Sony CBK-SD01 Bedienungsanleitung
SDI OUTPUT BOARD
CBK-SD01
INSTALLATION MANUAL
1st Edition
CBK-SD01
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr undVerletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
CBK-SD01 1
Table of Contents
1. Installation
1-1. CBK-SD01 Configuration ..................................................................... 1-1 (E)
1-2. Applicable Models for Installation........................................................ 1-1 (E)
1-3. Installation Procedure............................................................................ 1-1 (E)
1-4. Opening and Closing the Inside Panel .................................................. 1-2 (E)
1-5. Installing the CBK-SD01 (DIF-147 Board) ..........................................1-3 (E)
1-6. Select Output Signal .............................................................................. 1-5 (E)
1-1 (E)
CBK-SD01
1-1. CBK-SD01 Configuration
The CBK-SD01 consists of the following:
.DIF-147 board (1)
.B2 x4 (2)
.Precision screw P1.4 x3.5 (2)
.Installation Guide (1)
.Installation Manual (1)
In addition to the Installation Manual, the following manuals are available.
.PDW-510/510P/530/530P Operation Manual (Supplied with PDW-510/510P/530/530P)
This manual is necessary for application and operaion of PDW-510/510P/530/530P.
Part number: 3-205-742-0X
.MSW-900/900P Operation Manual (Supplied with MSW-900/900P)
This manual is necessary for application and operaion of MSW-900/900P .
Part number: 3-206-082-0X
.
PDW-510/510P/530/530P, CBK-SD01 Maintenance Manual (Available upon request)
This manual intended for use by trained system and service engineers describes (the circuit overview,
character display functions, the main part replacements, electrical alignment, parts list, semiconductor
pin assignments, block diagrams, schematic diagrams, board layouts, etc.) required for parts-level
service.
For obtaining, contact your local Sony Sales Office/Service Center.
Part number : 9-968-032-71
1-2. Applicable Models for Installation
.PDW-510/510P/530/530P
.MSW-900/900P
1-3. Installation Procedure
Outline of the installing the CBK-SD01 to the PDW-510/510P/530/530P, MSW-900/900P is listed as
follows. For the details of the installation work, refer to the respective sections.
Installation procedure Sections describing the detailed procedure
1. Opening the Inside Panel 1-4. Opening and Closing the Inside Panel
2. Installing the CBK-SD01 (DIF-147 Board) 1-5. Installing the CBK-SD01 (DIF-147 Board)
3. Closing the Inside Panel 1-4. Opening and Closing the Inside Panel
4. Operation Check 1-6. Select Output Signal
Select the output signal with the use of menu.
Confirm that the SDI singal is output from the
VIDEO OUT terminal.
Section 1
Installation
1-2 (E) CBK-SD01
1-4. Opening and Closing the Inside
Panel
Opening the Inside Panel
n
Be sure to turn off the POWER switch, unplug the AC
power cord or remove the battery before starting the
following procedure to prevent the inside of the unit from
damage.
1. Loosen the four screws (with drop-safe) and open the
inside panel in the direction of the arrow.
m
.Folding the flexible card wire connected to the FP-
140 board (the FP-121A board for MSW-900/900P)
shortens the life of the flexible card wire significant-
ly. Be very careful when handling the flexible card
wire not to fold it.
.To install CBK-SD01 in MSW-900/900P, place the
unit so that the inside panel is positioned on top of
the POWER switch when the inside panel is opened.
Flexible card wires
Inside panel
FP-121A board
Inside panel Hook
Hinge
POWER switch
Hinge
Hook
Screw
(with drop-safe)
Screw (with drop-safe)
Screws
(with drop-safe)
Flexible card wires
Inside panel
FP-140 board
Hook
Hinge
Hinge
Hook
Screw
(with drop-safe)
Screw (with drop-safe)
Screws
(with drop-safe)
PDW-510/510P/530/530P is shown. MSW-900/900P is shown.
1-3 (E)
CBK-SD01
Closing the Inside Panel
1. Confirm that both of the right and left hinges are
engaged with the hooks of the chassis correctly.
2. Attach the inside panel and fix it with the four screws
(with drop-safe).
n
Standard tightening torque value :
Screw (with drop-safe, B3 x12)
0.8 N.m (8.0 kgf.cm)
n
Be careful not to pinch the harness between the inside
panel and chassis.
1-5. Installing the CBK-SD01 (DIF-147
Board)
1. Disconnect the coaxial cable form the connector
(CN10) on the DCP-36 board (the DCP-32 board for
MSW-900/900P).
n
To disconnect the coaxial cable, do not attempt to
disconnect it by pulling the cable with force. Be sure
to hold the plug and disconnect the cable.
CN10
Coaxial cable
DCP-36 board
Hold the plug to
remove.
OK Do not atempt to
remove by pulling
the cable.
NG
The illustration shows the PDW-510/510P/530/530P.
1-4 (E) CBK-SD01
2. Insert the connector (CN2) of the CBK-SD01 (DIF-
147 board) to the connector (CN2) on the DCP-36
board (the DCP-32 board for MSW-900/900P) and fix
it to the supports with the two screws supplied.
n
Standard tightening torque value :
Screw P1.4 x3.5
0.1 N.m (1.0 kgf.cm)
Screw B2 x4
0.19 N.m (1.9 kgf.cm)
3. Connect a coaxial cable that is removed in step 1, to
the connector (CN1) on the CBK-SD01 (DIF-147
board).
CBK-SD01
Coaxial cable
CN2
CN1
CN3
DCP-32 board
Supplied screws
(P1.4 x3.5)
Supports
CBK-SD01
CN2
CN1
Coaxial cable
DCP-36 board
Supplied screws
(B2 x4)
Supports
CN2
PDW-510/510P/530/530P is shown. MSW-900/900P is shown.
1-5 (E)
CBK-SD01
1-6. Select Output Signal
Select the output signal following the steps as shown below.
Identifying switches
1. Turn on the main power.
2. While pressing the rotary encoder, set the MENU ON/OFF switch to ON to open the TOP
menu.
3. Select the OPERATION menu and press the rotary encoder.
4. Select the OUTPUT display and press the rotary encoder.
5. Move the cursor (→) to REAR BNC SEL and press the rotary encoder to select SDI.
6. Turn off the main power.
CANCEL/PRST
OFF
ON ESCAPE
MENU
ON/SEL
OFF
STATUS
Rotary
encoder
STATUS ON/
SEL/OFF switch
MENU ON/OFF
switch
MENU CANCEL/PRST/
ESCAPE switch
The illustration shows the PDW-510/510P/530/530P.
Andere Handbücher für CBK-SD01
1
Inhaltsverzeichnis
Andere Sony Camcorder Handbücher
Sony
Sony DCR-TRV140 - Digital8 Camcorder With 2.5"... Bedienungsanleitung
Sony
Sony CVX-V18NS Bedienungsanleitung
Sony
Sony Handycam DCR-SR33E Bedienungsanleitung
Sony
Sony DCR-SR300 Benutzerhandbuch
Sony
Sony CCD-CR1 - Video Camera Recorder 8mm Bedienungsanleitung
Sony
Sony Handycam CCD-TR31 Bedienungsanleitung
Sony
Sony Handycam HDR-SR10 Bedienungsanleitung
Sony
Sony XDCAM PDW-F75 Bedienungsanleitung
Sony
Sony Handycam DCR-TRV230E Bedienungsanleitung
Sony
Sony DCR-HC65 - Digital Handycam Camcorder Bedienungsanleitung
Sony
Sony Handycam DCR-PC105 Bedienungsanleitung
Sony
Sony Handycam CCD-F77 Bedienungsanleitung
Sony
Sony Handycam DCR-PC9 Bedienungsanleitung
Sony
Sony Handycam HDR-PJ50V Bedienungsanleitung
Sony
Sony HXR-MC1 Brochure Bedienungsanleitung
Sony
Sony CCD-TR66 - Video Camera Recorder 8mm Bedienungsanleitung
Sony
Sony XCL-U1000 Bedienungsanleitung
Sony
Sony Handycam HDR-FX7 Bedienungsanleitung
Sony
Sony FS700 Bedienungsanleitung
Sony
Sony DSR-250 Bedienungsanleitung
