Sony UMC-S3C Bedienungsanleitung

Digital Video Camera

Technical Manual

Before operating the unit, please read this manual thoroughly

and retain it for future reference.

UMC-S3C

C-372-100-11 (1)

Table of Contents

Location and Functions of Part ............................... 3

Installation ................................................................. 6

Mounting the lens .................................................. 6

Mounting the tripod adapter .................................. 7

Connection ................................................................. 8

Connection to the power supply ............................ 8

Connection to an I/O terminal ............................... 8

Specifications ........................................................... 11

License ...................................................................... 14

About Trademarks

• “Exmor” and are trademarks of Sony

Corporation.

• SD and microSD are trademarks of SD-3C and LLC.

All other company and product names are trademarks or

registered trademarks of the respective companies or their

respective makers.

Location and Functions of Part

aMount

Mount the E mount lens.

bImage sensor

Note

Do not touch directly with your hands.

cLens contacts

Note

Do not touch directly with your hands.

dSD memory card cover

To use the SD memory card slot, insert the SD memory

card by opening the cover.

eSD memory card slot

The SD memory card (sold separately) can be attached.

By attaching the SD memory card, you can record the

video of the camera to the SD memory card.

Insert facing the terminal to the rear side as indicated in the

illustration. Then press down softly until it clicks to attach

firmly.

To remove the card, push the card down till it clicks, then

remove.

This camera only supports SD memory cards of SDXC

standards and SDHC standards.

*SD memory cards which follows all conditions below

- Capacity of more than 64 GB

- To record with SD Speed class 10: , or UHS Speed class higher

than 1: , higher than 100 Mbps, UHS Speed class 3: is required.

Notes

• Please contact the Sony inquiry counter for verified SD

memory cards.

• Make sure to insert it in the dedicated adapter, when

micro SD memory card is used on the camera.

• When you remove the card, ensure that the access light

is turned off. If you remove the card while the light is

turned on or blinking, the data stored in the SD memory

card may be damaged.

POWER

231

Supported memory card Still image Video

SD memory card a–

SDHC memory card a–

SDXC memory card aa*

micro SD memory card a–

micro SDHC memory card a–

micro SDXC memory card aa*

fImage sensor position mark

The mark describes the position on the image sensor.

Use the position of this line to measure the distance from

the camera to objects correctly.

gAccess lamp

Flashes while reading/writing on the SD memory card.

Do not remove the SD memory card or power plug, when

the access lamp is on.

Otherwise, the data in the SD memory card may be

damaged.

hPOWER (power) indicator (green)

Lights up green when the camera is operating normally.

iLens release button

To remove lens, rotate the lens by pressing the button.

When you mount the lens, do not press the button.

jMount index

k12 V !(DC power input) terminal

Connects to DC 12 V power supply.

For details, see Connection to the power supply on page 8.

To turn off the camera, control the camera via the I/O

terminal or multi/micro USB terminal.

lI/O terminal

Can control the external camera.

For details, see Connection to an I/O terminal on page 8.

mHDMI connector (Type D)

Connect a commercial HDMI cable.

nMulti / Micro USB terminal

You can connect devices which support micro USB

standards to this terminal to control the camera from

external devices.

Notes

• Do not wire the cable routed outdoors, when qa, qd is

connected.

• To wire indoors, the cable should be shorter than 30 m

for qa, qd.

• The cable should be shorter than 3 m for qf.

• When connected to qd, qf, it is recommended to secure

the cable to prevent disconnection from the camera due

to its weight or from external force.

Upper side/Bottom side/Rear side

aScrew hole to mount the camera

Use this to fix camera.

Notes

Use screws with a depth of 3.5 mm from the mounting

surface of the camera.

The depth should not be over 4 mm.

Otherwise the screw damages the inside of the camera and

could lead to failure.

bCamera mounting screw holes/Tripod

mounting screw holes

To use a tripod, use these 4 screw holes to securely attach

the tripod adapter.

cRating label

This label shows the name of the device and its electric

rating.

Upper side Bottom side

Rear side

Installation

Warning

• Do not leave the lens facing the sun.

The sunlight enters through the lens and focuses inside

the camera and will lead to a fire accident.

• Attach the lens in the exact way described in this

document. Loose attachment may lead to injury due to

the lens falling off. Check that the attachment is not

loose at least once a year. Perform more frequent checks

depending on the usage.

• Full performance may not be achieved depending on the

installed circumstance or lens. Please contact Sony for

details.

Mounting the lens

Mounting/removing of the lens should be performed after

turning the camera “OFF”.

Remove the body cap from the camera and the lens

rear cap from the lens.

• Perform this operation in a dustless place in a quick

manner to prevent the dust getting into the camera.

• Remove the lens front cap on the front side of the

lens when you shoot.

Align two white dots on the lens and camera, then

engage.

• Face the mount downward to prevent dust from

getting in.

Push the lens to the camera softly, then rotate it in the

direction of the arrow until it clicks.

• Do not insert the lens at a tilted angle.

Notes

• When you mount the lens, do not press the Lens release

button.

• Do not apply any force on the lens.

• Hold securely for both the camera and lens when you

carry the camera with a lens mounted.

• Do not hold the camera holding the lens part that juts out

when zooming or focusing.

• Zoom lens use

Zoom position may be changed depending on the

installed circumstances.

Make sure to secure the zoom ring by applying tape as

necessary.

Recommended tape: 3M Scotch®plastic film tape

Model No. 471 BLA 50 equivalents

To remove the lens

Rotate the lens in the direction of the arrow until it

stops by pressing the Lens release button, then

remove.

Lens front cap

Lens rear cap

Body cap

Apply the tape on the zoom ring full circle to fix.

Zoom ring

Tape

Lens release button

Mount the body cap on the camera and the cap around

the lens.

• Mount the cap after removing the dust.

Notes on lens exchange

If the dust gets into the camera and stuck to the surface of

the image sensor (a part to convert the light to an electrical

signal) upon lens exchange, dust may appear in the image.

Mount/remove the lens at a dustless place in a quick

manner.

Mounting the tripod adapter

Use the mounting screw holes on the upper side/bottom

side of the camera/tripod adapter mounting holes (4 inside)

to mount the supplied tripod adapter.

Notes

• Use the supplied screws (M3×6) (recommended

tightening torque: 0.6 N·m)

• Do not install the camera on a place or equipment that

shudders.

• Install on an even flat place.

Notes on installation

When the tripod screws are used

• Use screws which go over (4) the tripod adapter

mounting side by 4 to 5 mm.

• Make sure it doesn't go over more than 5.5 mm.

When the M3 screws (sold separately) are used

• Use screws which go over (4) the tripod adapter

mounting side by 4 to 5 mm.

• Make sure it doesn't go over more than 5.5 mm.

To mount on the bottom side To mount on the upper side

Tripod adapter mounting side

Tripod screwsM3

4= 4 mm to 5 mm

Connection

Connection to the power supply

Connect the power cable to a 12 V terminal.

• Voltage range of the power supply operation is 9 V to 13.2 V (within the warranty scope of the range of voltage the

camera receives (voltage at receiving end)).

• Use a UL cable (VW-1 style 10368) for wiring.

• Use the power supply equipment with supplying power of more than 22 VA for the camera.

• Use an external power supply plug based on IEC60130-10 (JEITA standard RC-5320A) TYPE4 for 12 V power supply

terminal.

• Recommended cables

Connection to an I/O terminal

Connect to an I/O terminal.

·Use a plug based on the 8PIN mini DIN.

Pin layout

Cable (AWG) #20 #18 #16

The maximum cable length (m) 10 20 30

number

Input/

output

Name Function

1 Input Shutter control terminal Shoot with “Low” input

2 Output External strobe control

terminal

When you use a mechanical shutter, perform “High” output from the point where

the shutter is completely opened to the end of exposure.

3 Input Focus control terminal Perform focus lock of the camera with “Low” input

4 GND GND terminal Connect to “GND”

5 Input Extended terminal Do not connect anything

6 Input Power OFF/ON control

terminal

Switch between OFF and ON with “Low” input (min: 500ms)

7 Input Reboot control terminal Reboot the camera with “Low” input (min: 500ms)

8 GND GND terminal Connect to “GND”

Recommended timing plan

I/O terminal circuit diagram

Focus control

Shutter control

External strobe control

Focus lock starts

≥500ms

≥ 500ms

Shutter completely opened

Exposure start

Approx. 20ms Approx. 4.35ms

1, 3, 6 pin

Inside of the camera

3.1 V

22kΩ

100Ω

GND

3.1 V

1, 3, 6 pin

2 pin

Outside

Inside of the camera Outside

2 pin

Mechanical switch

Open collector

Output equipment

GND GND

GND

3.1 V

22kΩ

1kΩ7 pin

Inside of the camera Outside

7 pin

Mechanical switch

Open collector

Output equipment

GND GND

Inhaltsverzeichnis

Andere Sony Camcorder Handbücher

Sony

Sony Handycam NEX-VG900 Bedienungsanleitung

Sony

Sony FCBEH3150 Bedienungsanleitung

Sony

Sony HANDYCAM HVR-M35U Bedienungsanleitung

Sony

Sony Handycam DCR-HC17E Bedienungsanleitung

Sony

Sony Handycam CCD-TR317 Bedienungsanleitung

Sony

Sony SSC-C354 Bedienungsanleitung

Sony

Sony CCD-TRV112 - Video Camera Recorder 8mm Bedienungsanleitung

Sony

Sony DSR-250 Bedienungsanleitung

Sony

Sony MCC-500MD Bedienungsanleitung

Sony

Sony DCR-IP210E Bedienungsanleitung

Sony

Sony Handycam DCR-SR190E Bedienungsanleitung

Sony

Sony Handycam Vision DCR-TRV890E Bedienungsanleitung

Sony

Sony SSC-DC14 Bedienungsanleitung

Sony

Sony Digital betacam DVW-707 Bedienungsanleitung

Sony

Sony DSR PD170 - Camcorder - 380 KP Bedienungsanleitung

Sony

Sony Digital 8 DCR-TRV120 Bedienungsanleitung

Sony

Sony CCD-SC55 (English and Spanishl) Bedienungsanleitung

Sony

Sony bloggie MHS-CM5 Bedienungsanleitung

Sony

Sony BVP-900 Series Maßzeichnung

Sony

Sony Handycam HDR-CX550 Bedienungsanleitung

Sony

Sony Handycam DCR-HC90 Bedienungsanleitung

Sony

Sony Handycam HDR-HC7 Kurzanleitung

Sony

Sony Handycam DCR-SR200 Benutzerhandbuch

Sony

Sony NXCAM NEX-EA50UH Bedienungsanleitung

Beliebte Camcorder Handbücher anderer Marken

Toshiba

Toshiba CAMILEO Z100 Bedienungsanleitung

Panasonic

Panasonic NV-VS40B Bedienungsanleitung

Canon

Canon RC 260 Bedienungsanleitung

Brinno

Brinno TimeLapse TLC200 Bedienungsanleitung

JVC

JVC GR-SXM68AC Kurzanleitung

Panasonic

Panasonic AG-HMC152EN Bedienungsanleitung

MYDLINK

MYDLINK DCS-6100LH Bedienungsanleitung

SECURECOM

SECURECOM V-5014B Bedienungsanleitung

Sharper Image

Sharper Image U-VIDEO Bedienungsanleitung

JVC

JVC AA-V15EG Bedienungsanleitung

Canon

Canon LEGRIA HV40 Bedienungsanleitung

RCA

RCA CC616 Bedienungsanleitung

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung

Panasonic

Panasonic NVM40 Bedienungsanleitung

ATIK Cameras

ATIK Cameras Horizon Bedienungsanleitung

Sharp

Sharp ViewcamZ VL-Z8H Bedienungsanleitung

Philips

Philips M620/21 Bedienungsanleitung

Canon

Canon XF400 Bedienungsanleitung