Sony Ericsson CMD-Z7 Bedienungsanleitung

6(59,&(0$18$/

$(30RGHO

8.0RGHO

SPECIFICATIONS

Signalling format Dual-Band

Frequency range E-GSM 900 MHz, Transmit: 880 ~ 915 MHz

Receive: 925 ~ 960 MHz

GSM 1800 MHz, Transmit: 1710 ~ 1785 MHz

Receive: 1805 ~ 1880 MHz

GSM 900 power class Class 4 (2W)

GSM 1800 power class Class 1 (1W)

SIM 3V and 5V Pluggable mini SIM card / SAT Class 2

Display High resolution full graphics display

4 Grey-scale type

Resolution: 96 x 92 pixels

7 lines (excluding 1 status icon line), proportional font

Channel spacing 200 kHz

Number of channels E-GSM 900: 174

GSM 1800: 374

Frequency stability Transmit frequency drift (synchronized)

< 0,1 p.p.m

Antenna type Patch antenna

RF output power E-GSM 900: 2W, 33dbm

GSM 1800: 1W, 30dbm

Battery Lithium Polymer / 680 mAh

Standby : 50 -220 h (Network dependent)

Talk time : 2.6 - 8 h (Network dependent)

Dimensions 91 mm x 50 mm x 25 mmñ

Weight 95 g

Volume 90 cmñ

3257$%/(',*,7$/&(//8/$57(/(3+21(

:,7+$&&(6625,(6

Power requirements 3.9 V (nominal)

Operating temperature -10C to +55C

Accessories operating temperature ± 0C to +45C

Connectors External RF connector

Universal Connector (12-pin flat I/O connector)

Mini plug head set jack

WAP Supported by the WAP v.1.1 compliant browser

WTLS Class 1, HTTP/HTML

Email Supported by the e-mail protocols: SMTP & POP 3

Supplied accessories AC Adapter QN-3AC1 (AEP)

AC Adapter QN-3AC2 (UK)

Battery (std.) QN-Z7BPS

Optional accessories Handsfree Car Kit QN-3HFK

Car Phone Holder QN-Z7PH

Cigar Lighter Charger QN-3CC

Data Cable RS QN-3RS

Data Cable USB QN-3USB

Mobile Data Software QN-3DS

Headset QN-3HS

Travel Charger QN-3TC

Design and specifications are subject to change without notice.

This equipment complies with the essential requirements of the Directive 1999/5/EC Radio and

Telecommunications Terminal Equipment Directive.

NOTE

This device contains electrostatically sensitive components. Damage can occur to these

components if the appropriate handling is not adhered to.

ESD Handling precautions:

A working area in which Digital Cellular Telephones may be safely handled without undue risk of damage

from electrostatic discharge must be available.

The area must be equipped as follows:

½All working surfaces must have a dissipative bench mat, safe for use with live equipment, connected

via 1.2M•resistor to a common ground point.

½A quick release skin contact device with a flexible cord, which has a built-in safety resistor of a range

between 5.2K•Ωand 1.2MΩ•shall be used. The flexible cord must be attached to a dissipative earth

point.

½All containers and storage must be of the conductive type.

Batteries:

This device contains an internal battery in addition to the external battery pack. These batteries are

recyclable and should be disposed of in accordance with national legislation. They must not be incinerated,

or disposed of as ordinary rubbish.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended

by the manufacturer.

Discard used batteries according to the manufacturer’s

instructions.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

ADVARSEL

Eksplosjonsfare ved feilaktig skifte av batteri.

Benytt samme batteritype eller en tilsvarende type

anbefalt av apparatfabrikanten.

Brukte batterier kasseres i henhold til fabrikantens

instruksjoner.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en likvärdig typ som

rekommenderas av apparattillverkaren.

Kassera använt batteri enligt gällande föreskrifter.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda

paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

TABLE OF CONTENTS

SECTION 1

Specifications ……………………………………………………… (see Cover sheet)

SECTION 2

General Descriptions

2.1 Multi Band ………………………………………………………. 04

2.2 Radio Frequency Power Level ……………………………….. 05

2.3 Speech Codec …………………………………………………. 05

2.4 Languages ……………………………………………………….05

2.5 Battery Charging ……..………………………………………… 06

2.6 Battery Safety ……………………………………………………06

2.7 Battery Capacity ….…………………………………………….. 06

2.8 Accessory Interface ..…………………………………………... 07

SECTION 3

Operating Instructions

3.1 Basic Features …………………………………………………..08

3.2 Security Codes ………..…………………………………………09

3.3 Icon Glossary …………………………………………………… 10

3.4 Menu Overview ………………………………………………….10

3.5 Applications Menu ……………………………………………… 10

SECTION 4

Disassembling/Testing

4.1 Disassembly ……………………………………………………..11-13

4.2 Interface to GSM-Tester ………………………………………..14

4.3 Jigs and Tools…………………………………………………… 15

SECTION 5

Programming Instructions

5.1 Requirement ..……………………………………………………16

5.2 Hardware Set-up ..…...………………………………………….16

5.3 Software Set-up .………………………………………………...16

5.3.1 Software Download to Mobile ………………………………. 16-17

5.3.2 Save Personal Data in Mobile ……………………………….17

5.3.3 Reset of Personal Data ……………………………………… 17

5.3.4 Reset of Security Lock ………………………………………. 17

SECTION 6

Explosion View

6.1 Spare Parts List ………………………………………………… 18

6.2 Accessories ……………………………………………………...19

SECTION 2

GENERAL DESCRIPTIONS

2.1 Multi-band :

CMD-Z7 support E-GSM 900 and GSM 1800 multi-band functionality.

For the use in Europe and in other countries worldwide, ETSI has specified GSM standards into two frequency

bands. That is the 900-MHz and 1800-MHz band and is usually referred to as GSM900 and GSM1800 (formerly

DCS1800).

While the 900-MHz band has 124 channels (extended version: 175), the 1800-MHz band with its 375 channels

provides a three-times higher capacity. Not only as a result of this large range of channels but also due to the low

transmission power and the transmission distance, GSM1800 supports a higher quantity of RF-channels.

The Dual band technology enables a network operator with spectrum at both 900MHz and 1800MHz to support the

seamless use of dual band handsets across both frequencies. By supporting seamless handovers between

900MHz and 1800MHz, Dual band networks can provide major benefits in terms of capacity enhancement and

revenue optimisation through the introduction of new services.

The CMD-Z7 is a phase II, GSM900 class 4, GSM1800 class 1 mobile phone.

The nominal maximum output power for GSM900 is 2W, for GSM1800 1W.

It supports the extra functionality required for multi-band mobile stations: Inter-band/”seamless” hand-over,

channel assignment, cell selection and re-selection, all between both bands within a Public Land Mobile Network.

The manual and automatic PLMN selection in both bands is given.

The user does not need any special action to use the multi-band functionality of the phone.

Users are able to manually roam between PLMN’s operating in E-GSM900 and GSM1800 bands.

E-GSM

With the further development of the GSM standard, an additional range of frequencies has been made available to

the “Global system for mobile communications”. For each of the two duplex frequency ranges, one for the forward

direction and one for the reverse direction, additional 10 MHz have been added to the bottom end of the bands,

extending the frequency range to 50 further channels.

The mobile station transmits in the 880- to 915 MHz range, and the base station transmits in the 925- to 960 MHz

range. A duplex spacing of 45 MHz is used, the base station always transmits on the high side of the duplex

frequency pair.

The numbering for these additional channels is from 974 to 1023. This is done to avoid assigning one channel

number twice within the same standard.

Compared to the primary GSM system, Channel number 0 is used in the extended GSM system, since it does not

make sense to reserve it at a guard band within the E-GSM bands. Now, the lowest channel, number 974 (880.0

MHz), serves as the guard band between GSM and other services on lower frequencies.

GSM 1800

GSM-1800 uses the frequency ranges of 1710 to 1785 MHz in the uplink direction, and 1805 to 1880 MHz in the

downlink direction.

From these figures it follows that the duplex spacing is 95 MHz with 374 channels with bandwidths of 200 kHz

each.

The channels are numbered from 512 to 885 in order to distinguish them from the channels in the primary and

extended GSM frequency bands.

2.2 Radio Frequency Power Levels:

Between the GSM1800 and the E-GSM System are differences regarding the power level. GSM1800 basically

needs lower power levels. If the performance of a MS for GSM900 system was certified of 2W (Power Class 4),

then in the GSM1800 system it is only 1W (Power Class 1). There are also reduced BTS power levels due to

microcell applications, which means instead of the 40W (Power Class 4) in the E-GSM900 system GSM1800

needs only 20W (Power Class 1).

2.3 Speech Codec

The CMD-Z7 supports the following speech codecs.

•

Full Rate (FR) Codec

•

Half Rate (HR) Codec

•

Enhanced Full Rate (EFR) Codec

The speech codec forms the human voice into a digital signal, which is sent in the GSM network.

The GSM system currently has three different speech codec standards.

At first, the Full Rate (FR) Codec was introduced. With new requirements concerning speech quality and

availability of radio channel resources two further standards were introduced, the Half Rate (HR) Codec and the

Enhanced Full Rate (EFR) Codec. The Half Rate (HR) Codec requires only half the channel capacity of a Full Rate

(FR) Channel. The Enhanced Full Rate (EFR) Codec requires the same radio channel resources as a Full Rate

(FR) Codec but offers Fixed Line quality with superior vocal clarity.

2.4 Languages

The CMD-Z7 supports the following languages:

•Bulgarian •French •Portugese

•Croatian •German •Romanian

•Czech •Greek •Russian

•Danish •Hungarian •Slovakian

•Dutch •Italian •Slovenian

•English •Norwegian •Spanish

•Finnish •Polish •Swedish

•Turkish

Preferences GSM 900 E-GSM GSM 1800

Frequency band

uplink:

downlink:

MHz

890 - 915

935 - 960

MHz

880 - 915

925 - 960

MHz

1710 -1785

1805 - 1880

Radio Channels 124 174 374

max. BS-Power 40 W (46 dBm) 20W (43 dBm)

max. MS-Power 2 W (33 dBm) 1W (30 dBm)

2.5 Battery Charging

There is no charging circuitry in the battery pack. The CMD-Z7 has complete charger function internally.

The telephone can be charged only with the battery connected the phone. This situation can be sub-divided into

two situations: the phone is on or off. It can be charged with the AC Adapter, Travel Charger or Cigar Lighter

Charger.

The battery symbol is used to indicate the charging, and to indicate when the battery is fully charged. This is done

using the following sequence of icons:

The uncharged segments of the battery are moving in a right to left manner until the charging stops. The

sequences for each charging level is repeated until the battery is charged to that level.

When the charging sequence is finished the flashing of the battery level sign stops.

The phone shows the full-battery icon.

Note: When the battery pack is completely discharged, it can take some time until the battery icon appears when

charging

2.6 Battery Safety

The battery pack contains a single Li-polymer cell, a safety circuitry and, in addition, a microprocessor unit which

manages RTC information by reading out the binary counter value in the microprocessor. The charging circuitry

and the safety circuitry together guarantee a double fail-safe battery pack. This means that each component can

be either short or open and still all the safety requirements will not be violated.

The safety concept protects against:

Over voltage: The charging is stopped when Battery Voltage (Vbat) reaches 4.27V- 4.3V. The charging resumes

when Vbat falls below (4.045V - 4.145V).

Under voltage: When the cell voltage drops below 2.242V – 2.358V the cell is disconnected for discharging.

Charging is still possible.

Current fuse: Finally, if all protection functions are out of order due to abnormal condition, the current fuse protects

the device from explosion and fire with melting. The fuse melts 10A during 1 second.

2.7 Battery Capacity

QN-Z7BPS 680mAh; Lithium Polymer Technology

The phone can be charged even during making phone calls.

However, the shortest charging time will be reached when the phone is switched off.

2.8 Accessory interface

The table explains what kind of pins the phone supplies to the different accessories.

Pins GND

Charge

GEN

I/O

Power

OUT

(IN)

(OUT)

ACC

RS232

RTS

RS232

CTS

Audio

Out

Audio

AGND

Charger √√

CLC √√

HFK √√√ √√√√

Data Cable RS √√√√√√√√

Data Cable USB √√√√√√√√

Connector layout

The connector comprises the following pins:

Audio

Audio In, Audio Out and Audio GND:

Audio IN:

Is a single ended input with a maximum sensitivity of 365 mVrms.

Audio OUT:

The single ended output delivers 0.8Vpp into a 1kΩload.

These two signals are referred to as AGND.

RS232 Interface

5-pin interface: RX, TX, RTS(RFR), CTS and Gen I/O(DTR or DCD):

This is the communication interface to the Data cable “QN-3RS/USB”.

Pin 3 is connected to a general IO pin on the baseband digital chip. The functionality can be assigned on an

accessory by accessory basis to be input, output or interrupt.

Charge

The Charge pin represents the positive contact for the charging funtionality.

GND

The Ground pin represents the digital interface and charger return current.

This pin shows the presence of an accessory and is also an analog ID for the accessory. Accessories which

provide charger functionality only, do not support this pin and their presence is detected with a valid charger

voltage.

Power Out

Power-out has a different functionality with different accessories.

In the car-kit environment the ext. Vbat indicates that a phone call is accepted/in progress. This information is used

by the car-kit to power up the audio section of the car-kit, mute the car stereo and keep the car-kit powered up

even when the ignition is switched off.

Due to the fact that the ID of the accessory is detected first, the ACC power is not current limited (protected).

Connector view from base of phone





SECTION 3

OPERATING INSTRUCTIONS

3.1 The Basic Features of the CMD-Z7

•Parts and Controls

This section provides a brief guide to the operation and facilities available on the CMD-Z7. Refer to the Operating Manual for full

operational information.

•Jog Dial

The Jog Dial provides fast and easy menu navigation with only one hand.

Operation Function Function

Rotate the Jog Dial clockwise Scrolls through menu options.

or counter-clockwise Opens Phonebook in Standby Mode.

Press the Jog Dial straight Opens Menu in Standby Mode.

into the phone Selects an option (highlighted in the display)

Keep the Jog Dial pressed Dials the phone number selected.

Press the Jog Dial forward Exits from one menu to the previous screen.

Also ends a call.

Press the Jog Dial backward Opens the “pop up menu”.

Also opens help.

1 Ear piece

2 Advanced Jog Dial

3 Voice Mail Key

4 Keypad

5 Microphone

6 Flip

7 Display

8 Send Key

9 Memo Key

Clear Key

11 On/Off Key

Call End Key

12 External Antenna Connector

13 Headset Connector

14 Finger Stop

15 Loudspeaker

16 Battery Cover

17 Charging Indicator

18 Battery Release Button

19 External connector

(Charging and Accessories)

•Loudspeaker

vDuring a call, press the Jog Dial backward and select Loudspeaker to turn the loudspeaker on/off.

•The Voicemail Key

vPress and hold to access your Voicemail

•Manner Mode

vIn standby mode when the flip is closed, press the Jog Dial backward to activate/deactivate the

manner modes.

vOnce selected, it is possible to switch among the manner mode functions. All manner mode icons

appear in the display; rotate the Jog Dial to select one:

3.2 Security Codes

CODE TYPE NUMBER OF

DIGITS DESCRIPTION

Personal Identification Number 4 to 8 Controls SIM security. Supplied by the

Service Provider !

PIN 2 4 to 8 Controls memory security. Supplied by the

Service Provider !

PIN / PIN 2

Personal Unblocking Key

(PUK / PUK 2) 8

Used to unblock PIN and PIN 2.

A PIN or PIN 2 will become blocked if the wrong

PIN or PIN 2 is entered three times.

When the blocked PIN or PIN 2 is unblocked, a

new PIN or PIN 2 must be entered. If the wrong

PUK or PUK 2 is entered 10 times, the SIM card

will be unusable.

Supplied by the Service Provider !

Bearing Password 4

Controls the call bar function. If the wrong

password is entered three times, this

service will be revoked.

Supplied by the Service Provider !

Security Code 4 to 8 Controls the access to wap-and e-mail settings.

The default Security Code is: 0000

Refer to Section 5 “Programming Instructions”

Silent Mode :turns the ringer and all tones to silent mode.

Ringer to Single beep :ringer is restricted to a discrete single beep.

Vibra Alert :Vibra Alert without the ringer.

Outdoor :turns the ringer and all tones to the maximal volume.

3.3 Icon Glossary

3.4 Menu Overview 3.5 Applications Menu

Press the Jog Dial from standby mode to Press the Jog Dial backward from standby mode to

access the Main menu: access the Applications menu:

ICON Explanation

Network not available

Network signal strenght (strong)

Battery strength

SMS (Envelope Icon)

Voicemail

Alarm

Silent Mode

Vibra Alert

Single Beep

Outdoor Mode

Ringer off

Conversation Privacy (ciphering) not supportet

T9 (Text editing system)

Paste

ICON Explanation

Missed calls

Incoming call barring

Outgoing call barring

Incoming + Outgoing call barring

Conditional Divert

Unconditional Divert

Active call

Call hold

Mute Microphone

Headset connected – active call

Handsfree Kit connected (auto answer on)

Loudspeaker on

Press theJog Dial backward (pop-up menu)

Inhaltsverzeichnis

Andere Sony Ericsson Handy Handbücher

Sony Ericsson

Sony Ericsson WALKMAN W205 Bedienungsanleitung

Sony Ericsson

Sony Ericsson Xperia X10 Mini Pro Service-Handbuch

Sony Ericsson

Sony Ericsson K630i Bedienungsanleitung

Sony Ericsson

Sony Ericsson Walkman W380 Bedienungsanleitung

Sony Ericsson

Sony Ericsson STICK MICRO W995 Programmierhandbuch

Sony Ericsson

Sony Ericsson K770 Bedienungsanleitung

Sony Ericsson

Sony Ericsson T206 Bedienungsanleitung

Sony Ericsson

Sony Ericsson Walkman W580i Bedienungsanleitung

Sony Ericsson

Sony Ericsson Walkman W760i Bedienungsanleitung

Sony Ericsson

Sony Ericsson K500 Series Bedienungsanleitung

Sony Ericsson

Sony Ericsson ST18i Technisches Handbuch

Sony Ericsson

Sony Ericsson Cyber-shot C905 Bedienungsanleitung

Sony Ericsson

Sony Ericsson G900c Kurzanleitung

Sony Ericsson

Sony Ericsson k310c Bedienungsanleitung

Sony Ericsson

Sony Ericsson W21S Installationsanleitung

Sony Ericsson

Sony Ericsson C903U Cyber-shot Bedienungsanleitung

Sony Ericsson

Sony Ericsson W610c Bedienungsanleitung

Sony Ericsson

Sony Ericsson Xperia X2 Bedienungsanleitung

Sony Ericsson

Sony Ericsson T612 Kurzanleitung

Sony Ericsson

Sony Ericsson EXPERIA Mini ST15i Referenzhandbuch

Sony Ericsson

Sony Ericsson Z300a Bedienungsanleitung

Sony Ericsson

Sony Ericsson Z200 Handbuch

Sony Ericsson

Sony Ericsson K530 Kurzanleitung

Sony Ericsson

Sony Ericsson K790 Einrichtungshandbuch

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung