Sony NSBK-DH05 Bedienungsanleitung
4-409-869-02 (1)
© 2011 Sony Corporation
Display
Accelerator
Board
NSBK-DH05
お買い上げいただきありがとうございます。
電気製品は安全のための注意事項を守らないと、
火災や人身事故になることがあります。
この取扱説明書には、事故を防ぐための重要な注意事項と製品の
取り扱いかたを示してあります。この取扱説明書をよくお読みのうえ、
製品を安全にお使いください。お読みになったあとは、
いつでも見られるところに必ず保管してください。
Installation Manual ________ GB
設置説明書 ________________ JP
Manuel d’installation ______ FR
Installationsanleitung ______ DE
Manuale all’installazione ___ IT
Manual de instalacion _____ ES
2Note to Customers
Note to
Customers
Please contact your local Sony
representative or dealer to request
installation of this unit.
Attempting to perform the installation
procedures described in this manual
yourself may result in fire, electrical shock,
or severe injury.
Do not attempt installation yourself.
Before operating the unit, please read this
manual thoroughly and retain it for future
reference.
ATTENTION
The electromagnetic fields at the specific
frequencies may influence the picture of
this unit.
For the customers in the U.S.A.
This equipment has been tested and found
to comply with the limits for a Class A
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference
in which case the user will be required to
correct the interference at his own expense.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
All interface cables used to connect
peripherals must be shielded in order to
comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC
Rules.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
For the customers in Canada
This Class A digital apparatus complies
with Canadian ICES-003.
English
3
Precautions
GB
For the customers in Europe,
Australia and New Zealand
WARNING
This is a Class A product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
For the customers in Europe
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan, Minato-ku,
Tokyo, 108-0075 Japan.
The Authorized Representative for EMC
and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany. For any service or
guarantee matters please refer to the
addresses given in separate service or
guarantee documents.
This apparatus shall not be used in the
residential area.
Інформація для споживачів в
Україні.
Обладнання відповідає вимогам:
- Технічного регламенту обмеження
використання деяких небезпечних
речовин в електричному та
електронному обладнанні
(постанова КМУвід 03/12/2008 №
1057).
Precautions
To the technician installing
the unit
• Please refer to the Installation Manual
supplied with the NSR-500 series for
installation instructions.
• Before installing the unit, be sure to
unplug the NSR-500 and wait until the
internal temperature drops.
4Overview / Package Contents
Overview
This product is a display accelerator board
for the Sony NSR-500 Network
Surveillance Server.
When installed in a slot on the main unit,
this board enables enhanced video
playback.
Supported models and versions
NSR-500 V.1.5.1 or later
For details on settings for the NSR-500
main unit and how to confirm or update the
version, refer to the User’s Guide (4-272-
495-15 (1) or later) (CD-ROM) for the
NSR-500 series.
Supported monitors
The monitors that can be used after
installing this board include HDMI-
compatible devices and computer displays
that accept analog RGB input. The
supported resolutions are as follows.
• Full HD (1,920 × 1,080)
• WUXGA (1,920 × 1,200)
(analog RGB output (monitor connector
2) only)
• Full Wide XGA (1,360 × 768)
• UXGA (1,600 × 1,200)
• SXGA (1,280 × 1,024)
• XGA (1,024 × 768)
Package Contents
Check that the following items are included
in this package:
• Display accelerator board (1)
• Analog RGB cable (1)
• Connector cover (1)
• Installation Manual (this document) (1)
• Warranty booklet (1)
This package may contain additional
hardware and/or documentation.
Note
Note
5
Parts Identification
Parts Identification
Display Accelerator Board (installed on NSR-500)
AHDMI output connector
Use this connector to connect a monitor
that supports HDMI input.
BMonitor connector 2
Use this connector to connect a monitor
that supports analog RGB input.
• After this board is installed, monitor
connector 1 will no longer be available
for use. Only monitor connector 2 will be
available.
• Monitor connector 2 and the HDMI
output connector cannot be used at the
same time.
1
2
Caution
6Preparation Steps / Step 1: Installing the Display Accelerator Board on the NSR-500
Preparation Steps Step 1: Installing
the Display
Accelerator Board
on the NSR-500
• Perform installation work in an antistatic
environment.
• Before installing the display accelerator
board, be sure to turn off and unplug the
NSR-500 and wait until the internal
temperature drops.
1Remove the three screws (B3 × 6
(black)) on the rear panel of the
NSR-500 and the two screws (K3 × 5)
on the side panels, and then remove the
chassis cover in the direction of the
arrow.
Step 1: Installing the Display
Accelerator Board on the NSR-500
(page 6)
r
Step 2: Connecting the Monitor
(page 9)
r
Step 3: Configuring Settings for the
NSR-500 Main Unit
Refer to the User’s Guide (PDF) for the
NSR-500 series, and configure the
[Monitor] and [Audio] settings in the
[Setup Menu].
r
Step 4: Verifying Operation
Verify that images are displayed on the
connected monitor.
r
Installation Complete
Caution
Screws
(B3 × 6 (black))
Screw
(K3 × 5)
Chassis cover
Screw
(K3 × 5)
7
Step 1: Installing the Display Accelerator Board on the NSR-500
2Confirm the installation position.
3Pull the protection cover upward and
remove it.
4Insert the display accelerator board
with the proper orientation.
5Install the display accelerator board.
Make a visual check at the following
two points and confirm that the board
is firmly connected.
Incomplete and/or skewed insertion of
the board can cause improper
connection.
Install the display
accelerator board here.
Rear panel side
Caution
Make a visual check.
8Step 1: Installing the Display Accelerator Board on the NSR-500
6Remove the protective cover for
monitor connector 2.
If secured by screws
Use a Phillips screwdriver to remove
the two screws securing the protective
cover.
If not secured by screws
Push in the protective cover from the
outside of the unit with a screwdriver,
for example.
7Remove the two hex cap screws on the
supplied RGB cable.
8Pass the 15-pin D-sub connector
through the slot for monitor connector
2 from the inside of the unit, and secure
the two hex cap screws to the
connector from the outside of the unit.
9
Step 2: Connecting the Monitor
9Orient the analog RGB cable properly,
and connect it to the connector (J5) on
the display accelerator board.
Be sure to verify that the cable is
connected securely.
10
Attach the supplied connector cover to
monitor connector 1.
11
Reinstall the chassis cover by
performing the procedure of step 1in
reverse order.
Step 2:
Connecting the
Monitor
Connect the monitor to monitor connector 2
or the HDMI monitor connector.
• When monitors are connected via a
monitor switch, images may not always
display. We recommend connecting
monitors directly to the unit.
• Monitor connector 2 and the HDMI
monitor connector cannot be used at the
same time.
Caution
or
HDMI monitor connector
Monitor connector 2
10 Specifications
Specifications
Display accelerator board
External connector
HDMI output (1)
Analog RGB output (1)
Design and specifications are subject to
change without notice.
Notes
Always verify that the unit is operating
properly before use. SONY WILL NOT
BE LIABLE FOR DAMAGES OF ANY
KIND INCLUDING, BUT NOT LIMITED
TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF
THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO
FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD
OR AFTER EXPIRATION OF THE
WARRANTY, OR FOR ANY OTHER
REASON WHATSOEVER.
Trademarks
• “IPELA” and are
trademarks of Sony Corporation.
• HDMI, HDMI logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI
Licensing LLC.
• Other products or system names
appearing in this document are
trademarks or registered trademarks of
their respective owners. Further, the ™or
®symbols are not used in the text.
Inhaltsverzeichnis
Sprachen:
Andere Sony Monitor Handbücher
Sony
Sony SDM-G76X Bedienungsanleitung
Sony
Sony LUMA LMD-4420 Bedienungsanleitung
Sony
Sony SCPH-152 b Bedienungsanleitung
Sony
Sony GDM-20SE2T - 20" CRT Display Bedienungsanleitung
Sony
Sony SDM-X52 - DELUXEPRO - 15" LCD Monitor Bedienungsanleitung
Sony
Sony LMD-4250W Bedienungsanleitung
Sony
Sony SDM-X52 - DELUXEPRO - 15" LCD Monitor Bedienungsanleitung
Sony
Sony SDM-HS73 Bedienungsanleitung
Sony
Sony MD-4251TD Bedienungsanleitung
Sony
Sony Trinitron CPD-E215E Bedienungsanleitung
Sony
Sony HMM-3000MT Bedienungsanleitung
Sony
Sony Trinitron CPD-E230 Bedienungsanleitung
Sony
Sony SDM-HS73 Bedienungsanleitung
Sony
Sony BRAVIA FW-50EZ20L Bedienungsanleitung
Sony
Sony BVME250A Bedienungsanleitung
Sony
Sony Multiscan CPD-G400 Installationsanleitung
Sony
Sony BRAVIA FW-85BZ35F Bedienungsanleitung
Sony
Sony TRINITRON VAIO CDP-220AS Bedienungsanleitung
Sony
Sony TRINITRON BVM-8045QD Bedienungsanleitung
Sony
Sony Trimaster PVM-X300 Bedienungsanleitung
