Sony Reader PRS-T2 Bedienungsanleitung

SERVICE MANUAL

Sony Corporation

Published by Sony Techno Create Corporation

PRS-T2

SPECIFICATIONS

DIGITAL BOOK READER

9-893-536-01

2012H33-1

US Model

Canadian Model

AEP Model

UK Model

Australian Model

Ver. 1.0 2012.08

Note:

Be sure to keep your PC used for service and

checking of this unit always updated with the

latest version of your anti-virus software.

In case a virus affected unit was found during

service, contact your Service Headquarters.

Model name

PRS-T2

Power source

Built-in rechargeable battery: 3.7 V DC, 1000mAh

USB powered from a computer or the optional AC Adapter

PRSA-AC10/PRSA-AC1A (sold separately) via the supplied

USB cable.

Battery life (continuous page turn)

Maximum Battery: Approximately 30,000 continuous page

turns when reading only.*

* Measured using a text based content in ePub format and a

fully charged battery, consecutive page-turns at

approximately one second per page under the

recommended operating temperature. Actual battery life

may vary based on usage patterns and individual device.

Charging time

Computer-based charging: Approximately 2.5 hours

AC Adapter PRSA-AC10/PRSA-AC1A(sold separately)-based

charging: Approximately 2 hours

Internal memory capacity (for data storage)

Approximately 1.3 GB after initial setting.

Depending on size of pre-loaded excerpts, available memory

capacity may vary.

Operating/Charging temperature

5°C to 35°C (41°F to 95°F)

Dimensions (w/h/d)

Approximately 110 × 173 × 9.1 mm (4 3/8 × 6 7/8 × 3/8

inches)

Mass

Approximately 164 g (5.8 oz.)

Display

152.4 mm (6 inch) diagonal electrophoretic display

600 × 800 pixels, 16-level grayscale

Wi-Fi

Wireless standards: IEEE 802.11b/g/n compliant

Wireless security: WEP (Open System), WEP (Shared Key),

WPA-PSK (TKIP), WPA-PSK (AES), WPA2-PSK (TKIP), WPA2-PSK

(AES)

Expansion slots

microSD card slot

See Details for supported card types and precautions.

Supplied items

USB cable × 1

Stylus × 1

Quick Start Guide

Supported File Types

The following les can be managed on the Reader software

and transferred to the Reader device.

However, depending on the le size and format, it may not

be possible to view/display/play some data.

Books

EPUB les (.epub)

EPUB (OPS version 2.0) supported.

PDF les (.pdf)

Support is based on the PDF 1.6 specication.

Text les (.txt)

FB2 les (.fb2)

Pictures

JPEG les (.jpg, .jpeg)

GIF les (.gif)

PNG les (.png)

BMP les (.bmp)

Note

If the size of a picture that you transferred with the Reader

software is too large, a thumbnail may not be created on

the Reader and the picture may not be displayed in the

[Pictures] content list. In this case, delete the picture via the

Reader software.

For an animated GIF le, only the rst frame will be shown.

System Requirements

The Reader software will work with the following

operating systems.

Operating System Details

Microsoft Windows

7 (32/64-bit)

Windows 7 Starter

Windows 7 Home Basic

Windows 7 Home Premium

Windows 7 Professional

Windows 7 Ultimate

Operating System Details

Microsoft Windows

Vista (32/64-bit)

Windows Vista Home Basic with

Service Pack 2 or later

Windows Vista Home Premium with

Service Pack 2 or later

Windows Vista Business with Service

Pack 2 or later

Windows Vista Ultimate with Service

Pack 2 or later

Microsoft Windows

XP (32-bit only)

Windows XP Home Edition with

Service Pack 3 or later

Windows XP Professional with Service

Pack 3 or later

Windows XP Media Center Edition

2004 & 2005 with Service Pack 3 or

later

Mac OS X 10.7 (64-

bit only)

Mac OS X version 10.7 or later

Mac OS X 10.6

(32/64-bit)

Mac OS X version 10.6.6

Mac OS X 10.5 (32-

bit only)

Mac OS X version 10.5.8

The Reader software also requires at minimum the

following computing environment.

Requirement Details

CPU 1 GHz Intel processor

RAM 512 MB

Free space on hard

disc

250 MB or more*

Screen 1,024 x 768 display resolution with

24-bit color

Network Broadband internet connection

* Depending on the content amount, more space may be

required.

Note

The Reader software is not supported with the following:

An operating system other than those listed above

A personally built computer or operating system

A multi-boot environment

A multi-monitor environment

PRS-T2

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

FLEXIBLE CIRCUIT BOARD REPAIRING

• Keep the temperature of soldering iron around 270 °C during

repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Legal Notice

The contents of each book pre-loaded on this

product are copyrighted works, edited with the

cooperation of the publisher.

product or the contents of this manual (illustrations,

related documents, etc.) in whole or in part without

the permission of the copyright holder. Additionally,

use of the data of this product or the contents of this

manual is not allowed without Sony’s permission

except for personal use.

Sony, the Sony logo,“Reader”, “BBeB” and their logos are

either trademarks or registered trademarks of Sony

Corporation.

EPUB is a registered trademark of the IDPF.

Frutiger, Univers, Helvetica and Palatino are trademarks of

Linotype Corp. registered in the United States Patent and

Trademark Oce and may be registered in certain

jurisdictions in the name of Linotype Corp. or its licensee

Linotype GmbH.

Bitstream is a registered trademark, and Dutch, Font

Fusion, and Swiss are trademarks, of Bitstream Inc.

Microsoft, Windows, Windows Vista and Windows Media

are trademarks or registered trademarks of Microsoft

Corporation in the United States and / or other countries.

Macintosh and Mac OS are trademarks of Apple Inc.,

registered in the U.S. and other countries.

This PRS-T2 contains Adobe® Reader® Mobile software

under license from Adobe Systems Incorporated, Copyright

reserved. Adobe and Reader are trademarks of Adobe

Systems Incorporated.

This product includes software developed by the OpenSSL

Project for use in the OpenSSL Toolkit. (http://www.

software written by Eric Young ([email protected]). This

product includes software written by Tim Hudson (tjh@

cryptsoft.com). For details on OpenSSL License, refer to

[End User License Agreement] in [About] at [Settings] on

the Reader.

Wi-Fi, the Wi-Fi CERTIFIED logo, WPA, WPA2 and Wi-Fi

Protected Setup are trademarks or registered trademarks

of Wi-Fi Alliance.

Facebook is a trademark of Facebook, Inc.

EVERNOTE, Evernote Clearly, the Evernote elephant logo

and REMEMBER EVERYTHING are trademarks of Evernote

Corporation, and used under licence.

Contains Reader® Mobile technology by Adobe Systems

Incorporated.

Google is a trademark of Google Inc.

All other system names and product names appearing

in this document are the registered trademarks or

trademarks of their respective owners. Further, the

trademark ™ and registered trademark ® symbols are

not indicated throughout this document.

Corporation

4-435-719-41(1)

1. SERVICING NOTES ............................................. 3

2. DISASSEMBLY

2-1. Disassembly Flow........................................................... 4

2-2. Rear Case Block.............................................................. 5

2-3. MAIN Board ................................................................... 6

2-4. Case Front Assy .............................................................. 7

2-5. Battery Assy (BAT1)....................................................... 8

2-6. Light Guide Assy (LG1) ................................................. 8

2-7. JACK Board, Chassis Assy (EII1).................................. 9

3. TEST MODE ............................................................ 10

4. EXPLODED VIEWS

4-1. Rear Case Section ........................................................... 16

4-2. Case Front, Battery Section ............................................ 17

4-3. Chassis Section ............................................................... 18

5. ACCESSORIES ....................................................... 19

TABLE OF CONTENTS

PRS-T2

NOTE THE EACH BOARDS REPAIRING

The mount parts on each boards installed in this set cannot ex-

change with single. When the each boards are damaged, exchange

the entire mounted board.

NOTE OF REPLACING THE COMPLETE MAIN BOARD

OR CHASSIS ASSY

Please do the following work when you exchange complete MAIN

board or CHASSIS ASSY.

Note: ELEMENT INK INDICATOR 6inch is included in CHASSIS

ASSY.

• REWRITING THE LUT:

Refer to “10. Update Waveform” on page 11.

• Write SP1 paramenter ﬁle:

Refer to “11. Update SP1 Parameters” on page 13.

• Write VCOM:

Refer to “16. Write VCOM” on page 14.

ABOUT THE LEAD WIRE OF BATTERY ASSY (BAT1)

Conﬁrm the operation after pressing the button of the main unit

bottom without fail when soldering the BATTERY ASSY (BAT1)

to the MAIN board.

MAIN board

soldering

battery assy (BAT1)

[RESET] button

NOTE OF REPLACING THE WLAN ANTENNA

Please do the following work when you exchange WLAN AN-

TENNA.

Manually setting a Wi-Fi connection

You can set up a Wi-Fi network connection manually

by inputting the required information for connection.

Make sure to turn on [Wi-Fi] and tap [Wi-Fi Settings] on

the [Wireless Network Settings] screen. Alternatively,

you can turn on [Wi-Fi] by tapping the status bar and

tapping [Wi-Fi Settings].

1Tap [Add Wi-Fi Network].

2Tap [Manual Registration].

3Tap the [SSID] input area and type in using the

on-screen keyboard.

4Tap the [Security Method] menu (the default

value is [Open]), and then tap the supported

security type.

5Tap the [Password] input area and type in your

password using the on-screen keyboard, and

then tap [Done] [Save].

6Tap the saved network SSID in the [Wi-Fi

Networks] list on the [Wi-Fi Settings] screen.

7If prompted for a password, tap the input area

and type in the password using the on-screen

keyboard.

8Tap [Connect].

The Reader connects to the Wi-Fi network.

The Wi-Fi connection status is displayed in the

status bar.

SECTION 1

SERVICING NOTES

PRS-T2

SECTION 2

DISASSEMBLY

• This set can be disassembled in the order shown below.

2-1. DISASSEMBLY FLOW

SET

2-2. REAR CASE BLOCK

(Page 5)

2-3. MAIN BOARD

(Page 6)

2-4. CASE FRONT ASSY

(Page 7)

2-5. BATTERY ASSY (BAT1)

(Page 8)

2-6. LIGHT GUIDE ASSY (LG1)

(Page 8)

2-7. JACK BOARD,

CHASSIS ASSY (EII1)

(Page 9)

PRS-T2

Note: Follow the disassembly procedure in the numerical order given.

2-2. REAR CASE BLOCK

Note: Please spread a sheet under a

unit not to injure case front.

2 four claws

6 five claws

7 five claws

4 five claws

rear case block

case front assy

Top side:

1 Insert the jig in the gap between rear

case block and case front assy.

Then slide it to arrow direction to remove

claws of rear case block.

9 rear case block

– Rear bottom side view –

5 Insert the jig in the gap between rear

case block and case front assy.

Then slide it to arrow direction to remove

claws of rear case block.

Left side: rear case block

case front assy

Right side: rear case block

case front assy

3 Insert the jig in the gap between rear

case block and case front assy.

Then slide it to arrow direction to remove

claws of rear case block.

•JIG

When disassembling the set, use the following jig.

Part No. Description

9-913-402-33 Tool for Disassembling

8 Remove the rear case block

in the direction of an arrow.

PRS-T2

2-3. MAIN BOARD

ditch MAIN board

MAIN board

WLAN antenna

(ANT1)

WLAN antenna wire

:/$1DQWHQQDZLUHVHWWLQJ

&RSSHUOHDI3:%VHWWLQJ

&RSSHUVKHHWVHWWLQJ

1sheet AL

3sheet (cable)

2WLAN antenna connector

9copper leaf (PWB)

copper leaf

(PWB)

0copper sheet 2

copper sheet 2

qa MAIN board

±5HDUERWWRPVLGHYLHZ±

5FPC M-J5047

6element INK indicator

flexible printed board

7shaft

(M1.4 uL1.6)

8screw

(M1.4 uL2)

8screw

(M1.4 uL2)

8screw

(M1.4 uL2)

8screw (M1.4 uL2)

8two screws

(M1.4 uL2) 8screw

(M1.4 uL2)

8screw

(M1.4 uL2)

8screw

(M1.4 uL2)

8screw

(M1.4 uL2)

Note 1: Please spread a sheet under a

unit not to injure case front.

Note 2: WLAN antenna wire must not run

aground to a boss.

4Remove three solders of battery wire.

Note 3: When soldering, refer to “ABOUT THE LEAD

WIRE OF BATTERY ASSY (BAT1)” (page 3).

MAIN board

%DWWHU\DVV\ZLUHVHWWLQJ

copper leaf

(PWB)

white red black

battery assy (BAT1)

sheet

(cable)

sheet AL

guide

line

guide

line

guide line battery assy (BAT1)

PRS-T2

2-4. CASE FRONT ASSY

– Rear bottom side view –

4Remove five claws in

order of the arrow A.

5Remove six claws in

order of the arrow B.

7Remove the chassis block.

6Remove six claws in

order of the arrow C.

8case front assy

3three tapping screws

(P2)

3tapping screw

(P2)

3two tapping screws

(P2)

1sheet AL

2WLAN antenna connector

MAIN board

WLAN antenna (ANT1)

WLAN antenna wire

• WLAN antenna wire setting

Note 1: Please spread a sheet under a

unit not to injure case front.

Note 2: WLAN antenna wire must not run aground to a boss.

ditch

sheet AL

guide

line

PRS-T2

2-5. BATTERY ASSY (BAT1)

2-6. LIGHT GUIDE ASSY (LG1)

– Rear bottom view –

1sheet (cable)

3battery assy (BAT1)

Note 1: Please spread a sheet under a

unit not to injure case front.

2Remove three solders of

battery wire.

Note 2: When soldering, refer

to “ABOUT THE LEAD

WIRE OF BATTERY

ASSY (BAT1)” (page 3).

MAIN board

• Battery assy wire setting

copper leaf

(PWB)

white red black

battery assy (BAT1)

sheet

(cable)

– Front bottom side view –

3light guide assy

(LG1)

1sheet switch flexible board

2three shafts

(light guide)

2three shafts

(light guide)

PRS-T2

– Front bottom view –

1two screws

(M1.4 L2)

1screw

(M1.4 L2)

6adhesive sheet

(4 3)

6adhesive sheet

(4 3)

6adhesive sheet

(4 3)

2claw

3Pull out FPC M-J5047

(FPC1) from the slit.

slit 7chassis assy

(EII1)

4FPC M-J5047

(FPC1)

FPC M-J5047 (FPC1)

convex part

5JACK board

JACK board

Note: When installing the FPC M-J5047 (FPC1),

confirm the inserted direction.

2-7. JACK BOARD, CHASSIS ASSY (EII1)

PRS-T2

SECTION 3

TEST MODE

PREPARATION OF THE TEST MODE

Prepare the following before executing the test mode.

• PC

• USB cable for PC connection (MICRO B)

• File for the test mode

Note: Conﬁrm the method of obtaining the ﬁle for test mode to each ser-

vice headquarters.

HOW TO ENTER THE TEST MODE

Procedure:

1. Press the [1] key to turn the power on.

2. Conﬁrm the HOME menu was completely displayed, and con-

nect this unit to PC by the USB cable (MICRO B).

3. Conﬁrm the USB connection screen displayed, and touch the

“Yes”.

Do you want the computer to recognize

this device?

Tap [Yes] to install ReaderTM for PC or ReaderTM for MacR

application, or transfer content.

Tap[No] to use Reader while charging.

Note: This screen will show whenever connecting with the

USB cable.

OFF

Yes No

4. The following screen is displayed in this unit, and conﬁrm the

“READER” drive of this unit is recognized on PC.

This device is correctly recognized by the

computer.

Check completion of the transfer by computer before

detaching USB cable.

5. Copy the ﬁle for the test mode from PC to directly under the

“READER” drive of this unit.

6. Remove this unit and USB cable (MICRO B) from PC.

7. Conﬁrm the HOME menu was completely displayed, and

press the key as following order.

[>] [ ] [<] [ ]

8. After a while, the test mode menu is displayed, and this unit

enters the test mode.

@Test Mode

Version: X.X.X

Target storage: Internal

Test Panal Update Waveform IR-LED Level

Drawing with

Points

Update SP1

Parameters Check 3G Module

TP Coordinate Check User

History

Test All Key Switch ADB

Test Battery Life Fake MoAkey

Version

Confirmation Reboot (Normal)

Check Battery Reboot (Recovery)

Set Sleep Timeout Radio Logcat

Get “traces.txt”

Factory Initialize

Re-fetch 3G

Identifier

Log Extact 2

(Flush)

Reset Device Lock

Power Off

Log Extract 1

Check

Temperature

Write VCOM

WWAN ON

WWAN OFF

(Screen display)

RELEASING THE TEST MODE

Procedure:

1. Press the [ ] key, and conﬁrm the HOME menu was com-

pletely displayed.

2. Connect this unit to PC by the USB cable (MICRO B).

3. Conﬁrm the USB connection screen displayed, and touch the

“Yes”.

Do you want the computer to recognize

this device?

Tap [Yes] to install ReaderTM for PC or ReaderTM for MacR

application, or transfer content.

Tap[No] to use Reader while charging.

Note: This screen will show whenever connecting with the

USB cable.

OFF

Yes No

4. The following screen is displayed in this unit, and conﬁrm the

“READER” drive of this unit is recognized on PC.

This device is correctly recognized by the

computer.

Check completion of the transfer by computer before

detaching USB cable.

5. Delete the ﬁle for the test mode from directly under the

“READER” drive of this unit.

6. Remove this unit and USB cable (MICRO B) from PC.

7. Conﬁrm the HOME menu was completely displayed, and press

the key as following order, and conﬁrm that the test mode does

not enter.

[>] [ ] [<] [ ]

8. Press the [1] key for 5 seconds or more, and touch the “Yes”

to turn the power off.

Note: Never forget to delete the ﬁle for the test mode.

Andere Handbücher für Reader PRS-T2

Inhaltsverzeichnis

Andere Sony E-Book-Reader Handbücher

Sony

Sony PRS-950 - Reader Daily Edition&trade Bedienungsanleitung

Sony

Sony PRS-505 Bedienungsanleitung

Sony

Sony PSR-600 Bedienungsanleitung

Sony

Sony PRS-950SC - Reader Daily Edition&trade Bedienungsanleitung

Sony

Sony PRS-300RC/B - Reader Pocket Edition Bedienungsanleitung

Sony

Sony DPT-S1 Bedienungsanleitung

Sony

Sony PRS-T1 Betriebsanleitung

Sony

Sony Reader PRS-T2 Bedienungsanleitung

Sony

Sony PRS-350PC - Reader Pocket Edition&trade Bedienungsanleitung

Sony

Sony PRS-300SC Bedienungsanleitung

Sony

Sony Reader 4-151-151-13(1) Bedienungsanleitung

Sony

Sony Reader PRS-300 Bedienungsanleitung

Sony

Sony PRS-350SC - Reader Pocket Edition&trade Bedienungsanleitung

Sony

Sony Reader PRS-T3 Series Bedienungsanleitung

Sony

Sony PRS-650RC - Reader Touch Edition&trade Bedienungsanleitung

Sony

Sony PRS-505 Bedienungsanleitung

Sony

Sony PRS-500 Bedienungsanleitung

Sony

Sony PRS-T1 Bedienungsanleitung

Sony

Sony 3803775 Bedienungsanleitung

Sony

Sony PRS-505 Bedienungsanleitung

Sony

Sony PRS-650 - Reader Touch Edition&trade Bedienungsanleitung

Sony

Sony PRS-300 - Reader Pocket Edition&trade Bedienungsanleitung

Sony

Sony PRS-950 - Reader Daily Edition&trade Bedienungsanleitung

Sony

Sony PRS-600 - Electronic Book Reader Bedienungsanleitung

Beliebte E-Book-Reader Handbücher anderer Marken

Denver

Denver EBO-500 Bedienungsanleitung

Orbit Research

Orbit Research Reader 20 Bedienungsanleitung

Amazon

Amazon Kindle Kindle 1 Bedienungsanleitung

Franklin

Franklin DFC-3015 Bedienungsanleitung

IEI Technology

IEI Technology AFL2-EM-RFID-KIT Bedienungsanleitung

Pocketbook

Pocketbook РВ 903 Bedienungsanleitung

Polaroid

Polaroid PER70Z Bedienungsanleitung

Kobo

Kobo GLO HD Bedienungsanleitung

Onyx International

Onyx International SMART READING Series Bedienungsanleitung

Air Techniques

Air Techniques ScanX ULR01.1A1 Bedienungsanleitung

Aluratek

Aluratek AEBK01FS Bedienungs- und Wartungshandbuch

Cocoon

Cocoon BK7021 Bedienungsanleitung

Yarvik

Yarvik EBR070 GoBook Bedienungsanleitung

Obreey

Obreey Pocketbook 360 Plus Bedienungsanleitung

Franklin

Franklin BOOKMAN NIV-440 Bedienungsanleitung

Icarus

Icarus Sense E651SR Bedienungsanleitung

Amazone

Amazone Kindle Bedienungsanleitung

Aluratek

Aluratek Libre color AEBK07FS Bedienungs- und Wartungshandbuch