Sony DSR PD170 - Camcorder - 380 KP Bedienungsanleitung

Quick Start Guide

This guide introduces you to the basic way of recording/playback.

AC Adaptor (supplied)

Connecting the power cord

Use the battery pack when using your camcorder outdoors

Connect the plug with its vmark

facing toward the LCD panel side.

Open the DC IN jack

cover.

Inserting a cassette

1While pressing

the small blue

button on the

EJECT switch,

slide it in the direction

of the arrow.

Push the middle

portion of the back of

the cassette to insert it.

Insert the cassette into

the cassette

compartment with the

window facing out

and the write-protect

tab facing upward.

3Close the cassette

compartment by

pressing the PUSH

mark on it.

PUSH

Window

Installing the microphone

Install the supplied microphone with the model name (ECM-NV1) facing upward. Be sure

to connect the microphone plug to the INPUT1 connector.

4Close the cassette lid

by pressing the

PUSH button on the

cassette lid.

Write-protect tab

to INPUT1

<<3>>

Quick Start Guide

4Press START/

STOP. Your

camcorder starts

recording. To stop

recording, press

START/STOP

again.

Recording a picture

Monitoring the playback picture on the LCD

screen

1Set the POWER switch to

VCR while pressing the

small green button.

2Press mto rewind

the tape.

3Press Nto start

playback.

NOTE

Do not pick up your camcorder by

holding the viewfinder, the LCD panel,

the battery pack, or the microphone.

POWER

OFF

(CHG)

CAMERA

MEMORY

VCR

POWER

OFF

(CHG)

CAMERA

MEMORY

VCR

REW

PLAY

POWER

OFF

(CHG)

CAMERA

MEMORY

VCR

1Open the shutter of the

hood with a lens cap.

For more information

about attaching the

hood with a lens cap.

2Set the POWER switch to

CAMERA while pressing

the small green button.

If the ND1 or ND2

indicator flashes.

3Slide OPEN

back in the B

mark direction

to open the

LCD panel.

OPEN

Viewfinder

When the LCD panel is closed, use the

viewfinder placing your eye against its eyecup.

<<3>>

Installing the microphone

Install the supplied microphone. Be sure to connect the microphone plug to the INPUT1

connector.

(1)Attach the wind screen to the microphone.

(2)Loosen the microphone holder screw and open the cover.

(3)Place the microphone into the holder with the model name (ECM-NV1) facing

upward, close the cover, and tighten the screw.

(4)Connect the plug of the microphone to the INPUT 1 connector.

(5)Set the INPUT LEVEL selector to MIC or MIC ATT. When set to MIC ATT, you

can reduce the volume by about 20 dB. And set the +48 V switch to ON.

(6)Select the channel to be used, using the REC CH SELECT switch. When you

record a sound (signal), which comes from the microphone connected to the

INPUT 1 connector, only on the channel 1, set it to CH1. When you record both

on the channels 1 and 2, set it to CH1•CH2.

When the wind is blowing hard

Set CH1 or CH2 of WIND to ON in the menu settings according to the input (p. 105).

When you unplug the microphone plug

Unplug it while holding the PUSH button down.

123

456

CH1•CH2

REC CH

SELECT

INPUT

LEVEL +48V INPUT

LEVEL +48V

CH1

LINE

MIC

OFF

LINE

MIC

ATT MIC

ATT

MIC

OFF

INPUT1 INPUT2

REC CH

SELECT

INPUT

LEVEL +48V

INPUT2

CH1•CH2

REC CH

SELECT

INPUT

LEVEL +48V INPUT

LEVEL +48V

CH1

LINE

MIC

OFF

LINE

MIC

ATT MIC

ATT

MIC

OFF

INPUT1 INPUT2

REC CH

SELECT

INPUT

LEVEL +48V

INPUT2

Getting Started

Preparing the power supply

Installing the battery pack

Install the battery pack to use your camcorder outdoors.

(1)Lift up the viewfinder.

(2)Insert the battery pack in the direction of the Vmark on the battery pack. Slide

the battery pack until it clicks.

To remove the battery pack

Lift up the viewfinder.

Slide the battery pack out in the direction of the arrow while pressing BATT RELEASE

down.

BATT

RELEASE

Preparing the power supply

Charging the battery pack

Use the battery pack after charging it.

Your camcorder operates only with the “InfoLITHIUM” battery pack (L series).

(1)Open the DC IN jack cover and connect the AC Adaptor supplied with your

camcorder to the DC IN jack with the plug’s vmark facing toward the LCD

panel side.

(2)Connect the power cord to the AC Adaptor.

(3)Connect the power cord to a wall outlet.

(4)Set the POWER switch to OFF (CHG). Charging begins.

The remaining battery time is indicated in minutes on the display window.

When the remaining battery indicator changes to u, normal charge is completed. To

fully charge the battery (full charge), leave the battery pack attached for about one hour

after normal charge is completed until FULL appears on the display window. Fully

charging the battery allows you to use the battery longer than usual.

After charging the battery pack

Disconnect the AC Adaptor from the DC IN jack on your camcorder.

Note on the remaining battery time indicator

The remaining battery time indicator on the LCD screen/display window or in the

viewfinder indicates the recording time using the viewfinder. The indicator may not be

correct, depending on the conditions in which you are recording. When you close the

LCD panel and open it again, it takes about one minute for the correct remaining

battery time to be displayed.

POWER

OFF

(CHG)

CAMERA

MEMORY

VCR

Getting Started

Preparing the power supply

Connecting to a wall outlet

When you use your camcorder for a long time, we recommend that you power it from a

wall outlet using the AC Adaptor.

(1)Open the DC IN jack cover and connect the AC Adaptor to the DC IN jack on

your camcorder with the plug’s vmark facing toward the LCD panel side.

(2)Connect the power cord to the AC Adaptor.

(3)Connect the power cord to a wall outlet.

Precaution

The set is not disconnected from the AC power source (house current) as long as it is

connected to the wall outlet, even if the set itself has been turned off.

Notes

•The power cord must only be changed at an authorized service shop.

•AC Adaptor can supply power even if the battery pack is attached to your camcorder.

•Do not use the AC Adaptor placed in a narrow space, such as between a wall and

furniture.

•The DC IN jack has source priority. This means that the battery pack cannot supply

any power if the power cord is connected to the DC IN jack, even when the power

cord is not plugged into a wall outlet.

Using a car battery

Use the Sony DC Adaptor/Charger (optional).

12,3

Getting Started

Inserting a cassette

(1) Install the power source.

(2) While pressing the small blue button on the EJECT switch, slide it in the

direction of the arrow. After the cassette lid is opened, the cassette

compartment automatically opens.

(3) Push the middle portion of the back of the cassette to insert it.

Insert the cassette in a straight line deeply into the cassette compartment with

the window facing out and the write-protect tab facing upward.

(4) Close the cassette compartment by pressing the PUSH mark on it.

(5) Close the cassette lid until it clicks by pressing the PUSH button on the lid.

To eject a cassette

Follow the procedure above, and take out the cassette in step 3.

Note

The cassette lid will not be closed when you press any part of the lid other than the

PUSH button.

When you use cassettes with cassette memory

Read the instruction about cassette memory to use this function properly.

To prevent accidental erasure

Slide the write-protect tab on the cassette to SAVE.

If the grip strap prevents the cassette lid from opening fully

Adjust the length of the grip strap.

If flashes even if the cassette has been inserted

Press the PUSH button again to close the cover firmly.

23,4 5

PUSH

Write-protect tab

Window

PUSH

40min

REC 00:00:00:01

DVCAM

32K

OPEN

MEMORY

CAMERA

VCR

OFF

(CHG)

POWER

OFF

(CHG)

CAMERA

MEMORY

VCR

LOCK

Camera recording lamps Microphone

— Recording – Basics —

Recording a picture

Your camcorder automatically focuses for you.

(1) Open the shutter of the hood with a lens cap.

(2) Install the power source and insert a cassette. See “Step 2” to “Step 4” (p.11 to

17) for more information.

(3) Set the POWER switch to CAMERA while pressing the small green button.

Your camcorder is set to the standby mode.

(4) Slide OPEN in the direction of the Bmark to open the LCD panel.

The picture now being shot is displayed on the LCD screen, and it disappears

from the viewfinder screen.

(5) Press START/STOP. Your camcorder starts recording. The “REC” indicator

appears. The camera recording lamps located on the front and rear of your

camcorder light up. To stop recording, press START/STOP again.

You can use REC START/STOP located on the handle or front instead of

START/STOP on the rear.

If the ND1 or ND2 indicator flashes on the LCD screen or in the viewfinder

The ND filter is necessary. Set the ND FILTER selector to 1 or 2. However, if you change

the position during recording, the brightness of the picture may change or audio noise

may occur. This is not a malfunction. We recommend that you check the position of the

ND FILTER selector before shooting. See “Using the ND filter” on page 47.

Note

Fasten the grip strap firmly.

REC START/STOP

Handle REC START/STOP

Recording – Basics

Recording a picture

Adjusting the brightness of the LCD screen

To adjust the brightness of the LCD screen, press LCD BRIGHT + or –.

The battery life is longer when the LCD panel is closed. Use the viewfinder instead of

the LCD screen to save the battery power.

On the LCD screen backlight

You can change the brightness of the backlight. Select LCD B.L. in the menu settings

(p. 105).

Even if you do the LCD screen adjustment using the LCD BRIGHT +/– buttons, or

using LCD B.L. and LCD COLOR items in the menu settings

The recorded picture will not be affected.

Recording in a low position

You can record in a low position to get an interesting recording angle. Lift up the

viewfinder or rotate the LCD panel with the screen facing up to record from a low

position. In this case, it is useful to use the REC START/STOP located on the handle or

front of the camcorder.

LCD BRIGHT

To brighten

To darken

REC

START/

STOP

START/

STOP

REC

After recording

(1)Set the POWER switch to OFF (CHG).

(2)Close the LCD panel.

(3)Eject the cassette.

(4)Remove the battery pack.

Adjusting the viewfinder

If you record pictures with the LCD panel closed, check the picture with the viewfinder.

Adjust the viewfinder lens to your eyesight so that the images in the viewfinder come

into sharp focus.

Lift up the viewfinder and move the viewfinder lens adjustment lever.

Even if you adjust the viewfinder screen backlight

The recorded picture will not be affected.

The eyecup

You can attach the eyecup with the large part of it located on both left and right.

Recording a picture

Viewfinder adjustment lever

Andere Handbücher für DSR PD170 - Camcorder - 380 KP

Inhaltsverzeichnis

Andere Sony Camcorder Handbücher

Sony

Sony AV-3600 Bedienungsanleitung

Sony

Sony Digital Handycam DCR-TRV8 Bedienungsanleitung

Sony

Sony HVR-V1P Bedienungsanleitung

Sony

Sony DCR-SX45 Handycam® Bedienungsanleitung

Sony

Sony DCR-HC30 - Handycam Camcorder - 680 KP Bedienungsanleitung

Sony

Sony Handycam Vision CCD-TRV300E Bedienungsanleitung

Sony

Sony DCR-HC85 - Digital Handycam Camcorder Bedienungsanleitung

Sony

Sony CCD-TRV138 - Handycam Camcorder - 320 KP Bedienungsanleitung

Sony

Sony Digital Handycam DCR-PC100E Bedienungsanleitung

Sony

Sony HXC-100 Bedienungsanleitung

Sony

Sony HXR-MC50E Bedienungsanleitung

Sony

Sony DVCAM DSR-PD150 Bedienungsanleitung

Sony

Sony FDR-AX700 Bedienungsanleitung

Sony

Sony CCD-TRV318 Bedienungsanleitung

Sony

Sony XDCAM PDW-850 Bedienungsanleitung

Sony

Sony HVR-Z1J Bedienungsanleitung

Sony

Sony DCR-PC330 Bedienungsanleitung

Sony

Sony VX2000/150 Bedienungsanleitung

Sony

Sony Handycam CCD-FX520 Bedienungsanleitung

Sony

Sony Handycam CCD-FX430 Bedienungsanleitung

Sony

Sony Handycam DCR-TRV940 Bedienungsanleitung

Sony

Sony Handycam DCR-TRV11E Bedienungsanleitung

Sony

Sony CCD-CR1 - Video Camera Recorder 8mm Bedienungsanleitung

Sony

Sony EVI-HD1 Bedienungsanleitung

Beliebte Camcorder Handbücher anderer Marken

Toshiba

Toshiba CAMILEO Z100 Bedienungsanleitung

Panasonic

Panasonic NV-VS40B Bedienungsanleitung

Canon

Canon RC 260 Bedienungsanleitung

Brinno

Brinno TimeLapse TLC200 Bedienungsanleitung

JVC

JVC GR-SXM68AC Kurzanleitung

Panasonic

Panasonic AG-HMC152EN Bedienungsanleitung

MYDLINK

MYDLINK DCS-6100LH Bedienungsanleitung

SECURECOM

SECURECOM V-5014B Bedienungsanleitung

Sharper Image

Sharper Image U-VIDEO Bedienungsanleitung

JVC

JVC AA-V15EG Bedienungsanleitung

Canon

Canon LEGRIA HV40 Bedienungsanleitung

RCA

RCA CC616 Bedienungsanleitung

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung

Panasonic

Panasonic NVM40 Bedienungsanleitung

ATIK Cameras

ATIK Cameras Horizon Bedienungsanleitung

Sharp

Sharp ViewcamZ VL-Z8H Bedienungsanleitung

Philips

Philips M620/21 Bedienungsanleitung

Canon

Canon XF400 Bedienungsanleitung