Sony CMD-CD5 Bedienungsanleitung

SERVICE MANUAL

$(30RGHO

8.0RGHO

______________________________________________________________________________________________________________

SPECIFICATIONS

Signalling format Dual-Band

Frequency range E-GSM 900 MHz,Tran mit: 880 ~ 915 MHz

Receive: 925 ~ 960 MHz

DCS 1800 MHz , Tran mit: 1710 ~ 1785 MHz

Receive: 1805 ~ 1880 MHz

GSM power cla Cla 4 (2W)

DCS power cla Cla 1 (1W)

SIM chip Pluggable mini SIM card

Di play High re olution full graphic di play

Re olution: 97 x 33 pixel

1 header line for icon

3 line x 16 large character

Channel pacing 200 kHz

Number of channel E-GSM: 174

DCS: 374

Frequency tability Tran mit frequency drift ( ynchronized)

< 0,1 p.p.m

RF output power GSM: 2W

DCS : 1W

Battery life Standby : 50h -180h tandard battery

70h -250h extended battery

Talk time : 2h30 - 6h tandard battery

3h30 - 8h20 extended battery

3257$%/(',*,7$/&(//8/$57(/(3+21(

:,7+$&&(6625,(6



Power requirement 3.8 V (nominal)

Operating temperature -10C to +55C

Acce orie operating temperature ± 0C to +45C

Battery pack charging temperature ± 0C to +40C

Dimen ion 139 mm x 45.5 mm x 26.5 mmñ

Weight 139 g

Volume 120 cmñ

Supplied acce orie Power adapter : QN-2AC1 (AEP)

QN-2AC2 (UK)

QN-2AC3 (Au tralia)

Battery ( td.) QN-CD5BPS

Optional acce orie Battery (extd.) QN-CD5BPE

Cigar Lighter Charger QN-2CC

Travel Charger QN-2TC

Hand free kit QN-CD5HFK

Ea yCom(SoftModem)QN-2EC

PC-Card QN-2PCM

Head et QN-2HS

De ktop Charger QN-CD5DTC

De ign and pecification are ubject to change without prior notice.

Thi appliance conform with EEC Directive 87/308/EEC regarding interference uppre ion.

NOTE

This device contains electrostatic sensitive components. Damage can occur to these components

if the appropriate handling is not adhered to.

Handling precautions:

A working area where Digital Cellular Telephones may be safely handled without undue risk of

damage from electrostatic discharge, must be available.

The area must be equipped as follows:

½All working surfaces must have a dissipative bench mat, safe for use with live equipment,

connected via 1.2MΩresistor to a common ground point.

½A quick release skin contact device with a flexible cord, which has a built in safety resistor of

between 5.2MΩand 1.2MΩshall be used. The flexible cord must be attached to a

dissipative earth point.

½All containers and storage must be of the conductive type.

Batteries:

This device contains an internal battery in addition to the external battery packs. These batteries

are recyclable and should be disposed of in accordance with national legislation. They must not

be incinerated, or disposed of as ordinary rubbish.

TABLE OF CONTENTS

SECTION 1

Specifications ……………………………………………………… (see Cover sheet)

SECTION 2

General Descriptions

2.1 Multi Band ………………………………………………………. 05

2.2 Real Time Clock ……………………………………………….. 05

2.3 Vibra Alert Functionality ……………………………………….. 05

2.4 Battery Safety ……………………………………………………05

2.5 Battery Capacity ….…………………………………………….. 06

2.6 Accessory Interface ..…………………………………………... 06-07

2.7 RF Antenna connector / antenna switch..……………………. 08

2.8 Languages ……………………………………………………….08

SECTION 3

Available Accessories

3.1 Hands free kit QN-CD5 HFK…………………………..09

3.2 Cigar Lighter Charger QN-2 CC………………………………..09

3.3 Travel Charger QN-2 TC………………………………..09

3.4 EasyCom-SoftModemQN-2 EC..……………………………... 09

3.5 PC Card QN-2 PCM……………………………...10

3.6 Head set QN-2 HS………………………………..10

3.7 Desktop Charger QN-CD5 DTC…………………………..10

3.8 Extended Battery QN-CD5 BPE…………………………..10

SECTION 4

Operating Instructions

4.1 Basic Features …………………………………………………..11

4.2 Icon Glossary ………..…………………………………………..12

4.3 Menu Overview ………………………………………………….13

SECTION 5

5.1 Disassembly ……………………………………………………..14-15

5.2 Interface to GSM-Tester ………………………………………..16

SECTION 6

Programming Instructions

6.1 Requirement ..……………………………………………………17

6.2 Hardware set-up ..…..….………………………………………..17

6.3 Software set-up .…………………………………………………17-18

6.4 Display contrast adjustment ..…………………………………..19

SECTION 7

7.1 Block Diagram – Radio Frequency …….…………………….. 20

7.2 Block Diagram – Baseband …………………………………… 21

SECTION 8

Exploded View …..…...…………………….……………………….. 22

SECTION 9

9.1 Spare Parts and Accessories List ……………………………..23

SECTION 2

GENERAL DESCRIPTIONS

2.1 Multi-band :

CMD-CD5 support E-GSM 900 and DCS 1800 multi-band functionality.

Because the usage of multi-band depends on network capabilities, the phone is able to operate as a single band

mobile in GSM 900 as well as in DCS 1800; In addition, it supports the extra functionality required for multi-band

mobile stations: Inter-band/”seamless” hand-over, channel assignment, cell selection and re-selection, all between

both bands within a Public Land Mobile Network.

The manual and automatic PLMN selection in both bands is given.

The user does not need any special action to use the multi-band functionality of the phone.

Users are able to manually roam between PLMN’s operating in GSM 900 and DCS 1800 bands.

The CMD-CD5 is a phase II, GSM 900 class 4, DCS 1800 class 1 mobile phone.

The nominal maximum output power for GSM 900 is 2W, for DCS 1800 1W.

2.2 Real Time Clock (RTC):

The real time clock is integrated into the phone.

When the mobile is switched on the RTC is powered via the CPU.

When the phone is powered down, the RTC is powered from the main battery via it’s own low quiescent current

regulator.

When the main battery is low or removed, a back-up battery keeps the clock alive.

After the main battery has reached a voltage level of 3.5V the RTC keeps the time for 10 days.

After the main battery is removed the RTC keeps the time for 10 min.

2.3 Vibra Functionality

The vibrator is a 1.3V device with a vibrating frequency fixed at 120Hz (±20%).

A general port pin of the CPU controls the switch mode of the vibration motor. It is powered direct from the battery

by an interface control unit. If the mobile is in the phase of switching on or off the vibrator is off at all times.

2.4 Battery Safety

The battery pack contains a safety circuitry. The charging circuitry and the safety circuitry together guarantee a

double fail-safe battery pack. This means that each component can be either short or open and still all the safety

requirements will not be violated.

The safety concept protects against:

Over voltage: The charging is stopped when Battery Voltage (Vbat) reaches (4.24V- 4.3V). The charging resumes

when Vbat falls below (4.11V - 4.23V).

Under voltage: When the cell voltage drops below (1.3V - 1.7V) the cell is disconnected for discharging.

Charging is still possible.

2.5 Battery Capacity:

Standard Battery 1000mAh typical Li-ion QN-CD5BPS

Extended Battery 1450mAh typical Li-ion QN-CD5BPE

The phone can be charged even during making phone calls.

However, the shortest charging time will be reached when the phone is switched off.

As the charging circuit is integrated in the battery pack, the phone cannot be powered up by the charger without the

battery pack being attached.

2.6 Accessory interface

The table explains what kind of pins the phone supplies to the different accessories.

Pins GND

Charge

1/2

ACC_

power

Audio

Out

ACC

Detect

(OUT)

(IN)

AGND

Charger √√

CLC √√

Desktop charger √√

Head set √ √√√√√ √

HFK √ √√√√√ √

PCMCIA √ √ √√ √√

EasyCom √ √ √√ √√

Connector layout

Connector view from base of phone

The connector comprises the following pins:

Detection:

The detection of accessory is done by the charge pin and the detect pin.

Any accessory with an active charge will wake up the phone.

The insertion and removal of the charger (Cigar Lighter Charger, Desktop-Charger, AC-Charger) is detected via

polling. To reduce the power consumption the polling can take up to 5 sec.

The insertion and removal of other accessory is detected via an Interrupt. This detection is only possible when the

phone is powered up.

ID:

The ID pin indicates what kind of accessory is connected.

ACC power:

ACC-power has different functionality with different accessories. ACC-power supplies power to the headset

(min.2.7V and min. 10 mA) or will be used as a signaling pin for the Hands Free Kit.

In the car-kit environment the ext. Vbat indicates that a phone call is accepted/in progress. This information is used

by the car-kit to power up the audio section of the car-kit, mute the car stereo and keep the car-kit powered up

even when the ignition is switched off.

Due to the fact that the ID of the accessory is detected first, the ACC power is not current limited (protected).

RX and TX:

This is the communication interface to the PCMCIA card “QN-2PCM” or the PC-link cable ”QN-2EC”.

Audio In and Audio Out

These pins build the audio interface to the Head-Set and the Hands Free Kit.

Audio IN:

To limit the noise which is coupled on the Mic-line, the Mic amplifier in the Hands Free Kit “QN-CD5HFK” and

Head-set “QN-2HS” have an output 280mVrms into 10kΩ.

Audio OUT:

The single ended output delivers 265mV into a 32Ωload.

2.7 RF Antenna connector / antenna switch

To connect an external antenna for accessory use, the CMD-CD5 contains a stable RF connector with an

integrated mechanical switch. This connector is placed on the PWB. The integrated mechanical switch switches

between the helix antenna and the external RF antenna connection. The switching criterium is mechanical

pressure from the RF accessory connector.

2.8 Languages

The CMD-CD5 supports the following languages:

•Bulgarian •French •Portugese

•Croatian •German •Romanian

•Czech •Greek •Russian

•Danish •Hungarian •Slovakian

•Dutch •Italian •Spanish

•English •Norwegian •Swedish

•Finnish •Polish •Turkish

SECTION 3

ACCESSORIES

3.1 Hands Free Kit

The Hands Free Car Kit QN-CD5HFK is designed to offer superior speech quality and Full Duplex speech

transmission. In Full Duplex operation both parties can speak simultaneously. The Car Kit has a RF connector for

the use of an external antenna to offer a high quality radio link to the base station. It is a one box design for quick

and easy installation.

Specifications:

Input voltage DC 12V-24V, negative ground

Rated output voltage 5.0V

Rated output current 500mA

3.2 Cigar Lighter Charger

The QN-2CC Cigar Lighter Charger is only for use in vehicles equipped with a 12-24 volt negative ground electrical

system. This Charger is intended for charging purposes only and not for making/receiving phone calls in the car.

Charging Time:

Full charging can take up to ~3 hours, but will be longer if the CMD-CD5 is switched on or if the temperature is

outside the 0°C - 45°C operating range.

Specifications:

Input voltage DC 12-24V, negative ground

Rated output voltage 5.0V

Rated output current 500mA

3.3 Travel Charger

The Travel Charger QN-2TC is a small and lightweight device. It has a full Input Voltage Range from 100-260Volts.

Using a standard cable makes the connection to the mains socket.

Specifications:

Input voltage 100 to 260 V

Rated output voltage 5.0V

Rated output current 500mA

3.4 EasyCom (Soft Modem)

The EasyCom QN-2EC Data Cable connects the phone to a PC via a RS 232 cable. It supports SMS and

Phonebook function as well as Full Data/Fax Capability 9.6 Kbps.

This configuration is available for Windows 95/98.

3.5 PCMCIA Card

The functionality of the PC Card QN-2PCM is the same as the Data Cable QN-2EC.

3.6 Headset

The Headset QN-2 HS supports full Handsfree Operation, Auto Answering to incoming calls, as well as with

microphone muting function.

3.7 Desk Top Charger

The desktop charger QN-CD5 DTC can charge either the Standard or Extended battery with the phone attached.

The Desk Top Charger gets its power supply via the Power adapter or the Travel Charger QN-2TC.

Specifications:

Input voltage DC 5V

Rated output voltage 5.0V

Rated output current 500mA

3.8 Extended Battery

Specifications:

Lithium Ion Battery QN-CD5 BPE

Maximum output voltage DC 4.2V

Nominal output voltage DC 3.8V

Capacity 1450mAh

Andere Handbücher für CMD-CD5

Inhaltsverzeichnis

Andere Sony Handy Handbücher

Sony

Sony H4413 Benutzerhandbuch

Sony

Sony Xperia ZL Bedienungsanleitung

Sony

Sony XPERIA micro ST23i Bedienungsanleitung

Sony

Sony Xperia miro Bedienungsanleitung

Sony

Sony Xperia E1 Bedienungsanleitung

Sony

Sony Xperia Z5 Service-Handbuch

Sony

Sony Xperia Z3 Bedienungsanleitung

Sony

Sony Xperia C6902 Bedienungsanleitung

Sony

Sony Xperia M5 Dual E5633 Kurzanleitung

Sony

Sony Xperia TX LT29i Bedienungsanleitung

Sony

Sony Xperia S LT26i Kurzanleitung

Sony

Sony Xperia M dual C2004 Bedienungsanleitung

Sony

Sony Xperia ZL C6502 Bedienungsanleitung

Sony

Sony Xperia E dual Kurzanleitung

Sony

Sony Xperia Z2a Benutzerhandbuch

Sony

Sony Xperia XZ2A Benutzerhandbuch

Sony

Sony Xperia XZS SOV35 Service-Handbuch

Sony

Sony CMD-CD18 Bedienungsanleitung

Sony

Sony G3421 Benutzerhandbuch

Sony

Sony Xperia C C2304 Bedienungsanleitung

Sony

Sony A8i G Service-Handbuch

Sony

Sony XPERIA micro ST23i Bedienungsanleitung

Sony

Sony Xperia L S36h Bedienungsanleitung

Sony

Sony Xperia XA1 Ultra Benutzerhandbuch

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung