Sony SPP-A400 - Cordless Telephone With Answering... Bedienungsanleitung

3-860-454-22 (1)

Operating Instructions

Mode d’emploi

SPP-A400

Cordless

Telephone

with Answering System

2EN

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to

qualified personnel only.

INDUSTRY CANADA NOTICE

NOTICE: The Industry Canada label

identifies certified equipment. This

certification means that the equipment

meets certain telecommunications

network protective, operational and

safety requirements as prescribed in the

appropriate Terminal Equipment

Technical Requirements document(s).

The Department does not guarantee the

equipment will operate to the user’s

satisfaction.

Before installing this equipment, users

should ensure that it is permissible to be

connected to the facilities of the local

telecommunications company. The

equipment must also be installed using

an acceptable method of connection.

The customer should be aware that

compliance with the above conditions

may not prevent degradation of service

in some situations.

Repairs to certified equipment should be

coordinated by a representative

designated by the supplier. Any repairs

or alterations made by the user to this

equipment, or equipment malfunctions

may give the telecommunications

company cause to request the user to

disconnect the equipment.

Users should ensure for their own

protection that the electrical ground

connections of the power utility,

telephone lines and internal metallic

water pipe system, if present, are

connected together. This precaution may

be particularly important in rural areas.

Caution: Users should not attempt to

make such connections themselves, but

should contact the appropriate electric

inspection authority, or electrician, as

appropriate.

NOTICE: The Ringer Equivalence

Number (REN) assigned to each

terminal device provides an indication

of the maximum number of terminal

allowed to be connected to a telephone

interface. The termination on an

interface may consist of any

combination of devices subject only to

the requirement that the sum of the

Ringer Equivalence Number of all the

devices does not exceed 5.

IMPORTANT INSTRUCTION TO

USERS

Your model (SPP-A400) has been

approved by the Industry Canada.

Note

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must

accept any interference, including

interference that may cause undesired

operation of the device.

Privacy of communications may not be

ensured when using this telephone.

DIGITAL SECURITY CODE

Your SPP-A400 has been assigned a

permanent and unique digital security

code out of possible 4,096 codes.

3EN

Table of contents

Getting Started

4 Read this first

5 Step 1: Checking the package

contents

6Step 2: Setting up the base unit

9Step 3: Preparing the battery

pack

Basics

11 Making calls

12 On-hook dialing

12 Redialing

13 Receiving calls

Telephone Features

14 Speed dialing

14 Storing phone numbers

15 Making calls with speed

dialing

16 Paging

Answering Machine

Features

17 Preparing the answering machine

17 Setting the day and time

18 Recording the greeting

19 Turning on the answering

function

21 Playing back messages

22 Screening incoming calls

23 Recording a memo

24 Operating from an outside phone

24 Setting the security code

25 Picking up new messages

Additional Information

26 Resetting the digital security code

27 Mounting the base unit on a wall

29 Notes on power sources/

Maintenance

30 Troubleshooting

33 Specifications

34 Index

Getting Started

4EN

That’s it!

Handset

Getting Started

Base unit

About the digital security code

This cordless telephone uses a digital security code to provide protection against unintentional

access to your base unit.

This security code blocks other cordless handsets to make calls through your base unit.

A random security code will be assigned automatically between your base unit and handset when

you charge the battery pack for the first time.

If you want to reset the security code manually, see page 26.

Read this first

Before you use your phone, you must set it up. Here’s a quick way to

set up your phone: Steps 1, 2, and 3.

Step 2 (pages 6 to 8)

Next, you need to do three things to set

up the base unit, including finding the

best location for the base unit.

Step 3 (pages 9 to 10)

Finally, you need to insert the battery

pack into the handset and charge it for

more than 12 hours.

First, unpack the phone and the supplied

accessories.

Step 1 (page 5)

Getting Started

5EN

Getting Started

Telephone line cord

Handset

AC power adaptor

(AC-T46 or AC-T123)

Wall bracket/stand for base

unit

Base unit

Rechargeable battery

pack (BP-T16)

Directories (2)

Step 1

Checking the package contents

Make sure you have received the following items in the package.

If anything is missing, contact your local Sony dealer.

Getting Started

6EN

Step 2

Away from television

sets and other

electronic equipment

Away from a microwave

oven

Away from excessive

moisture, extremely low

temperatures, dust,

mechanical vibration, or

shock

Away from a personal

computer

Away from another

cordless telephone

Near a central location

and on a level surface

Away from heat sources, such as radiators,

airducts, and sunlight

Away from noise sources such as a window

by a street with heavy traffic

CAUTION

The cordless telephone operates at a frequency that may cause interference to nearby TVs and VCRs;

the base unit should not be placed near or on the top of a TV or VCR; and, if interference is

experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or

eliminate the interference.

Setting up the base unit

Do the following steps:

• Choose the best location

• Connect the base unit

• Choose the dialing mode

Choose the best location

Where you place the base unit affects the reception quality of the

handset.

Getting Started

7EN

Getting Started

continued

1Attach the wall bracket on the

bottom of the base unit as

illustrated to use it as a stand.

2Connect the telephone line cord

to the LINE jack and to a

telephone outlet.

3Connect the AC power adaptor

to the DC IN 9V jack and to an

AC outlet.

“P” flashes in the message

counter.

4Fully extend the antenna.

Make sure it points toward the

ceiling.

Hook the cord.

To DC IN 9V

To LINE

AC power adaptor

(supplied)

Telephone line cord

(supplied)

To AC outlet

To telephone outlet

Connect the base unit

If you want to hang the base unit on the wall, see page 27.

Message counter

Align the ¢

marks.

Getting Started

8EN

Polarity of the plug

Step 2: Setting up the base unit (continued)

DIAL MODE switch

Notes

• Use only the supplied AC power adaptor.

Do not use any other AC power adaptor.

• Connect the AC power adaptor to a continuous power

supply.

• Place the base unit close to the AC outlet so that you

can unplug the AC power adaptor easily.

Tips

• If your telephone outlet isn’t modular, contact your

telephone service company for assistance.

• To remove the wall bracket, press the upper tab.

Choose the dialing mode

For the telephone to work properly, select an appropriate dialing mode

(tone or pulse).

Depending on your dialing system, set the DIAL MODE switch as

follows:

If your dialing system is Set the switch to

Tone T

Pulse P

If you aren't sure of your dialing system

Make a trial call with the DIAL MODE switch set to T.

If the call connects, leave the switch as is; otherwise, set to P.

Modular

Getting Started

9EN

Getting Started

Preparing the battery pack

Charge the battery pack for more than 12 hours before you start using

your phone.

1Slide open the battery

compartment lid of the handset.

2Connect the battery connector

with correct polarity (black and

red cords).

3Hook the cords and insert the

battery pack. Then close the lid.

4Place the handset on the base

unit.

You can place either side facing

up.

The CHARGE/IN USE lamp

lights up when the handset is

properly seated on the charge

terminals of the base unit.

Charge the battery pack for

more than 12 hours so that the

battery is fully charged. The

CHARGE/IN USE lamp

remains lit even after charging

is completed.

continued

Step 3

Red Black

CHARGE/

IN USE lamp

Hook

Getting Started

10EN

Battery duration

A fully charged battery pack lasts for about:

• 6 hours when you use the handset continuously

• 14 days when the handset is in standby mode.

Notes

• The battery pack will gradually discharge over a long period of time, even if

not in use.

• The battery works best when charged after several calls.

• If you leave the battery pack in the handset without charging it, the battery

pack will be completely discharged.

When completely discharged, the speed dial numbers will be erased. If this

happens, charge the battery for more than 12 hours, and then reprogram the

speed dial numbers (see page 14).

It may require several times of charging to recover to its full capacity.

When to purchase a new battery pack

If the battery lasts only a few minutes even after 12 hours of charging,

the usable life of the battery has expired and needs replacement.

Contact your local Sony authorized dealer or service center, and ask

for Sony BP-T16 rechargeable battery pack.

Note

If you replace the battery, the speed dial numbers will be erased.

After you insert the new battery, charge it for more than 12 hours, and then

reprogram the speed dial numbers (see page 14).

Step 3: Preparing the battery pack (continued)

Andere Handbücher für SPP-A400 - Cordless Telephone With Answering...

Inhaltsverzeichnis

Sprachen:

Andere Sony Schnurloses Telefon Handbücher

Sony

Sony SPP-M920 Primary Bedienungsanleitung

Sony

Sony SPP-111 - Cordless Phone Page Bedienungsanleitung

Sony

Sony SPP-933 - 900mhz Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-ID970 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-SS961 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-N1000 Bedienungsanleitung

Sony

Sony SPP-ID975 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-D900 - 900 Mhz Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-935 - 900 Mhz Cordless Phone Bedienungsanleitung

Sony

Sony SPP-1000 Primary Bedienungsanleitung

Sony

Sony SPP-SS964 Bedienungsanleitung

Sony

Sony SPP-AQ25 Primary Bedienungsanleitung

Sony

Sony SPP-AQ500 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A941 - Cordless Telephone With Answering... Bedienungsanleitung

Sony

Sony SPP-N1025 - Cordless Telephone Bedienungsanleitung

Sony

Sony ClearScan25 SPP-AQ600 Bedienungsanleitung

Sony

Sony SPP-N1001 Bedienungsanleitung

Sony

Sony SPP-935 - 900 Mhz Cordless Phone Bedienungsanleitung

Sony

Sony SPP-A968 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A940 - 900 Mhz Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-A250 Primary Bedienungsanleitung

Sony

Sony SPP-ID970 - Cordless Telephone Bedienungsanleitung

Sony

Sony SPP-S9101 - Cordless Telephone Kurzanleitung

Sony

Sony SPP-ID200 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung