Sony SAL-135F18Z - 135mm f/1.8 Carl Zeiss Sonnar T Telephoto... Bedienungsanleitung

SERVICE NOTE

SPECIFICATIONS

REPAIR PARTS LIST

DISASSEMBLY ADJUSTMENTS

SERVICE MANUAL

Link

Revision History

How to use

Acrobat Reader

How to use

Acrobat Reader

Sony EMCS Co.

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

Ver. 1.4 2007.12

LENS FOR DSLR CAMERA

2007L0800-1

Published by KohdaTEC9-852-110-12

US Model

Canadian Model

AEP Model

Chinese Model

SAL135F18Z

(Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

• About the Special Driver

• About the Lens Test Projector and Finished Inspection JIG

• About the Screw Filter Frame Assy.

• About the MTF measurement.

Revised-1

Replace the previously issued

SERVICE MANUAL 9-852-110-11

with this Manual.

— 2 —

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

SPECIFICATIONS

• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.

• Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused

at infinity.

Equivalent 35mm-format focal length*1(mm)

202.5

*1The value for equivalent 35mm-format focal length is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized image sensor.

Lens groups elements

8-11

Angle of view 1*2

18°

Angle of view 2*2

12°

*2The value of angle of view 1 is based on 35mm-format cameras, and that of angle of view 2 is based on Digital Single Lens Reflex Cameras

equipped with an APS-C sized image sensor.

Minimum focus (m (feet))*3

0.72 (2.4)

*3Minimum focus is the shortest distance from the image sensor to the subject.

Maximum magnification (××

××

×)

0.25

Minimum f-stop

f/22

Filter diameter (mm)

Dimensions (maximum diameter ××

××

×height) (mm (in.))

Approx. 88 ×114.5 (3 1/2 ×4 5/8)

Mass (g (oz.))

Approx. 995 (35 1/8)

Included items

Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Lens case (1), Set of printed documentation

Designs and specifications are subject to change without notice.

— 3 —

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

TABLE OF CONTENTS

Section Title Page

1. SERVICE NOTE

1-1. Chemicals ·······································································1-1

1-2. Exterior Parts··································································1-1

1-3. Unleaded Solder ·····························································1-1

1-4. Safety Check-out ····························································1-2

1-5. Troubleshooting ·····························································1-3

2. DISASSEMBLY

2-1. Disassembly ···································································2-2

3. REPAIR PARTS LIST

3-1. Exploded Views ······························································3-1

3-2. Supplied Accessories······················································3-4

4. ADJUSTMENTS

4-1. Preparations····································································4-1

4-2. Aperture Diameter Check/Adjustment·························4-13

4-3. Projective Resolving Power Check ······························4-20

4-4. Flange Back (f’F) Check/Adjustment ··························4-23

4-5. Focus-Shift Check/Adjustment (Aperture) ··················4-26

4-6. Torque Ring Play Adjustment ······································4-27

4-7. Lens ROM Check·························································4-28

4-8. Focus Brush Position Check/Adjustment·····················4-30

4-9. Focus Hold Button Check (Focus Hold Button) ··········4-36

4-10. Focus Hold Button Check

(Focus Hold Button Short) ···········································4-38

4-11. Write dSB·····································································4-41

1-1

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

1. SERVICE NOTE

1-1. Chemicals

Some chemicals used for servicing are highly volatile.

Their evaporation caused by improper management affects your health and environment, and wastes resources.

Manage the chemicals carefully as follows.

•Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.

•Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.

•Keep containers sealed to avoid natural evaporation when chemicals are not in use.

•Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and

use up it.

1-2. Exterior Parts

Be careful to the following points for exterior parts used in this unit.

•Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts.Avoid using chemicals.

Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.

•Insert the specific screws vertically to the part when installing a exterior part.

Be careful not to tighten screws too much.

1-3. Unleaded Solder

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Be careful to the following points to solder or unsolder.

•Set the soldering iron tip temperature to 350 °C approximately.

If cannot control temperature, solder/unsolder at high temperature for a short time.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing

unleaded solder and leaded solder will cause detachment phenomenon.

1-2

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

1-4. SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and

bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the

customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their

replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 °C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

SAFETY-RELATED COMPONENTWARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH

MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION

Dangerofexplosionifbatteryisincorrectlyreplaced.

Replace only with the same or equivalent type.

1-5. MTF Measurement

In case of replacement or disassembling the effective parts against performance, be sure to perform MTF measurement.

Please consult a related headquarters about service information.

Ver. 1.4 2007.12

The changed portions from

Ver. 1.3 are shown in blue.

1-3

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

1-5. TROUBLESHOOTING

1-5-1. ApertureTrouble

Check operation of

the preset ring.

Replace the defective part.

Check operation of the

preset ring, and replace

the defective part.

Perform the aperture

diameter adjustment.

(See page 4-16.)

Perform the aperture

diameter check.

(See page 4-13.)

Check operation

of the diaphragm

control block.

OK OK

Function NG F No. NG

Aperture trouble

Replace the defective part.

NGNG

END

Perform the aperture

diameter check.

(See page 4-13.)

1-4

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

Check the operation

again.

Replace the defective part

or apply the grease.

Function NG Position NG

Focus trouble

Replace the defective part

or apply the grease.

Check the coupler.

Check the focus 1 cam

ring assy and focus 2

cam ring block.

NGNG

END

Check the installation of

the F-ECD flexible.

Reinstall the F-ECD flexible.

Check pattern

of the F-ECD flexible.

Clean the pattern of the

F-ECD flexible.

Replace the

F-ECD flexible.

Perform the focus brush

position check/adjustment

(See page. 4-30.)

1-5-2. FocusTrouble

2-1

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

Cut and remove the part of gilt

which comes off at the point.

(Be careful or some

pieces of gilt may be left inside)

2. DISASSEMBLY

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, dont’press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

UNIVERSALWRENCH

In case of the following notches or holes are located in the lens block, etc during disassembling/

assembling the lens, Use the universal wrench.

How to Use

Attach the chip-A or chip-B to the universal wrench.

For the notches: chip-A

For the holes: chip-B

Match the universal wrench to the holes or notches of the lens block, etc.

When top of tip does not reach holes or notches because the fixed screw becomes obstructive,

replace the fixed screw to below.

+B 3X5 7-682-546-09

Notches Holes

Universal wrench

J-6082-609-A

Chip-A for

universal wrench:

J-6082-609-1

Chip-B for

universal wrench:

J-6082-609-2

Notches

Chip-A

Chip-B

Chip

Fixed screw

Chip

Match the universal wrench

to the width of holes or notches. Universal wrench

Holes

2-2

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

2-1. DISASSEMBLY

Note 1:

Remove the filter screw frame using the filter screw frame removing tool.

Filter screw frame removing tool: J-6082-649-A

Note 2:

When removing or installing the parts of side of lens mount, install the filter screw frame to lens.

If removing or installing the parts of side of lens mount after the filter screw frame is removed, be careful to avoid damaging the 1 lens

block.

Note 3:

Remove the screw (Ref. No. 15 or 61, 2-897-949-01 screw (3ULR-F M1.7x1.6(C3C))) using the special driver.

Special driver: J-6082-654-A

Shape of head

2-3

SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T*135mm F1.8 ZA)

2-1-1. OUTER BARREL BLOCK, MOUNT BLOCK AND LIGHT SHIELD RING BLOCK

EXPLODEDVIEW

HELP01

HELP10

HELP07

HELP09

HELP11

HELP02

HELP03

HELP08

HELP05

HELP04

HELP06

HELP12

(See Page 2-4.)

HELP07

1Screw Filter Frame

Assy

Function Lever

Preset Ring

!- Rear Ring Assy

9Contact Flexible

Guide

!= PWB Flexible Main

Assy

2Draw Ring Assy

3Focus Ring

!/ Main Spring

Guide

5Contact Flexible

4Ligth Shield Ring Block

6Mount Block

![ Outer Barrel Block

7Coupler Receive

APERTURE

DIAMETER

ADJUSTMENT

FLANGE BACK

ADJUSTMENT

TOUQUE RING PLAY

ADJUSTMENT

•In case the removing of screw filter frame assy :

Before removing the screw filter frame assy, lubricate a small solvent (alcohol) to a gap

between screw filter frame assy and draw ring assy, hereby dissolve the adhesive bond.

Then remove it.

•About the screw filter frame assy :

Be sure avoiding replacement of screw filter frame assy as far as possible. If replacement of

it should be need, you convey the message to your user that changing of the Carl Zeiss

Serial No. is needed, and then you may obtain user’s agreement, and it replace.

Note:

Andere Handbücher für SAL-135F18Z - 135mm f/1.8 Carl Zeiss Sonnar T Telephoto...

Inhaltsverzeichnis

Andere Sony Linse Handbücher

Sony

Sony SEL135F18GM Bedienungsanleitung

Sony

Sony VF-37PK S Bedienungsanleitung

Sony

Sony VCL-918BY Bedienungsanleitung

Sony

Sony G Master SEL100400GM Bedienungsanleitung

Sony

Sony E 30 mm F3.5 Macro Bedienungsanleitung

Sony

Sony VPLL-Z2019 Bedienungsanleitung

Sony

Sony Alpha E 4/PZ 18-110 G OSS Bedienungsanleitung

Sony

Sony E 16mm F2.8 Bedienungsanleitung

Sony

Sony SAL50F14Z Bedienungsanleitung

Sony

Sony VCL-ES06 Bedienungsanleitung

Sony

Sony VCL-MHG07 - HIGH GRADE 0.7X WIDE-ANGLE LENS Bedienungsanleitung

Sony

Sony VPLL-3003 Bedienungsanleitung

Sony

Sony G MASTER SEL2470GM2 Bedienungsanleitung

Sony

Sony VPLL-CT10 Bedienungsanleitung

Sony

Sony G Master FE 12-24mm F2.8 GM Bedienungsanleitung

Sony

Sony SCL-P11X15 Bedienungsanleitung

Sony

Sony SEL2470Z Bedienungsanleitung

Sony

Sony SAL70200G2 Bedienungsanleitung

Sony

Sony VPLL-3050 Bedienungsanleitung

Sony

Sony LKRL-Z200 Series Bedienungsanleitung

Sony

Sony SEL2470Z Bedienungsanleitung

Sony

Sony VCL-610WEA Bedienungsanleitung

Sony

Sony SEL2470GM Bedienungsanleitung

Sony

Sony VCL-07FE Bedienungsanleitung

Beliebte Linse Handbücher anderer Marken

Panasonic

Panasonic Lumix H-ES12060 Installationsanleitung

Navitar

Navitar 1-62314 Leitfaden

Angenieux

Angenieux OPTIMO PRIME Bedienungsanleitung

Sealife

Sealife SL050 Bedienungsanleitung

Navitar

Navitar 1-51200 Leitfaden

MeCan

MeCan NY1S-a5100 Bedienungsanleitung

Tamron

Tamron SP 70-300mm F/4-56 Di VC USD Bedienungsanleitung

FujiFilm

FujiFilm FUJINON ZA17x7.6BERD-S6 Bedienungsanleitung

Panasonic

Panasonic VW-W4907 Bedienungsanleitung

Navitar

Navitar 1-51332 Leitfaden

Leica

Leica APO-SUMMICRON-SL 1:2/50 ASPH. Bedienungsanleitung

Cosina

Cosina Voigtländer SUPER NOKTON 29mm F0.8... Bedienungsanleitung

Arax

Arax PCS ARSAT H(K) 4.5/55 Bedienungsanleitung

Cosina

Cosina Voigtländer NOKTON Bedienungsanleitung

Cosina

Cosina Voigtländer NOKTON Bedienungsanleitung

Navitar

Navitar 1-51338 Leitfaden

Shamir

Shamir Star Einrichtungshandbuch

Canon

Canon J11ex4.5B Bedienungsanleitung