Sony SAL16105 - Zoom Lens - 16 mm Bedienungsanleitung

SERVICE NOTE

SPECIFICATIONS

REPAIR PARTS LIST

DISASSEMBLY ADJUSTMENTS

SERVICE MANUAL

Revision History

Sony EMCS Co.

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

SERVICE NOTE

SPECIFICATIONS

REPAIR PARTS LIST

DISASSEMBLY ADJUSTMENTS

Link (Japanese)







Link (English)

Ver. 1.3 2008.05

LENS FOR DSLR CAMERA

2008E0800-1

Published by Kohda TEC9-852-220-14

US Model

Canadian Model

AEP Model

Chinese Model

Japanese Model

SAL16105

(DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

• About the Lens Test Projector and Finished Inspection JIG

Revised-3

Replace the previously issued

SERVICE MANUAL 9-852-220-13

with this Manual.

—2 —

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

SPECIFICATIONS

• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.

• Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused

at infinity.

Equivalent 35mm-format focal length*1(mm)

4-157.5

Lens groups elements

11-15

Angle of view*1

83°-15°

*1The values for equivalent 35mm-format focal length and angle of view are based on Digital Single Lens Reflex Cameras equipped with an APS-

C sized image sensor.

Minimum focus*2(m (feet))

0.4 (1.3)

*Minimum focus is the shortest distance from the image sensor to the subject.

Maximum magnification (X)

0. 3

Minimum f-stop

f/ -36

Filter diameter (mm)

Dimensions (maximum diameter ××

××

×height) (mm (in.))

Approx. 7 × 83 ( 7/8 × 3 3/8)

Mass (g (oz.))

Approx. 470 (16 9/16)

Included items

Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Set of printed documentation

Designs and specifications are subject to change without notice.

WIDE

TELE

1st Lens

(52.148mm)

2nd Lens

(11.957mm)

3rd Lens

(26.798mm)

4th Lens

(36.716mm)

Extra-Low Dispersion Glass Aspheric Lens

1-1

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

1. SERVICE NOTE

1-1. Chemicals

Some chemicals used for servicing are highly volatile.

Their evaporation caused by improper management affects your health and environment, and wastes resources.

Manage the chemicals carefully as follows.

• Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.

• Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.

• Keep containers sealed to avoid natural evaporation when chemicals are not in use.

• Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and

use up it.

1-2. Exterior Parts

Be careful to the following points for exterior parts used in this unit.

• Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts.Avoid using chemicals.

Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.

• Insert the specific screws vertically to the part when installing a exterior part.

Be careful not to tighten screws too much.

1-3. Unleaded Solder

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Be careful to the following points to solder or unsolder.

• Set the soldering iron tip temperature to 350 °C approximately.

If cannot control temperature, solder/unsolder at high temperature for a short time.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

• Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing

unleaded solder and leaded solder will cause detachment phenomenon.

1-2

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

1-4. SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and

bridges.

2. Check the interboard wiring to ensure that no wires are “pinched”or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the

customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their

replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270 °C during repairing.

•Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering or unsoldering.

SAFETY-RELATED COMPONENTWARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH

MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION

Dangerofexplosionif batteryisincorrectlyreplaced.

Replace only with the same or equivalent type.

2-1

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

2. DISASSEMBLY

Cut and remove the part of gilt

which comes off at the point.

(Be careful or some

pieces of gilt may be left inside)

Notches Holes

Universal wrench

J-6082-609-A

Chip-A for

universal wrench:

J-6082-609-1

Chip-B for

universal wrench:

J-6082-609-2

Notches

Chip-A

Chip-B

Chip

Match the universal wrench

to the width of holes or notches. Universal wrench

Holes

A-20

B-110

B-40

G-118

O-20

B-10 G-115

G-116

LOCTITE 460

or the equivalent

SERVICETOOLS

Anti-diffusion agent (A-20): J-6082-611-A

Adhesive bond (B-110): J-6082-617-A

Adhesive bond (B-40): J-6082-614-A

Grease (G-118): J-6082-680-A

Oil (O-20): J-6082-610-A

Adhesive bond (B-10): J-6082-612-A Grease (G-115): J-6082-627-A

Grease (G-116): J-6082-628-A

Adhesive bond (LOCTITE 460)

or the equivalent.

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, dont’press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

UNIVERSALWRENCH

In case of the following notches or holes are located in the lens block, etc during disassembling/

assembling the lens, Use the universal wrench.

How to Use

Attach the chip-A or chip-B to the universal wrench.

For the notches: chip-A

For the holes: chip-B

Match the universal wrench to the holes or notches of the lens block, etc.

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6) 2-2

2-1. DISASSEMBLY

The following flow chart shows the disassembly procedure.

REPAIR PART LIST

DISASSEMBLY

REPAIR PART LIST

DISASSEMBLY

REPAIR PART LIST

DISASSEMBLY

REPAIR PART LIST

DISASSEMBLY

Note:

This lens can disassemble both the

1st lens side and the mount side.

Refer to DISASSEMBLY or flow chart

for disassembly.

2-2-1.

2-2-2.

2-2-3.

2-2-4.

G1+G2

First Lens Holder Block

2nd Lens Barrel Assy

4th Lens Block

3rd Lens Barrel Assy

2-2-1. LENS BLOCK

Lens Mount Block

Zoom Barrel

Inner Barrel Assy

2-2-2.

LENS MOUNT BLOCK

Pinch Clutch Block

Fixed Barrel R Assy

2-2-3. INNER BARREL ASSY2-2-4. FIXED BARREL ASSY

Fixed Barrel Assy

Fixed Barrel

Front Lens Barrel R Assy

Lens Mount

Block

Connection Board

Rear Light

Shield Barrel

Back Adjustment Washer

Zoom Barrel

Zoom Rubber

Ring

Focus Rubber

Ring

Rear Barrel

Cinuber Ring

Focus Brush

Zoom Brush

Ground

Brush

First Lens Holder Block

G1+G2

1st Lens

Stopper Barrel

2nd Lens Barrel Assy

2nd Block

Adjustment Waser

3rd Lens Barrel Assy

4th Lens Block 4th Lens Barrel

Hold Washer

3-4 Interval

Adjustment Washer

Focus Differential Ring

Inner Barrel Assy

Second Lens Holder

Fixed Barrel

Zoom Cam Ring

3-4 Moving Frame Assy

Focus Cam Barrel

Front Lens Barrel R Assy

1st Lens Block

Guide Barrel

First Cam Ring

Pinch Clutch Block

Focus Stopper

Focus Ring

Focus Scale Plate

Zoom Cam

Barrel Holder

Rear Barrel

Assy

Fixed Barrel Assy

AF Coupler

Fixed Barrel R Assy

Mount Shielding O-Ring

Outer

Cover Block

CL-002 Block

Ver. 1.2 2008.02

The changed portions from

Ver. 1.1 are shown in blue.

2-3

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

APERTURE

DIAMETER

ADJUSTMENT

FLANGE BACK

ADJUSTMENT

Universal wrench

J-6082-609-A 1st Lens Stopper

Barrel

1st Lens Stopper

Barrel

Apply the adhesive bond (B-10)

to the position two threads from

First lens holder block.

First Lens

Holder Block

10mm

1st Cam Ring

Decoration Plate

2nd Decoration Plate

2nd Block Adjustment

Washer

2nd Lens Barrel Assy

Chip-A for

universal wrench:

J-6082-609-1

(See Page

2-4.)

Note (Assembling)

Align the Notch with

the Mark A.

G1+G2

First Lens

Holder Block

Mark A

Notch

Note (Assembling)

Align the Mark B with

the Mark A.

Mark A

Mark B

B-10 B-10

Note (Assembling)

Make the lens

upside down.

EXPLODEDVIEW

2-2. DETAILS

2-2-1. LENS BLOCK

Ver. 1.2 2008.02

The changed portions from

Ver. 1.1 are shown in blue.

2-4

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

4th Lens Barrel

Hold Washer

4th Lens Barrel

Hold Washer

4th Lens Block

3-4 Interval

Adjustment

Washer

3rd Lens

Barrel Assy

Tweezers

Note (Assembling)

Align the Large Cutout

with the Notch.

Large

Cutout

Notch

Universal wrench

J-6082-609-A

Chip-A for

universal wrench:

J-6082-609-1

83rd Lens

Barrel Assy

2-2-2.

(See Page

2-5.)

(From Page

2-3.)

PARTIAL BLUR

ADJUSTMENT

Lens made

upside down.

2-5

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

2-2-2. LENS MOUNT BLOCK

EXPLODEDVIEW

Note (Assembling)

Adjust the Ground Brush to the portion

there is No Convex in inner circle of

the Zoom Rubber Ring.

Rear Light

Sheild Barrel

Connection Board

Ground Spring

Lens Mount Block

(See Page

2-8.)

(See Page

2-6.)

HELP02-01

Back Adjustment Washer

Coupler Adjustment Washer AF Coupler

Ground Brush

Zoom Rubber Ring Convex

No Convex Portion

2-2-1.

(From Page

2-4.)

B-40

FLANGE BACK

ADJUSTMENT

FLANGE BACK

ADJUSTMENT

G-118

2-6

SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)

Polyester Tape

(Black) 10mm

(7X13mm)

Ground Brush

Polyester Tape (Black) 10mm

(7X13mm)

Zoom Ring

Reinforcement Plate

Zoom Barrel

Note (Assembling)

Zoom Brush

Polyester Tape

(Black) 10mm

(7X13mm)

Polyester Tape (Black) 10mm

(7X13mm)

Note (Assembling)

Notches

Zoom

Coupling Pins

Note (Assembling)

Align the Notches with

the Zoom Coupling Pins.

(From Page

2-5.)

HELP02-02

ZOOM BRUSH

POSITION

ADJUSTMENT

Taping Position Taping Position

G-118 G-118

Cinuber Ring,

Rear Barrel Assy

(See Page

2-7.)

(See Page

2-8.)

Andere Handbücher für SAL16105 - Zoom Lens - 16 mm

Inhaltsverzeichnis

Andere Sony Kameraobjektiv Handbücher

Sony

Sony SEL2070G Bedienungsanleitung

Sony

Sony SAL18250 - Zoom Lens - 18 mm Bedienungsanleitung

Sony

Sony NEX-3D - alpha; Nex-3 With Sel-16f28 Bedienungsanleitung

Sony

Sony SAL70200G - 70-200mm f/2.8 SSM Lens Installationsanleitung

Sony

Sony VCL-HG0872 Bedienungsanleitung

Sony

Sony SAL-35F14G - 35mm f/1.4 Aspherical G Series Standard Zoom... Bedienungsanleitung

Sony

Sony VCL-HGA07B Bedienungsanleitung

Sony

Sony Alpha FE 28-70mm F3.S-S.6 OSS Bedienungsanleitung

Sony

Sony FE 40mm F2.5 G Bedienungsanleitung

Sony

Sony VCL-HG0758 Bedienungsanleitung

Sony

Sony VCL-HG1758 Bedienungsanleitung

Sony

Sony SEL50F18F Bedienungsanleitung

Sony

Sony MT4037S Bedienungsanleitung

Sony

Sony SAL50F18 - 50mm f/1.8 SAM DT Lens Bedienungsanleitung

Sony

Sony SAL1870 - Zoom Lens - 18 mm Installationsanleitung

Sony

Sony SEL-1855 Bedienungsanleitung

Sony

Sony VCL-HG0730 Bedienungsanleitung

Sony

Sony SAL-24F20Z Bedienungsanleitung

Sony

Sony E 11mm F1.8 Bedienungsanleitung

Sony

Sony VCL-HGD0758 Bedienungsanleitung

Sony

Sony SEL50F18F Bedienungsanleitung

Sony

Sony DT 16-50mm F2.8 SSM Bedienungsanleitung

Sony

Sony SAL1870 - Zoom Lens - 18 mm Bedienungsanleitung

Sony

Sony VCL-M3367 Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung

Nikon

Nikon AF-S Zoom-Nikkor 17-35mm f/2.8D IF-ED Bedienungsanleitung

Samsung

Samsung Samsung 18-55mm Bedienungsanleitung

FujiFilm

FujiFilm XF56mm F1.2 R APD Bedienungsanleitung

FujiFilm

FujiFilm FUJINON XK6x20 SAF Bedienungsanleitung

Nikon

Nikon AF-S DX Zoom-Nikkor 18-55mm f/3.5-5.6G ED II Bedienungsanleitung