph more visible ..................................................................II-32 
2-10-3 Splitting the fish length detection range..............................................................II-36 
2-10-4 TS GRAPH setting..............................................................................................II-38 
2-11 How to use TRACE GRAPH ..................................................................................II-39 
2-11-1 How to display TRACE GRAPH .........................................................................II-39 
2-11-2 Trace graph display area....................................................................................II-41 
2-11-3 TRACE GRAPH setting......................................................................................II-43 
2-12 Biomass display.....................................................................................................II-44 

 
4 
 
2-12-1 Method of estimating the biomass .....................................................................II-44 
2-12-2 How to use Biomass display..............................................................................II-46 
2-13 How to use COLOR PATTERN .............................................................................II-50 
2-14 How to make the ES image easy to see ..............................................................II-52 
2-14-1 Changing the display color (color pattern) .........................................................II-52 
2-14-2 How to use the color clutter................................................................................II-54 
2-14-3 How to use INTERFERENCE REJECTION.......................................................II-55 
2-15 How to use MEMORY/REPLAY.............................................................................II-57 
2-15-1 REPLAY SETTING ............................................................................................II-57 
2-15-2 MEMORY SETTING ..........................................................................................II-58 
2-15-3 How to use REPLAY PICTURE.........................................................................II-59 
2-15-4 Items of REPLAY PICTURE ..............................................................................II-60 
2-15-5 Setting AUTO-RECORD SETTING ...................................................................II-63 
2-15-6 How to use auto-record......................................................................................II-64 
2-15-7 How to set saving...............................................................................................II-66 
2-15-8 How to check the available recording hour / recording size ..............................II-67 
2-16 Calibration..............................................................................................................II-69 
2-16-1 Calibration setting screen...................................................................................II-70 
2-16-2 Calibration parameter setting screen.................................................................II-72 
2-16-3 Screen structure at the start of the calibration ...................................................II-73 
2-16-4 CALIBRATION CONTROL window....................................................................II-74 
2-16-5 Calibration ball trace graph................................................................................II-76 
2-16-6 TR graph window ...............................................................................................II-77 
2-16-7 TR graph setting screen.....................................................................................II-78 
2-16-8 Cursor control window and depth window for the calibration.............................II-79 
2-16-9 Calibration work .................................................................................................II-81 
2-17 The user key...........................................................................................................II-89 
2-17-1 How to set the user key......................................................................................II-89 
2-17-2 How to use the user key.....................................................................................II-91 
2-18 Multi-frequency function.......................................................................................II-93 
2-18-1 Screen structure when using one display unit ...................................................II-93 
2-18-2 Screen structure when using two display units................................................II-101 
2-18-3 FREQ DIFF ......................................................................................................II-116 
2-18-4 ES ASSIGNMENT............................................................................................II-119 

 
5 
 
 EXPLANATION OF THE MENU ....................................................III-120 
3-1 Main menu .............................................................................................................III-120 
3-1-1 MEMORY/REPLAY ...........................................................................................III-121 
3-1-2 DISPLAY............................................................................................................III-121 
3-1-3 ES SETTING .....................................................................................................III-129 
3-1-4 SYSTEM............................................................................................................III-141 
3-1-5 TOOL.................................................................................................................III-145 
3-1-6 HELP..................................................................................................................III-147 
3-2 Shortcut menu.......................................................................................................III-150 
3-2-1 SCREEN SETTING...........................................................................................III-151 
1-(4) SEA BOTTOM HARDNESS..................................................................................III-152 
Olex................................................................................................................................III-152 
3-2-1 CURSOR CONTROL.........................................................................................III-156 
3-2-3 TX SETTING......................................................................................................III-157 
3-2-4 RX SETTING .....................................................................................................III-158 
3-2-5 SIGNAL PROCESS SETTING ..........................................................................III-160 
3-2-6 COLOR PATTERN SETTING ...........................................................................III-162 
 INTERFACE.......................................................................................IV-1 
4-1 J30 connector pin assignment ............................................................................... IV-1 
4-2 How to use EXTERNAL SYNC ................................................................................ IV-2 
4-2-1 Connection of the EXTERNAL SYNC signal........................................................ IV-2 
4-2-2 EXTERNAL SYNC signal standard ...................................................................... IV-2 
4-2-3 Menu setting .........................................................................................................IV-4 
4-3 EXTERNAL TRIGGER OUTPUT setting.................................................................. IV-6 
4-3-1 Connection of EXTERNAL TRIGGER OUTPUT signal........................................IV-6 
4-3-2 EXTERNAL TRIGGER OUTPUT signal standard................................................ IV-7 
4-3-3 Types and settings of the EXTERNAL TRIGGER OUTPUT signals....................IV-8 
4-4 Net depth gauge input setting .............................................................................. IV-10 
4-4-1 KNF(NMEA2) input.............................................................................................IV-10 
4-4-2 Net depth input ................................................................................................... IV-11 
4-5 NMEA input setting................................................................................................ IV-15 
4-5-1 NMEA input.........................................................................................................IV-15 
4-5-2 NMEA output ...................................................................................................... IV-16 

 
6 
 
4-6 Assigning J51 connector pins ..............................................................................IV-19 
4-6-1 ES signal output setting ......................................................................................IV-19 
4-6-2 Connecting the ES trigger output signals............................................................IV-20 
4-6-3 Standard for ES trigger output signals................................................................IV-20 
4-6-4 Connecting the ES output signals.......................................................................IV-21 
4-7 Installation .................................................................................................................IV-22 
4-7-1 CB25 Bridge to Tx/Rx .........................................................................................IV-22 
4-7-2 Transducer connection........................................................................................IV-22 
 TROUBLESHOOTING .......................................................................V-1 
5-1 Network.....................................................................................................................V-1 
5-2 Hardware problems: examples and measures.......................................................V-1 
5-3 Error message ...........................................................................................................V-3 
5-4 Alert messages..........................................................................................................V-4

Introduction

Echo sounders are designed to transmit sonic waves from a transducer and

receive the echo reflected from fish or the bottom of the sea. On previous echo

sounders, images were adjusted by the TVG volume and gain volume, so that

the reflected echo could easily be seen on the echo sounder picture.

This Fish Sizing Echo Sounder needs no TVG volume adjustment, and it

automatically and accurately corrects the sonic wave attenuation under the sea.

Fish schools of the same density are displayed in the same color regardless

of the depth. The features of this system are described below.

・Detection of a single fish with high accuracy.

・Controller designed for this system.

・Data recording function installed as the standard feature (row data)

・High precision digital TVG

・Function to determine the sea bottom level

・Supports a dual monitor

In addition, for fish length measurement, which is one of the features of this

system, the split beam method is adopted. The split beam method detects the

level of a single fish (only one fish) with a main receiving beam, and detects the

direction ofthis single fish with 4receiving beams. Bydetecting thefish direction,

the effect of the directive property that is peculiar to ultrasonic waves can be

corrected. Thus, fish length measurement free from the effects of directive

property is possible with high accuracy. For accurate fish length measurement,

please use the following information for reference.

(1) Outside noise reduction

The Fish Sizing Echo Sounder uses faint signals so that the measurement

accuracy can decrease when there is significant outside noise (running noise,

interference, etc.). For such cases, measures are available, such as reducing

I-8

the ship engine rotation to create an environment with less running noise, or

stopping audio systems that are not in use.

(2) Measurement accuracy enhancement

Making manymeasurements of the same fish school can enhance the accuracy

of the fish length. Examples of making such measurements include “reducing the

ship speed” and “changing the range of the Fish Sizing Echo Sounder to the

minimum value.”

<MEMO>

Inhaltsverzeichnis

Andere Sonic Schiffsausrüstung Handbücher

Sonic

Sonic 2024 Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Furuno

Furuno FE-800 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

Quicksilver

Quicksilver 88688A25 Handbuch

Furuno

Furuno Navtex NX-700-A Bedienungsanleitung

olympia electronics

olympia electronics ΒS-532/WP Bedienungsanleitung