Sony DSX-A55BT Bedienungsanleitung

DSX-A55BT

4-475-462-31(1)

FM/MW/SW

Digital Media

Player

Operating Instructions GB

To cancel the demonstration (DEMO) display, see page 17.

2GB

Note on the lithium battery

Do not expose the battery to excessive heat

such as direct sunlight, fire or the like.

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR

ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL DAMAGES OR OTHER

DAMAGES INCLUDING, WITHOUT LIMITATION,

LOSS OF PROFITS, LOSS OF REVENUE, LOSS

OF DATA, LOSS OF USE OF THE PRODUCT OR

ANY ASSOCIATED EQUIPMENT, DOWNTIME,

AND PURCHASER’S TIME RELATED TO OR

ARISING OUT OF THE USE OF THIS PRODUCT,

ITS HARDWARE AND/OR ITS SOFTWARE.

IMPORTANT NOTICE!

Safe and efficient use

Changes or modifications to this unit not

expressly approved by Sony may void the

user’s authority to operate the equipment.

Please check for exceptions, due to national

requirement or limitations, in usage of

BLUETOOTH equipment before using this

product.

Driving

Check the laws and regulations on the use of

cellular phones and handsfree equipment in

the areas where you drive.

Always give full attention to driving and pull

off the road and park before making or

answering a call if driving conditions so

require.

Connecting to other devices

When connecting to any other device, please

read its user guide for detailed safety

instructions.

Be sure to install this unit in the dashboard of

the car for safety.

For installation and connections, see the

supplied installation/connections manual.

Warning if your car’s ignition has no ACC

position

Be sure to set the AUTO OFF function

(page 17). The unit will shut off completely

and automatically in the set time after the

unit is turned off, which prevents battery

drain. If you do not set the AUTO OFF

function, press and hold OFF until the display

disappears each time you turn the ignition

off.

Notes on BLUETOOTH function

3GB

Radio frequency exposure

RF signals may affect improperly installed or

inadequately shielded electronic systems in

cars, such as electronic fuel injection

systems, electronic antiskid (antilock)

braking systems, electronic speed control

systems or air bag systems. For installation

or service of this device, please consult with

the manufacturer or its representative of

your car. Faulty installation or service may be

dangerous and may invalidate any warranty

that may apply to this device.

Consult with the manufacturer of your car to

ensure that the use of your cellular phone in

the car will not affect its electronic system.

Check regularly that all wireless device

equipment in your car is mounted and

operating properly.

Emergency calls

This BLUETOOTH car handsfree and the

electronic device connected to the handsfree

operate using radio signals, cellular, and

landline networks as well as user-

programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any

electronic device for essential

communications (such as medical

emergencies).

Remember, in order to make or receive calls,

the handsfree and the electronic device

connected to the handsfree must be

switched on in a service area with adequate

cellular signal strength.

Emergency calls may not be possible on all

cellular phone networks or when certain

network services and/or phone features are

in use.

Check with your local service provider.

4GB

Table of Contents

Guide to Parts and Controls . . . . . . . . . . . . . .5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . . 7

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . 7

Preparing a BLUETOOTH Device. . . . . . . . . . .8

Connecting a USB Device . . . . . . . . . . . . . . . .9

Connecting Other Portable Audio

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Listening to the Radio

Listening to the Radio. . . . . . . . . . . . . . . . . . 10

Using Radio Data System (RDS) . . . . . . . . . . 11

Playback

Playing a USB Device . . . . . . . . . . . . . . . . . . 12

Playing a BLUETOOTH Device. . . . . . . . . . . . 12

Searching and Playing Tracks. . . . . . . . . . . . 13

Handsfree Calling

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . 14

Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . 15

Available Operations during Call . . . . . . . . . 16

Settings

Canceling the DEMO Mode . . . . . . . . . . . . . 17

Basic Setting Operation . . . . . . . . . . . . . . . . 17

General Setup . . . . . . . . . . . . . . . . . . . . . . . . 17

BT INIT (BLUETOOTH initialize) . . . . . . . . 18

Sound Setup . . . . . . . . . . . . . . . . . . . . . . . . . 18

EQ3 PRST (EQ3 preset). . . . . . . . . . . . . . . 18

EQ3 LOW, EQ3 MID, EQ3 HIGH . . . . . . . . 18

BLUETOOTH Setup . . . . . . . . . . . . . . . . . . . . 19

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . .24

5GB

Guide to Parts and Controls

The number 2/ALBUM button has a tactile dot.

(browse) (page 13)

Enter the browse mode during playback.

SOURCE

Turn on the power.

Change the source.

-OFF

Press and hold for 1 second to turn off

the power.

Press and hold for more than 2 seconds

to turn off the power and the display.

If the unit is turned off and the display

disappears, it is unable you to operate

with the remote.

Control dial

Rotate to adjust the volume.

ENTER

Enter the selected item.

SELECT

Enter sound setting.

Press and hold to open the general setup

menu.

(handsfree)

Receive/end a call.

CALL

Enter the call menu.

Press and hold more than 2 seconds to

switch the BLUETOOTH signal.

Display window

Main unit

6GB

(back)

Return to the previous display.

MODE (page 10, 16)

(front panel release)

SEEK +/–

Tune in radio stations automatically.

Press and hold to tune manually.

/(prev/next), /

(reverse/fast-forward)

Receptor for the remote commander

PTY (program type)

Select PTY in RDS.

Number buttons

Receive stored radio stations. Press and

hold to store stations.

Call a stored phone number. Press and

hold to store a phone number.

ALBUM /

Skip an album for audio device. Press and

hold to skip albums continuously.

PAUSE

SHUF (shuffle)

MIC (page 16)

DSPL (display)

Change display items.

-SCRL (scroll)

Press and hold to scroll a display item.

USB port

AUX input jack

The VOL (volume) + button has a tactile dot.

Remove the insulation film before use.

()/()

VOL (volume) +/–

SOUND

Open the sound setup menu directly.

-MENU

Press and hold to open the general setup

menu.

(+)/(–)

RM-X231 Remote

7GB

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1Press and hold OFF .

The unit is turned off.

2Press , then remove the panel

by pulling it towards you.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel,

the caution alarm will sound for a few

seconds. The alarm will only sound if the

built-in amplifier is used.

Setting the Clock

1Press and hold SELECT.

The setup display appears.

2Rotate the control dial to select

[CLOCK-ADJ], then press it.

The hour indication flashes.

3Rotate the control dial to set the

hour and minute.

To move the digital indication, press SEEK

+/–.

4After setting the minute, press

SELECT.

The setup is complete and the clock

starts.

To display the clock, press DSPL.

Getting Started

Attaching the front panel

8GB

Preparing a BLUETOOTH

Device

You can enjoy music, or perform handsfree

calling, by connecting a suitable BLUETOOTH

device. For details on connecting, refer to the

operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, loud sound

may result.

When connecting a BLUETOOTH device

(cellular phone, audio device, etc.) for the

first time, mutual registration (called

“pairing”) is required. Pairing enables this

unit and other devices to recognize each

other.

1Place the BLUETOOTH device within

1 m (3 ft) of this unit.

2Press CALL, rotate the control dial to

select [PAIRING], then press it.

flashes.

The unit enters pairing standby mode.

3Perform pairing on the BLUETOOTH

device so it detects this unit.

4Select [Sony Automotive] shown in

the display of the BLUETOOTH

device.

If [Sony Automotive] does not appear,

repeat from step 2.

5If passkey*input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “passcode,” “PIN

code,” “PIN number” or “Password,” etc.,

depending on the device.

When pairing is made, stays lit.

6Select this unit on the BLUETOOTH

device to establish the BLUETOOTH

connection.

or lights up when the connection is

made.

Note

While connecting to a BLUETOOTH device, this unit

cannot be detected from another device. To enable

detection, enter the pairing mode and search for

this unit from another device.

To cancel pairing

Perform step 2 to cancel the pairing mode

after this unit and the BLUETOOTH device are

paired.

Pairing and connecting with a

BLUETOOTH device

[0000]

Input passkey

9GB

To use a paired device, connection with this

unit is required. Some paired devices will

connect automatically.

1Press CALL, rotate the control dial to

select [BT SIGNL], then press it.

Make sure that lights up.

2Activate the BLUETOOTH function

on the BLUETOOTH device.

3Operate the BLUETOOTH device to

connect to this unit.

or lights up.

Icons in the display:

To connect the last-connected device

from this unit

Activate the BLUETOOTH function on the

BLUETOOTH device.

Press SOURCE.

Select [BT PHONE] or [BT AUDIO].

Press (handsfree) to connect with the

cellular phone, or PAUSE to connect with the

audio device.

Note

While streaming BLUETOOTH audio, you cannot

connect from this unit to the cellular phone.

Connect from the cellular phone to this unit

instead.

Tip

With BLUETOOTH signal on: when the ignition is

turned to on, this unit reconnects automatically to

the last-connected cellular phone.

Connecting a USB Device

1Turn down the volume on the unit.

2Connect the USB device to the unit.

Connecting with a paired

BLUETOOTH device

Lights up when a cellular phone is

connected to the unit.

Lights up when an audio device is

connected to the unit.

10GB

Connecting Other Portable

Audio Device

1Turn off the portable audio device.

2Turn down the volume on the unit.

3Connect the portable audio device

to the AUX input jack (stereo mini

jack) on the unit with a connecting

cord (not supplied)*.

* Be sure to use a straight type plug.

4Press SOURCE to select [AUX].

To match the volume level of the

connected device to other sources

Start playback of the portable audio device

at a moderate volume, and set your usual

listening volume on the unit.

Press SELECT, and rotate the control dial to

select [AUX VOL] (page 18).

Listening to the Radio

To listen to the radio, press SOURCE to select

[TUNER].

1Press MODE to change the band.

2Press and hold SELECT (FM1, FM2,

FM3, MW, SW1 or SW2).

The setup display appears.

3Rotate the control dial to select

[BTM], then press it.

The unit stores stations in order of

frequency on the number buttons.

1Press MODE to change the band

(FM1, FM2, FM3, MW, SW1 or SW2).

2Perform tuning.

To tune manually

Press and hold SEEK +/– to locate the

approximate frequency, then press SEEK

+/– repeatedly to fine adjust to the

desired frequency.

To tune automatically

Press SEEK +/–.

Scanning stops when the unit receives a

station. Repeat this procedure until the

desired station is received.

Listening to the Radio

Storing automatically (BTM)

Tuning

Andere Handbücher für DSX-A55BT

Inhaltsverzeichnis

Andere Sony Medienplayer Handbücher

Sony

Sony NSZ-GS7 Bedienungsanleitung

Sony

Sony NW-ZX707 Referenzhandbuch

Sony

Sony DMXWL1 - BRAVIA Wireless HD Link Bedienungsanleitung

Sony

Sony SMP-NX20 Bedienungsanleitung

Sony

Sony LDP-1000A Bedienungsanleitung

Sony

Sony SMP-NX20 Gebrauchs- und Wartungshandbuch

Sony

Sony Walkman NWZ-E443K Bedienungsanleitung

Sony

Sony NW-A100TPS Referenzhandbuch

Sony

Sony NW-WM1AM2 Bedienungsanleitung

Sony

Sony HAP-S1 Bedienungsanleitung

Sony

Sony DSX-S210X Produkthandbuch

Sony

Sony Walkman NW-S603 Bedienungsanleitung

Sony

Sony NSP-1 Bedienungsanleitung

Sony

Sony NW-ZX706 Bedienungsanleitung

Sony

Sony DSX-A200UI Bedienungsanleitung

Sony

Sony SMPU10 - USB Media Player Bedienungsanleitung

Sony

Sony NSP-100 Installations- und Betriebshandbuch

Sony

Sony FMP-X1 Bedienungsanleitung

Sony

Sony VSP-BZ10 Bedienungsanleitung

Sony

Sony Walkman NWZ-A726 Bedienungsanleitung

Sony

Sony LLS-201 Bedienungsanleitung

Sony

Sony SMP-N100 Bedienungsanleitung

Sony

Sony WALKMAN NW-ZX505 Referenzhandbuch

Sony

Sony Network Walkman NW-E403 Bedienungsanleitung

Beliebte Medienplayer Handbücher anderer Marken

Visual Land

Visual Land Impulse Bedienungsanleitung

limHD

limHD 200i Bedienungsanleitung

Transcend

Transcend DMP10 Bedienungsanleitung

Philips

Philips GoGear Muse SA2MUS08 Bedienungsanleitung

Fantec

Fantec MM-HDRL Bedienungsanleitung

Dune HD

Dune HD Duo 4K Bedienungsanleitung

IAdea

IAdea HMP-505S Bedienungsanleitung

Camos

Camos MMS-1000 Bedienungsanleitung

Energy

Energy 75 Series Bedienungsanleitung

Z3 Technology

Z3 Technology DME-03 Bedienungsanleitung

Meicheng

Meicheng HD-1080K12 Bedienungsanleitung

DENAFRIPS

DENAFRIPS ARCE Bedienungsanleitung

Topaz

Topaz CMS Media Player Gebrauchsanweisung

InFocus

InFocus LightCast Bedienungsanleitung

IconBiT

IconBiT XDS1003D Bedienungsanleitung

Quanmax

Quanmax QDSP-2090 Series Bedienungsanleitung

Samsung

Samsung MP-80S Bedienungsanleitung

Trigon Elektronik

Trigon Elektronik CHRONOLOG Bedienungsanleitung