Sony CMD-MZ5 Bedienungsanleitung

6(59,&(0$18$/

$(30RGHO

8.0RGHO

______________________________________________________________________________________________________________

SPECIFICATIONS

Signalling format Dual-Band

Frequency range E-GSM 900 MHz, Transmit: 880 ~ 915 MHz

Receive: 925 ~ 960 MHz

DCS 1800 MHz, Transmit: 1710 ~ 1785 MHz

Receive: 1805 ~ 1880 MHz

GSM power class Class 4 (2W)

DCS power class Class 1 (1W)

SIM chip Pluggable mini SIM card

Display High resolution full graphics display

Resolution: 96 x 72 pixels

Graphic Icons

5 lines x 12 (normal font numeric) charactors

Channel spacing 200 kHz

Number of channels E-GSM: 174

DCS : 374

Frequency stability Transmit frequency drift (synchronized)

<±0,1 p.p.m

RF output power GSM: 2W

DCS : 1W

Battery life Standby : 30h - 130h

Talk time : 1h30 - 3h40

3257$%/(',*,7$/&(//8/$57(/(3+21(

:,7+$&&(6625,(6

Power requirements 4.0 V (nominal)

Operating temperature -10°C to +55°C

Accessories operating temperature ±0°C to +45°C

Battery pack charging temperature ±0°C to +40°C

Dimensions 90 x 50 x 30 mm

Weight 110 g (with Battery)

Supplied accessories AC Adapter QN-2TC

AC Cable Europe

Battery Pack A-3627-234-A

Desktop Charger 1-476-508-11

Headphones 1-542-459-11

Remote with Microphone 1-476-509-11

Memory Stick A-7094-682-A

Carry Bag 3-230-059-01

Optical Audio Cable 1-757-888-11

Analog Audio Cable 1-823-050-11

Optional accessories Cigar Lighter Charger QN-2CC

Handsfree kit QN-MZ5HFK

EasyCom (SoftModem) QN-2EC

PC-Card QN-2PCM

Travel Charger QN-2TC

Design and specifications are subject to change without notice.

NOTE

This device contains electrostatically sensitive components. Damage can occur to these components

if the appropriate handling is not adhered to.

ESD Handling precautions:

A working area in which Digital Cellular Telephones may be safely handled without undue risk of

damage from electrostatic discharge must be available.

The area must be equipped as follows:

½All working surfaces must have a dissipative bench mat, safe for use with live equipment,

connected via 1.2MΩresistor to a common ground point.

½A quick release skin contact device with a flexible cord, which has a built-in safety resistor of

a range between 5.2KΩand 1.2MΩshall be used. The flexible cord must be attached to a

dissipative earth point.

½All containers and storage must be of the conductive type.

Batteries:

This device contains an internal battery in addition to the external battery pack. These batteries

are recyclable and should be disposed of in accordance with national legislation. They must not

be incinerated, or disposed of as ordinary rubbish.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Discard used batteries according to the

manufacturer’s instructions.

ADVARSEL

Eksplosjonsfare ved feilaktig skifte av batteri.

Benytt samme batteritype eller en tilsvarende type

anbefalt av apparatfabrikanten.

Brukte batterier kasseres i henhold til fabrikantens

instruksjoner.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en likvärdig typ som

rekommenderas av apparattillverkaren.

Kassera använt batteri enligt gällande föreskrifter.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti

asennettu. Vaihda paristo ainoastaan laitevalmistajan

suosittelemaan tyyppiin. Hävitä käytetty paristo

valmistajan ohjeiden mukaisesti.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat

og type.

Levér det brugte batteri tilbage til leverandøren.

TABLE OF CONTENTS

SECTION 1

Specifications ……………………………………………………….(see Cover sheet)

SECTION 2

General Descriptions

2.1 Multi Band …………………………………………………….………… 06

2.2 Real Time Clock (RTC)…………………...……………...……………. 06

2.3 Vibra Alert Functionality ……………………………………..…………06

2.4 Battery Safety …………………………………………………………...06

2.5 Battery Charging ……..……………………………….………………...07

2.6 Accessory Interface …………………………………….………………07

2.7 RF Antenna connector / antenna switch ….……...…………………. 08

2.8 Languages ..…………………………………………………….……….08

2.9 Memory stick ..………………………………………………….………. 08

SECTION 3

Available Accessories

3.1 Hands free kit QN-MZ5 HFK……………….…………… 09

3.2 Ciger Lighter Charger QN-2 CC ……………………..………….. 09

3.3 AC Adapter QN-2 TC …………….……………………09

3.4 EasyCom (SoftModem) QN-2 EC …………………….…………... 09

3.5 PCMCIA Card QN-2 PCM ………………..……..……….09

3.6 Desktop Charger (not for sale by itself) ……………………..………. 10

3.7 Standard Battery QN-MZ5 (not for sale by itself) …..……. 10

3.8 Magic Gate Memory Stick ………………...……………....….………. 10

3.9 Headphones (not for sale by itself) ………………...…….………….. 10

3.10 Remote with Microphone (not for sale by itself) ………….……….. 10

3.11 Optical Cable (not for sale by itself) ……………….……….………. 10

3.12 Carry Bag (not for sale by itself) ……………………..…….……….. 10

3.13 Analog Audio Cable (not for sale by itself) …………..…….……….10

SECTION 4

Operating Instructions

4.1 Parts and Controls ……………………………………………..……….11

4.2 Basic Features ……………………..…………………...……..………..12-13

4.3 Icon Glossary………………………………………..…………………...14

4.4 Menu Overview…………………………….…….….………….………. 15-16

SECTION 5

Disassembling / Testing

5.1 Disassembly ..…………………………………………………………... 17-19

5.2 Interface to GSM-Tester ..…...……………………….……………….. 20-21

5.3 Jigs & Tools .………………………………………..…………………...21

SECTION 6

Programming Instructions

6.1 Requirement …….……………………………………...……………… 22

6.2 Hardware set-up …..…………………………………...……………… 22

6.3 Software set-up …………………………………………….………….. 22

6.3.1 Download Software to Mobile …...…….………………..……….. 23

6.3.2 Save Personal Data In Mobile…………..…….……...………….. 23

SECTION 7

Diagrams

7.1 RF Block

7.1.1 Block Diagram …...…….………………………………....……….. 24

7.1.2 Operational Description…………...……..…….……...………….. 25-26

7.2 Base Band Block

7.2.1 Block Diagram (1/2) ..….………………………………....……….. 27

7.2.2 Block Diagram (2/2)…………...……..…….…….…….………….. 28

7.2.3 Operational Description…………...……..…….……...………….. 29

7.3 Memory Stick Block ………....………………………...………………. 30

7.3.1 Block Diagram (1/2) ..….………………………………....……….. 30

7.3.2 Block Diagram (2/2)…………...……..…….…….…….………….. 31

7.3.3 Operational Description…………...……..…….……...………….. 32

SECTION 8

Spare Parts and Accessories List

8.1 Spare Parts …….………………………………………….…………… 33

8.2 Accessories List …….…………………………………….…………… 34

SECTION 2

GENERAL DESCRIPTIONS

2.1 Multi-band :

CMD-MZ5 support E-GSM 900 and DCS 1800 multi-band functionality.

Because the usage of multi-band depends on network capabilities, the phone is able to operate as a single band

mobile in GSM 900 as well as in DCS 1800; In addition, it supports the extra functionality required for multi-band

mobile stations: Inter-band/“seamless” hand-over, channel assignment, cell selection and re-selection, all between

both bands within a Public Land Mobile Network.

The manual and automatic PLMN selection in both bands is given.

The user does not need any special action to use the multi-band functionality of the phone.

Users are able to manually roam between PLMN’s operating in GSM 900 and DCS 1800 bands.

The CMD-MZ5 is a phase II, GSM 900 class 4, DCS 1800 class 1 mobile phone.

The nominal maximum output power for GSM 900 is 2W, for DCS 1800 1W.

2.2 Real Time Clock (RTC)

The real time clock is integrated into phone.

When the mobile is switched on the RTC is powered via the CPP.

When the phone is powered down, the RTC is powered from the main battery via its own low quiescent current

regulator.

When the main battery is low or removed, a back-up battery keeps the clock alive.

2.3 Vibra Alert Functionality

The vibrator is a 1.3V device.

A general port pin of the SC1 controls the switch mode of the vibration motor. It is powered through a regulator by

an interface control unit. If the mobile is in the phase of switching on or off the vibrator is off at all times.

2.4 Battery Safety

The battery pack contains a safety circuitry. The charging circuitry and the safety circuitry together guarantee a

double fail-safe battery pack. This means that each component can be either short or open and still all the safety

requirements will not be violated.

The safety concept protects against:

Over voltage: The charging is stopped when Battery Voltage (Vbat) reaches 4.24V- 4.3V. The charging resumes

when Vbat falls below 4.06V - 4.15V.

Under voltage: When the cell voltage drops below 2.5V - 2.7V the cell is disconnected for discharging.

Charging is still possible.

2.5 Battery Charging

Standard Battery 620mAh typical Li-ion 1-476-508-11

The phone can be charged even during making phone calls.

However, the shortest charging time will be reached when the phone is switched off.

2.6 Accessory Interface

The table explains what kind of pins the phone supplies to the different accessories.

Pins GND

Charge

1/2

ACC

Power

Audio

Out

ACC

Detect

(OUT)

(IN)

Audio

GND

19/22

AC-Adapter

(QN-2TC) √√

CLC

(QN-2CC) √√

Desktop Charger

(1-476-508-11) √√

HFK

(QN-MZ5HFK) √√ √√√√√ √√√

PCMCIA

(QN-2PCM) √√ √√√√

EasyCom

(QN-2EC) √√ √√√√

Connector layout

The Connector comprises the following pins:

Detection:

The detection of accessory is done by the charge pin and the detect pin.

Any accessory with an active charge will wake up the phone, indicating the battery icon but cannot be operated.

The insertion and removal of the charger (Cigar Lighter Charger, Desktop-Charger, AC-Charger) is detected by the

charge voltage.

The insertion and removal of other accessory is detected via an Interrupt. This detection is only possible when the

phone is powered up.

ID:

The ID pin indicates what kind of accessory is connected.

ACC power:

ACC-power has different functionality with different accessories. ACC-power supplies will be used as a signaling

pin for the Hands Free Kit.

In the car-kit environment the ext. Vbat indicates that a phone call is accepted/in progress. This information is used

by the car-kit to power up the audio section of the car-kit, mute the car stereo and keep the car-kit powered up

even when the ignition is switched off.

RX and TX:

This is the communication interface to the PCMCIA card “QN-2PCM” or the PC-link cable “QN-2EC”.

Audio In and Audio Out

These pins build the audio interface to the Head-Set and the Hands Free Kit.

Audio IN:

To limit the noise which is coupled on the Mic-line, the Mic amplifier in the Hands Free Kit “QN-MZ5HFK”.

Audio OUT:

The single ended output delivers 350mV into a 10kW load.

2.7 RF Antenna connector / antenna switch

To connect an external antenna for accessory use, the CMD-MZ5 contains a stable RF connector with an

integrated mechanical switch. This connector is placed on the I/O connector. The integrated mechanical switch

switches between the helix antenna and the external RF antenna connection. The switching criterion is mechanical

pressure from the RF accessory connector.

2.8 Languages

The CMD-MZ5 supports the following languages:

• Dutch • German • Spanish

• English • Italian

• French • Portuguese

2.9 Memory stick

lYou can record sound data onto the memory stick at the bitrate of 132kbps, 105kbps and 66kbps by Optical

input or Analog input.

lReceiving an incoming call is stopped during recording sound (to keep good sound quality).

lYou can playback sound data recording onto the memory stick

lThe Play Settings function allows you to select how to play back such as Bass, AVLS, and Repeat (Shuffle).

lSelecting the next track, the previous track, going forward, backward and stop are available.

lWhen you receive an incoming call during playback, playback is stopped automatically and the Ringer is heard

from the headphones. An incoming call is received with pressing the answering / ending call button on the

remote.

lTo end, keep the answering / ending call button on the remote pressed.

lPlayback sound can be stopped by pressing the answer / ending call button on the remote during playback.

lAlso, to start playback, press the answer / ending call button on the remote.

lWhen WAP is being used, you can not playback sound recorded onto the memory stick.

SECTION 3

AVAILABLE ACCESSORIES

3.1 Hands Free Kit

The Hands Free Car Kit QN-MZ5HFK is designed to offer superior speech quality and Full Duplex speech transmission.

In Full Duplex operation both parties can speak simultaneously. The cradle secures a safe hold of the phone. The Car

Kit has a RF connector for the use of an external antenna to offer a high quality radio link to the base station.

Specifications:

Input voltage DC 12V, negative ground

Rated output voltage 5.0V

Rated output current 500mA

3.2 Cigar Lighter Charger

The QN-2CC Cigar Lighter Charger is an additional charging option or alternative for the standard charger and only for

use in vehicles equipped with a 12 volt negative ground electrical system. This Charger is intended for charging

purposes only and not for making/receiving phone calls in the car.

Charging Time:

Full charging can take up to ~3 hours, but will be longer if the CMD-MZ5 is switched on or if the temperature is outside

the 0°C - 45°C operating range.

Specifications:

Input voltage DC 12V, negative ground

Rated output voltage 5.0V

Rated output current 500mA

3.3 AC Adapter

The Power Adapter QN-2TC is a small and lightweight device. It has a full Input Voltage Range from 110-240Volts.

Using a standard cable makes the connection to the main socket.

Specifications:

Input voltage 110 to 240 V

Rated output voltage 5.0V

Rated output current 500mA

3.4 EasyCom (Soft Modem)

The EasyCom QN-2EC Data Cable connects the phone to a PC via a RS 232 cable. It supports SMS as well as Full

Data/Fax Capability 9.6 Kbps. The phonebook management application bundled on the CD can not be used with CMD-

MZ5.

This configuration is available for Windows 95/98.

3.5 PCMCIA Card

The functionality of the PC Card QN-2PCM is the same as the Data Cable QN-2EC. But it supports both GSM

connections up to 9.6 Kbps and PSTN connections up to 56 Kbps.

For Windows 95, 98, Windows NT, Mac OS.

3.6 Desktop Charger (not for sale by itself)

The desktop charger can charge either the Standard 1-476-508-11 with the phone attached. The Desk Top

Charger gets its power supply via the Power adapter QN-2TC.

Specifications:

Input voltage DC 5V

Rated output voltage 5.0V

Rated output current 500mA

3.7 Standard Battery (not for sale by itself)

Specifications:

Lithium Ion Battery A-3627-234-A (QN-MZ5BPS)

Maximum output voltage DC 4.2V

Nominal output voltage DC 4.0V

Capacity 620mAh

3.8 Magic Gate Memory Stick

3.9 Eearphones (1-542-459-11) (not for sale by itself)

Ø3.5 stereo mini plug

3.10 Remote with Microphone (1-476-509-11) (not for sale by itself)

3.11 Optical Cable (1-757-888-11) (not for sale by itself)

3.12 Carry Bag (3-230-059-01) (not for sale by itself)

3.13 Analog Audio Cable (1-823-050-11) (not for sale by itself)

Andere Handbücher für CMD-MZ5

Inhaltsverzeichnis

Andere Sony Handy Handbücher

Sony

Sony Xperia1 IV Bedienungsanleitung

Sony

Sony PY7-55365J Bedienungsanleitung

Sony

Sony Xperia J ST26i Kurzanleitung

Sony

Sony Xperia Z3+ Benutzerhandbuch

Sony

Sony H3223 Benutzerhandbuch

Sony

Sony Xperia Bedienungsanleitung

Sony

Sony Xperia Z3+ Bedienungsanleitung

Sony

Sony Xperia XA Bedienungsanleitung

Sony

Sony Xperia T3 Bedienungsanleitung

Sony

Sony Xperia T2 Ultra D5303 Bedienungsanleitung

Sony

Sony Xperia V LT25i Kurzanleitung

Sony

Sony Xperia ZL C6502 Bedienungsanleitung

Sony

Sony Xperia E4 E2104 Bedienungsanleitung

Sony

Sony Xperia S LT26i Bedienungsanleitung

Sony

Sony CMD-C1 Bedienungsanleitung

Sony

Sony Xperia X F5121 Bedienungsanleitung

Sony

Sony Xperia Z5 Bedienungsanleitung

Sony

Sony XPeria ST25i Bedienungsanleitung

Sony

Sony Xperia Z3 Bedienungsanleitung

Sony

Sony Xperia 1 V Referenzhandbuch

Sony

Sony E2003 Bedienungsanleitung

Sony

Sony Xperia 1 IV Referenzhandbuch

Sony

Sony Xperia T2 Ultra dual D5322 Kurzanleitung

Sony

Sony CMD-X2000 Bedienungsanleitung

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung