Sonifex Phone In 6 Bedienungsanleitung

Phone In 6

User Handbook

Phone In 6 User Handbook

This handbook is for use with the following products :

Packages:

PI-6PSTN4 Phone In 6 system comprising 1 x PI-6C, 1 x PI-6R and 2 x PI-PSTN2

PI-6PSTN6 Phone In 6 system comprising 1 x PI-6C, 1 x PI-6R and 3 x PI-PSTN2

PI-6ISDN6 Phone In 6 system comprising 1 x PI-6C, 1 x PI-6R and 3 x PI-ISDN2

Components:

PI-6C Phone In 6 Base Console

PI-6R Phone In 6 Remote Control Panel

PI-PSTN2 Phone In 6 PSTN Card

PI-ISDN2 Phone In 6 ISDN Card

©Sonifex Ltd, 2010

Revision 1.01, August 2010

Sonifex Ltd, 61, Station Road, Irthlingborough,

Northants, NN9 5QE, England.

Tel: +44 (0)1933 650 700

Fax: +44 (0)1933 650 726

Email: [email protected].uk

Website: http://www.sonifex.co.uk

Information in this document is subject to change without notice and does not represent a commitment on the part of the

vendor. Sonifex Ltd shall not be liable for any loss or damage whatsoever arising from the use of information or any error

contained in this manual.

No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including

photocopying, recording, information storage and retrieval systems, for any purpose other than the purchaser’s personal

use, without the express written permission of Sonifex Ltd. Unless otherwise noted, all names of companies, products

and persons contained herein are part of a completely ctitious adaptation and are designed solely to document the use of

Sonifex product.

PHONE IN 6 USER HANDBOOK

Phone In 6 User Handbook

CONTENTS

Warranty i

Warranty and Liability i

Unpacking the Phone In 6 iii

Returning the Warranty Card iii

Safety Information iv

Safety of Mains Operated Equipment iv

Voltage Setting Checks iv

Fuse Rating iv

Power Cable and Connection v

Ordering the Correct Mains Lead vi

Installation Information vi

Atmosphere vi

Electromagnetic Radiation vi

WEEE & RoHS Directives - Sonifex Statement vii

Reporting Faults viii

Phone In 6 Introduction 1

Phone In 6 Operation 3

DSP Features Of The Phone In 6 System 3

Conferencing Calls & Use of the Cleanfeed/Mix-Minus 3

Call Handling - Self-op & Call Screening Modes 4

Self-op Mode 4

Auto-Answer & Auto-Drop Calls 4

Call Screening Mode 4

Receiving a Call 4

Routing a Call 5

Dropping a Call 5

Making a Call 5

Phone In 6 Conguration 5

Phone In 6 Menus 6

Phone In 6 Base Console Front Panel Controls & Indicators 8

Meters 8

Gain Controls 8

LED Indicators 8

Base Console Rear Panel 9

Telephone Interface Modules 9

Base Console Rear Inputs & Outputs 9

Music On Hold Input 9

Hybrid 1 (Conference) Input 9

Hybrid 1 Output 10

Hybrid 2 Input 10

Hybrid 2 Output 10

Link To Remote Panel 10

PSTN 1,2 & 3 Telephone Line Connectors 11

Ethernet Port 11

RS232 Serial port 11

Digital Audio Option 12

Audio Clocking 12

Remote Control Panel Controls & Indicators 13

Spinwheel Control & LCD Display 13

Numeric Keypad 13

LOCAL Button 14

LINE HOLD/Release Button 14

Phone In 6 User Handbook

CONTENTS & FIGURES

Figures

Table A : Packing List. iii

Table B : Power Connections. v

Table C : Mains Lead Table. vi

Fig 1-1: PI-6C Base Console Front View. 1

Fig 1-2: PI-6R Remote Control 1

Fig 1-3: System Block Diagrams 2

Fig 2-1a: Menu Structure Part 1 6

Fig 2-1b: Menu Structure Part 2 7

Fig 3-1: Base Console Front Panel 8

Fig 3-2: Meters 8

Fig 3-3: Gain Controls 8

Fig 3-4: Gain Controls 8

Fig 3-5: Base Console Rear Panel 9

Fig 3-6: Music on Hold Input 9

Fig 3-7: Hybrid 1 (Conference) Input 9

Fig 3-8: Hybrid 1 Output 10

Fig 3-9: Hybrid 2 Input 10

Fig 3-10: Hybrid 2 Output 10

Fig 3-11: Link To Remote Panel 10

Fig 3-12: PSTN Connectors 11

Fig 3-13: Ethernet Port 11

Fig 3-14: RS232 Serial Port 11

Fig 3-15: Remote GPI/O Port 12

Fig 3-16: Remote GPI/O Pins viewed from

rear of plug (or front of socket on unit) 12

Fig 3-17: IEC Mains Connector 12

Fig 4-1: Remote Control Panel Front 13

Fig 4-2: Spinwheel 13

Fig 4-3: Numeric Keypad 13

Fig 4-4: LOCAL Button 14

Fig 4-5: LINE HOLD/Release Button 14

Fig 4-6: ON AIR 1 Button 14

Fig 4-7: ON AIR 2 Button 14

Fig 4-8: Remote Control Panel Rear 15

Fig 4-9: Recessed Reset Button 15

Fig 4-10: LCD Contrast Adjustment 15

Fig 4-11: Local Headset 16

Fig 4-12: Link To Base Console 16

Fig 4-13: Ethernet Port 16

Fig 4-14: IEC Power Connector 16

Fig 5-1: Base Console Dimensions 17

Fig 5-2: Remote Control Panel

Dimensions 18

Contents (continued)...

ON AIR Button Hybrid 1 14

ON AIR Button Hybrid 2 14

Remote Control Panel Rear Panel Controls & Indicators 15

Reset Button 15

LCD Contrast Adjustment 15

Remote Control Panel Rear Inputs & Outputs 16

Local Headset 16

Link To Base Console 16

Ethernet Port 16

IEC Mains Input 16

Technical Specication

Product Dimensions 17

Base Console Dimensions (mm) 17

Remote Control Panel Dimensions (mm) 18

Technical Specication 19

Phone In 6 User Handbook i

WARRANTY

Warranty

Warranty and Liability

Important: the purchaser is advised to read this clause

(a) The Company agrees to repair or (at its discretion) replace Goods which are found to

be defective (fair wear and tear excepted) and which are returned to the Company

within 12 months of the date of despatch provided that each of the following

are satised:

(i) notication of any defect is given to the Company immediately upon its

becoming apparent to the Purchaser;

(ii) the Goods have only been operated under normal operating conditions and

have only been subject to normal use (and in particular the Goods must have

been correctly connected and must not have been subject to high voltage or

to ionising radiation and must not have been used contrary to the Company’s

technical recommendations);

(iii) the Goods are returned to the Company’s premises at the Purchaser’s expense;

(iv) any Goods or parts of Goods replaced shall become the property of

the Company;

(v) no work whatsoever (other than normal and proper maintenance) has been

carried out to the Goods or any part of the Goods without the Company’s prior

written consent;

(vi) the defect has not arisen from a design made, furnished or specied by

the Purchaser;

(vii) the Goods have been assembled or incorporated into other goods only in

accordance with any instructions issued by the Company;

(viii) the defect has not arisen from a design modied by the Purchaser;

(ix) the defect has not arisen from an item manufactured by a person other than

the Company.

In respect of any item manufactured by a person other than the Company, the Purchaser

shall only be entitled to the benet of any warranty or guarantee provided by such

manufacturer to the Company.

(b) In respect of computer software supplied by the Company the Company does not

warrant that the use of the software will be uninterrupted or error free.

ii Phone In 6 User Handbook

WARRANTY

(i) for death or personal injury to the extent that it results from the negligence of

the Company, its employees (whilst in the course of their employment) or its

agents (in the course of the agency);

(ii) for any breach by the Company of any statutory undertaking as to title, quiet

possession and freedom from encumbrance.

(d) Subject to conditions (a) and (c) from the time of despatch of the Goods from the

Company’s premises the Purchaser shall be responsible for any defect in the Goods

or loss, damage, nuisance or interference whatsoever consequential economic or

otherwise or wastage of material resulting from or caused by or to the Goods. In

particular the Company shall not be liable for any loss of prots or other economic

losses. The Company accordingly excludes all liability for

the same.

(e) At the request and expense of the Purchaser the Company will test the Goods to

ascertain performance levels and provide a report of the results of that test. The

report will be accurate at the time of the test, to the best of the belief and knowledge

of the Company, and the Company accepts no liability in respect of its accuracy

beyond that set out in Condition (a).

(f) Subject to Condition (e) no representation, condition, warranty or other term, express

or implied (by statute or otherwise) is given by the Company that the Goods are of

any particular quality or standard or will enable the Purchaser to attain any particular

performance or result, or will be suitable for any particular purpose or use under

specic conditions or will provide any particular capacity, notwithstanding that the

requirement for such performance, result or capacity or that such particular purpose

or conditions may have been known (or ought to have been known) to the Company,

its employees or agents.

(g) (i) To the extent that the Company is held legally liable to the Purchaser for any

single breach of contract, tort, representation or other act or default, the

Company’s liability for the same shall not exceed the Price of the Goods.

(ii) The restriction of liability in Condition (g)(i) shall not apply to any liability

accepted by the Seller in Condition (c).

(h) Where the Goods are sold under a consumer transaction (as dened by the Consumer

Transactions (Restrictions on Statements) Order 1976) the statutory rights of the

Purchaser are not aected by these Conditions of Sale.

Phone In 6 User Handbook iii

WARRANTY

Unpacking the Phone In 6

The Phone In 6 is shipped with the following equipment. Please check your packaging

to ensure that you have all of the items below. If anything is missing, please contact the

supplier of your equipment immediately.

Item Quantity Quantity Quantity

Phone In 6 Phone In 6 Phone In 6

PI-6PSTN4 PI-6PSTN6 PI-6ISDN6

PI-6C Base Console 1 1 1

PI-6R Remote Control Panel 1 1 1

PI-PSTN2 PSTN 2 Channel Module 2 3 -

PI-ISDN2 ISDN 2 Channel Module - - 3

IEC Mains lead 2 2 2

Handbook and warranty card 1 1 1

Headset 1 1 1

Table A : Packing List.

Each Phone In 6 is shipped in protective packaging and should be inspected for damage

before use. Where an item is found to have transit damage, notify the carrier immediately

with all the relevant details of the shipment. Packing materials should be kept for inspection

and also for if the product needs to be returned.

Returning the Warranty Card

In order to register the date of purchase so that we can keep you informed of any design

improvements or modications, it is important to complete the warranty registration

document that is enclosed and return it to Sonifex Ltd in the UK, or register online at

www.sonifex.co.uk/register

For your own records you should write down the serial number (which can be found on the

rear of the Phone In 6 or on the connector on the Phone In 6.

Serial Number ………………………………………

iv Phone In 6 User Handbook

SAFETY INFORMATION

Safety Information

Safety of Mains Operated Equipment

This equipment has been designed to meet the safety regulations currently advised

in the country of purchase and it conforms to the safety regulations specied by

use of the CE Mark.

Warning : There are no user serviceable parts inside the equipment. If you should ever

need to look inside the unit, always disconnect the mains supply before removing the

equipment covers.

Warning: In the UK the Phone In 6 phone line socket should only be connected with

apparatus complying with BS6301, and the connection to the network must not be hard

wired Interconnection directly or indirectly with equipment ports marked in accordance

with BS6301 to unmarked ports may produce hazardous conditions on the network and

advice should be obtained from a competent engineer before such a connection is made.

Warning: This apparatus must be earthed by means of the earth connector on the rear

panel, and the connection to the telecommunications network should be removed

before disconnecting the earth. Disconnection of this earth connection may render the

equipment unsafe, with a consequential possible electrical shock hazard from exposed

metallic parts.

Warning: The barriered ports ‘PSTN’and ‘ISDN’ must not be connected directly or

indirectly to the un-barriered ports, ‘MUSIC ON HOLD’, ‘HYBRID 1/2 INPUT/OUTPUT’,

‘REMOTE GPI/O’ or ‘RS-232’.

Voltage Setting Checks

The integral power supply is designed to accept a universal input of 85 to 264 VAC mains

input voltage. The safety specication of your Phone In 6 complies with local requirements

and must be earthed through the mains connector.

Fuse Rating

The Phone In 6 is supplied with a single fuse in the live conducting path of the mains

power input. For reasons of safety it is important that the correct rating and type of fuse is

used. Incorrectly rated fuses could present a possible re hazard, under equipment fault

conditions. The fuse rating for Phone In 6 is:

85V - 264V AC operation - 1A 5 x 20mm SB

The active fuse is tted on the outside rear panel of the unit.

Phone In 6 User Handbook v

SAFETY INFORMATION

Power Cable and Connection

An IEC power connector is supplied with the Phone In 6 which has a moulded plug attached

– this is a legal requirement. If no moulded plug has been supplied with your Phone In 6,

please contact your supplier, because an IEC connector is always supplied from the Sonifex

factory.

If for any reason, you need to use the Phone In 6 with a dierent power cable, you should

use the following wiring guidelines

Wire Colour Connection

Green, or green and yellow Earth (E)

Blue, or Black Neutral (N)

Brown, or Red Live (L)

Table B : Power Connections.

Connect the equipment in accordance with the connection details and before applying

power to the unit, check that the machine has the correct operating voltage for your mains

power supply.

Important Note : The terminal marked on the rear panel must be earthed.

vi Phone In 6 User Handbook

Ordering the Correct Mains Lead

When ordering a TBU from Sonifex, it is helpful if you can specify your required operating

voltage and mains lead. After the product code add:

UK, for 230V, UK 3 pin to IEC lead

EC, for 230V, European Schuko 2 pin to IEC lead

US, for 115V, 3 pin to IEC lead

AU for 230V, Australasian 3 pin to IEC lead

Table C : Mains Lead Table.

E.g. order PI-6PSTN4 UK for a UK IEC lead to be supplied.

Installation Information

Atmosphere

The units should be installed in an area that is not subject to excessive temperature

variation (<0°C, >50°C), moisture, dust or vibration.

Electromagnetic Radiation

The cover is connected to earth by means of the xing screws. It is essential to maintain

this earth ground connection to ensure a safe operating environment and provide

electromagnetic shielding.

SAFETY INFORMATION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sonifex Telefonsystem Handbücher

Sonifex

Sonifex DHY-04 Bedienungsanleitung

Beliebte Telefonsystem Handbücher anderer Marken

Teleco

Teleco Perfect Voice Tis 16 Bedienungsanleitung

AT&T

AT&T Network Adapter 25 Bedienungsanleitung

AVE

AVE AF902R-CE Bedienungsanleitung

Tynetec

Tynetec Advent xt Bedienungsanleitung

Ericsson

Ericsson DCT1800-S Bedienungsanleitung

NEC

NEC Electra Elite 192 Bedienungsanleitung

Alcatel

Alcatel EASY REFLEXES 4200 Bedienungsanleitung

Panasonic

Panasonic KX-TDA50 Bedienungsanleitung

Bticino

Bticino PABX 28D Bedienungsanleitung

NEC

NEC SL 2100 Bedienungsanleitung

TransTel Communications

TransTel Communications TD-824i Montageanleitung

Nortel

Nortel BCM50 Produkthandbuch

Panasonic

Panasonic KX-TS25B Bedienungsanleitung

ASCOM

ASCOM TD 92375GB Betriebsanleitung

Karel

Karel MS26S Produktinformationsblatt

EnGenius

EnGenius DuraFon PRO Bedienungsanleitung

Teledat

Teledat X130 DSL Bedienungsanleitung

SpectraLink

SpectraLink MOG400 Bedienungsanleitung