Sony BKMW-E3000 Bedienungsanleitung

NETWORK INTERFACE BOARD

BKMW-E3000

INSTALLATION MANUAL

1st Edition

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

1 (E)

BKMW-E3000

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 2 (E)

Related manuals................................................................................................... 2 (E)

1. Installation

1-1. Installation Notes .................................................................................. 1-1 (E)

1-1-1. Confirmation Before BKMW-E3000 Installation ................ 1-1 (E)

1-1-2. Installation Flow Chart .........................................................1-4 (E)

1-1-3. Components and Connection Cable .................................... 1-5 (E)

1-1-4. Switch Setting and Function of LEDs on DSP-109 Board .. 1-6 (E)

1-1-5. Switch Setting and Function of LEDs on VN-13 Board ...... 1-7 (E)

1-2. Installation Procedures .......................................................................... 1-8 (E)

1-2-1. Rear Side of the VTR ........................................................... 1-8 (E)

1-2-2. Front Side of the VTR ........................................................ 1-15 (E)

1-3. Setting after Installation ......................................................................1-18 (E)

1-3-1. Network Setting ................................................................. 1-18 (E)

1-3-2. Starting e-VTR Manager .................................................... 1-20 (E)

1-4. SNMP .................................................................................................. 1-22 (E)

1-4-1. Configuring SNMP (SNMP Agent Variables) ...................1-24 (E)

1-4-2. Configuring System Management Information

(SNMP MIB-2 Variables) ..................................................1-26 (E)

1-4-3. Configuring Trap Control

(Professional VTR Category Variables) ............................ 1-27 (E)

2 (E)

BKMW-E3000

Purpose of this manual

This manual is an installation manual of Network Interface Board BKMW-E3000.

This manual is intended for system and service engineers, and provides the informa-

tion that is required to install this unit.

Related manuals

Besides this “installation manual”, the following manuals are available for this unit.

If these manuals are required, please contact your local Sony Sales Office/Service

Center.

.Operation Manual (Supplied with this unit.)

This manual is necessary for application and operation (and installation) of this unit.

.Maintenance Manual (In common with the VTR, available on request)

Volume-1 : Service Instruction

Volume-2 : Parts List, Block Diagrams, and Board Layouts

Volume-3 : Schematic Diagrams

These manuals describe the maintenance and service information (service over-

view, adjustments, board layouts, schematic diagrams, detailed parts list, etc.) for

this unit.

.“Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in this unit.

Semiconductors that cannot be searched for on this CD-ROM are listed in the

maintenance manual (volume-2) for the corresponding unit. The maintenance

manual (volume-2) contains a complete list of all semiconductors and their ID

Nos., and thus should be used together with the CD-ROM.

Part number: 9-968-546-XX

Manual Structure

1-1 (E)

BKMW-E3000

Section 1

Installation

1-1. Installation Notes

1-1-1. Confirmation Before BKMW-E3000 Installation

BKMW-E3000 has the following features mainly:

.MXF D10 file receive/transmit (The receive function is applicable only for recorder.)

.Proxy AV file transmit

.Network service with Web server

.Network service with Windows application

.FTP/HTTP transmit by e-VTR control panel operation

.e-monitor

.Automatic get of network setting information such as IP address, and so on

.Network management using host names (DNS client service)

.Automatic file creation by reading data of the tape or memory label

.User registration

.Backup for setup menu settings

.SNMP

.Links to external servers using meta data

.Automatic file system data management through on external server ... etc.

However, of the VTRs to install the BKMW-E3000, some VTRs having early serial numbers have a

limitation by variations in designs of the EPR-1 boards.

The limitation is one of the following cases:

.The VTR cannot be equipped with the BKMW-E3000.

.MXF D10 file receive/transmit function is available, instead of unavailable SDTI-CP input/output

function of the VTR.

.SDTI-CP input/output function is available, instead of unavailable MXF D10 file receive/transmit

function of the BKMW-E3000.

Before installing the BKMW-E3000, please read thoroughly the following instructions.

1-2 (E) BKMW-E3000

EPR-1 board number suffix and installing pattern

1. Check the serial number of the VTR.

2. Check the part-number suffix of the EPR-1 board by using “Table-1: EPR-1 board number suffix and

serial number”or checking the EPR-1 board directly.

Table-1: EPR-1 board number suffix and serial number

EPR-1 board number suffix

Model -12 -13 -14 and later

MSW-2000 ——10001 -

MSW-A2000P 41001 - 42080 42081 - 42212 45001 -

MSW-A2000 11001 - 11030 —15001 -

MSW-M2000P 40001 - 40975 40976 - 41472 45001 -

MSW-M2000 10001 - 10460 10461 - 10655 15001 -

MSW-M2100P 40001 - 40495 40496 - 41052 45001 -

MSW-M2100 10001 - 10230 10231 - 10345 15001 -

In case of earlier serial number than the above number of suffix -12, the VTR cannot be equipped with

the BKMW-E3000.

3. Check the installing pattern.

In case the EPR-1 board number suffix is -14 and later:

All functions can be used.

In case the EPR-1 board number suffix is -12 or -13:

Select either of the MXF D10 file receive/transmit function or SDTI-CP input/output function.

Table-2: Installing pattern check

.MXF D10 file receive/transmit function:

Receives and transmits the video, audio, or metadata recorded on the tape as MXF D10 file.

.SDTI-CP input/output function:

Receives and transmits the video, audio, or metadata recorded on the tape using SDTI-CP.

Depending on the installing pattern [A], [B] or [C], some installing procedures described in “1-2-1.

Rear Side of the VTR”are different. Attach the BKMW-E3000 correctly as directed in the procedures.

EPR-1 board

part number

Suffix -14 or later

Suffix -12 or -13

Function to select

Not necessary

(All functions can be used.)

Selects MXF D10 file receive/transmit function

Selects SDTI-CP input/output function

Installing pattern

Pattern [A]

Pattern [B]

Pattern [C]

1-3 (E)

BKMW-E3000

Confirming Version

1. Check the following software versions using the maintenance mode M30 of the VTR:

SY ROM Ver. ; V7.10 or higher

SV ROM Ver. ; V6.00 or higher

If the version is lower than the above, upgrade the software of the VTR.

Please contact your local Sony Sales Office/Service Center.

VTR Maintenance Mode

For the detailed information for each menu of the maintenance mode, refer to Section 3 of the mainte-

nance manual volume-1 of the VTR.

.Activating the maintenance mode:

Press S1500 (A-1) on the SS-89 board of the VTR.

.Entering a mode (menu):

Press the F5 (SET) button once under the asterisk cursor (*) is aligned to the desired mode (menu) with

the menu displayed on the video monitor.

The *mark is sifted by turning the MULTI CONTROL knob of the VTR.

.Existing a mode (menu):

Press the F6 (EXIT) button of the VTR several times to exit the mode (menu).

1-4 (E) BKMW-E3000

Modify the front panel.

Attach the SW-1106 board.

Attach the harness (HP-SW).

Attach the front panel (E).

1-3. Setting after Installation

Pattern [A] Pattern [B]

Pattern [C]

Pattern [A] and [B]

Attach

the IF-886

board.

Attach the IF-886

board after removing

the DIF-109 board.

Set the DIP switch

S101-4 of the VN-13

board assembly to “ON”.

Attaching to

the EPR-1

board

1Flow chart of the rear side of the VTR (Refer to Section 1-2-1)

2Flow chart of the front side of the VTR

(Refer to Section 1-2-2)

Attaching

ETHERNET

panel

Attach the IF-885 board.

Connect the connection cable

and harness (LED).

Attach the harness guard assembly.

Pattern [C]

Attach the ferrite clamp.

Attach the VN-13 board assembly.

Connect the connection code and harness (LED).

Connect the harness (EPR-VN).

Attach the ETHERNET panel.

(In hte case of the player ; Attach the blank sheet.)

Attaching the

VN-13 board

assembly

1-1-2. Installation Flow Chart

1-5 (E)

BKMW-E3000

12345

678

!- !=

1-1-3. Components and Connection Cable

Components

No. Name Remarks Section to be referred

1IF-886 board Not required in the case of installing pattern [C]. 1-2-1. Rear Side of the VTR

2IF-885 board

3ETHERNET*panel

4Blank sheet Not required in the case of the recorder.

5Connection cord

6Harness (LED)

7Harness guard assembly

8Ferrite clamp

9VN-13 board assembly

!/ Harness (EPR-VN) Not required in the case of installing pattern [C].

—Hexagonal support (4 pcs) For attaching 1

—Screw B3 x4 Not required in the case of installing patterns [B] and [C].

(10 pcs, 2 of them for spare)

—Screw BVTT3 x6 (8 pcs) For attaching 2and 3

!- Front panel (E) 1-2-2. Front Side of the VTR

!= SW-1106 board

![ Harness (HP-SW)

—CD-ROM (Operation manual and application software)

*: Ethernet is a registered trademark of Xerox Corporation.

Connection cable

UTP cable (Category 5e and higher)

A category 5 cable can only be used for 100BASE-TX communication.

1-6 (E) BKMW-E3000

1-1-4. Switch Setting and Function of LEDs on DSP-109 Board

DSP-109 Board (Side A)

Switches

Never change the setting of switches on “Factory use”.

Ref No. Bit Name Description Factory setting

S11 1 —Factory use OFF

2—Factory use ON

LEDs

LED No. Name Color Description Normal state

D1 —Yellow Lights while data is transmitted to Proxy AV file. —

D2 —Green Lights when the DSP (IC2/DSP-109 board) is not OFF

operating normally.

D3 —Red Blinks while data is transmitted to Proxy AV file. —

D4 —Green Blinks when the FPGA (IC1/DSP-109 board) is Blinks

operating normally.

D5 —Yellow Factory use —

D6 —Green Factory use —

D7 —Red Factory use —

D8 —Green Factory use —

D101 —Green Factory use OFF

S11

D101

D8 D7

D6 D5

D4 D3

D2 D1

H12345

Andere Handbücher für BKMW-E3000

Inhaltsverzeichnis

Andere Sony Computerhardware Handbücher

Sony

Sony PCWA-C150S - Wireless Lan Pc Card Bedienungsanleitung

Sony

Sony MPE-200 Bedienungsanleitung

Sony

Sony HKSR-5804 Bedienungsanleitung

Sony

Sony PCWA-C700 - Wireless Lan Dual Pc Card Datenblatt

Sony

Sony UPA-D3 Bedienungsanleitung

Sony

Sony MVS-8000A-C Bedienungsanleitung

Sony

Sony SDP-EP90ES Bedienungsanleitung

Sony

Sony HFBK-HD1 Bedienungsanleitung

Sony

Sony MPE-200 Bedienungsanleitung

Sony

Sony DVBK-2000 Bedienungsanleitung

Sony

Sony DPS-V55 Bedienungsanleitung

Sony

Sony BPU4800 Bedienungsanleitung

Sony

Sony PCM-F1 Bedienungsanleitung

Sony

Sony VAIO PCWA-C800S Merkblatt

Sony

Sony BPU-4500A Bedienungsanleitung

Sony

Sony INT-W200 Bedienungsanleitung

Sony

Sony PCWA-C150S - Wireless Lan Pc Card Merkblatt

Sony

Sony DEP-100 Bedienungsanleitung

Sony

Sony DSBK-1801 Bedienungsanleitung

Sony

Sony PCWA-C800S Read This First Kurzanleitung

Sony

Sony DPS-V55M Bedienungsanleitung

Sony

Sony SRP-F700 Bedienungsanleitung

Sony

Sony BKPF-292 Bedienungsanleitung

Sony

Sony HR-GP5 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung