Sony UP-TX1 Series Installations- und Betriebshandbuch

3-197-011-11 (1)

Printer Driver

Installation Guide

This guide describes installation and use of the printer driver

for Windows XP and Windows 2000.

Before using the printer driver, be sure to read the “ReadMe”

file located on the CD-ROM.

Before Using this Software

UP-TX1 Series

Table of Contents 2

Windows 2000

Table of Contents

Operating Environment Requirements ................3

About This Document ............................................3

Installing the Printer Driver .................................4

Before Installation ..............................................4

Printer Driver Installation Under

Windows XP .......................................................5

Printer Driver Installation Under

Windows 2000 ....................................................6

Uninstalling the Printer Driver .............................8

Configuring the Printer .........................................9

[Paper] Tab ..........................................................9

[Graphics] Tab ..................................................10

Microsoft and Windows are registered trademarks of

Microsoft Corporation.

Other company names and product names mentioned in

this guide are also trademarks and registered

trademarks.

Operating Environment Requirements / About This Document 3

Windows 2000

Operating Environment

Requirements

The system requirements for use of the printer driver are

as follows:

• Computer running Microsoft Windows XP

Professional/Home Edition

• Computer running Microsoft Windows 2000

Professional

About USB 2.0

• The UP-TX1 series conforms to USB 2.0

specifications.

• USB 2.0 is fully backward compatible with USB 1.1.

• USB 2.0 supports conventional Full (low) speed and

Hi-Speed operation.

• In a USB 1.1 environment, connection and operation

at Full speed is possible. For Hi-Speed operation, the

following requirements must be met:

– Computer

Computer supporting Hi-Speed USB (USB 2.0

compliant)*

– Operating system

Microsoft Windows 2000 Professional/Microsoft

Windows XP Professional/Windows XP Home

Edition

– USB 2.0 driver

USB 2.0 device driver produced by Microsoft

Corporation (Operation with other USB 2.0 drivers

is not guaranteed.)

– Certified USB 2.0 cable

* Compatibility with all USB 2.0 devices, USB 2.0

expansion boards, or expansion cards cannot be

guaranteed.

Note

When the UP-TX1 series printer is connected and turned

on, ensure that the computer does not go into standby

(suspended) or hibernation mode. Otherwise correct

operation is not assured.

About This Document

The explanation of Control Panel operations in this

document assumes that Windows XP is used in Classic

View. To switch to Classic View, click [Start], select

[Control Panel], and click [Switch to Classic View] in

the Control Panel Properties shown on the left side of the

screen.

The screen messages and other information shown in the

section “Printer Driver Installation Under Windows XP”

assume connection of the UP-TX1. If another printer

model from the UP-TX1 series is connected, read any

occurrence of “UP-TX1” as the model name of your

printer.

Installing the Printer Driver 4

Windows 2000

Installing the Printer

Driver

Before Installation

About version upgrades

If you are upgrading a printer driver, remove the

previous printer driver before beginning the installation.

For details on the procedure to remove the printer driver,

refer to the section “Uninstalling the Printer Driver” in

this guide.

If the installation fails or is cancelled, restart your

computer before attempting the installation again.

Note

Be sure to restart your computer after installing or

uninstalling the printer driver. Unless you reboot,

unstable operation may result.

USB 2.0 connection

The UP-TX1 series is compatible with USB 2.0.

However, if your computer or USB hub is not USB 2.0-

compliant, the following message appears when you

connect the UP-TX1 series printer. Click to close the

message.

About Driver Signing Options

The present printer driver has not passed Windows Logo

testing, therefore when you install the driver an error

message may appear, preventing you from installing the

driver.

In the [Driver Signing Options] dialog box, select

[Ignore] or [Warn] in the [What action do you want

Windows to take?] group box. If you select [Block], you

cannot install the printer driver.

Open the [Driver Signing Options] dialog box as

follows:

1On the [Start] menu, click [Control Panel].

(Under Windows 2000, click [Start], select

[Settings], and click [Control Panel].)

2Double-click [System].

The [System Properties] dialog box opens.

3Click the [Hardware] tab.

4Click the [Driver Signing] button.

All the explanations in this guide assume that the setting

in this dialog box is [Warn].

Connecting multiple printers

When several UP-TX1 series printers are connected to a

computer running Windows XP, install the printer driver

for each printer according to the explanation in “Printer

Driver Installation Under Windows XP.”

When using Windows 2000, you can simply connect the

second and subsequent printers, and installation will be

carried out automatically.

Note

For installation of subsequent printers, install each

printer separately.

Installing the Printer Driver 5

Windows 2000

Printer Driver Installation Under

Windows XP

Connect the UP-TX1 series printer (one only) for

which the driver is to be installed to the computer.

Turn power to the connected UP-TX1 series printer

on.

Turn power to the computer on, and log on as the

system administrator or a member of the

Administrators group.

The [Found New Hardware Wizard] appears.

• If the [Found New Hardware Wizard] screen

looks like that shown in step 3, proceed to step 4.

• If the [Found New Hardware Wizard] screen

looks different from that shown in step 3, proceed

to step 5.

• If the [Found New Hardware Wizard] screen does

not appear, perform the steps described below,

with the UP-TX1 series printer for which the

printer driver is to be installed turned on and

connected to the computer. (Any other USB

printers or previously installed UP-TX1 series

printers should not be connected at this time.)

1Click [Start] and select [Control Panel].

2Double-click [System].

The [System Properties] dialog box opens.

3Click the [Hardware] tab.

4Click [Device Manager].

The [Device Manager] window opens.

5Click [+] at the left of [Universal Serial Bus

controllers].

6Right-click [USB Printing Support], and open

the Properties. Confirm that [UP-TX1] is

selected for [Location], and then select

[Uninstall] from the [Action] menu.

7Restart the computer.

The [Found New Hardware Wizard] appears.

Click [No, not this time] and click [Next].

Select [Install from a list or specific location

(Advanced)], and then click [Next].

The screen changes as follows.

Select [Search for the best driver in these locations],

select [Search removable media (floppy,

CD-ROM)], and then insert the supplied CD-ROM

“PRINTER DRIVER & INSTRUCTIONS FOR

USE UP-TX1” into the CD-ROM drive.

Click [Next].

The following dialog box appears.

Installing the Printer Driver 6

Windows 2000

Click [Continue Anyway].

After the files are copied, the following screen

appears.

Click [Finish].

Restart the computer.

This completes the installation of the printer driver.

Printer Driver Installation Under

Windows 2000

Connect the UP-TX1 series printer (one only) for

which the driver is to be installed to the computer.

Turn power to the connected UP-TX1 series printer

on.

Turn power to the computer on, and log on as the

system administrator or a member of the

Administrators group.

The [Found New Hardware Wizard] appears.

If the [Found New Hardware Wizard] does

not appear

Perform the steps described below, with the UP-

TX1 series printer for which the printer driver is to

be installed turned on and connected to the

computer. (Any other USB printers or previously

installed UP-TX1 series printers should not be

connected at this time.)

1Click [Start], select [Settings], and select

[Control Panel].

2Double-click [System].

The [System Properties] window opens.

3Click the [Hardware] tab.

4Click [Device Manager].

The [Device Manager] window opens.

5Click [+] at the left of [Universal Serial Bus

controllers].

6Right-click [USB Printing Support], and open

the Properties. Confirm that [UP-TX1] is

selected for [Location], and then select

[Uninstall] from the [Action] menu.

7Restart the computer.

The [Found New Hardware Wizard] appears.

Click [Next].

The screen changes as follows.

Installing the Printer Driver 7

Windows 2000

Select [Search for a suitable driver for my device

(recommended)] and then click [Next].

The screen changes as follows.

Select [CD-ROM drives], and then insert the

supplied CD-ROM “PRINTER DRIVER &

INSTRUCTIONS FOR USE UP-TX1” into the

CD-ROM drive.

Click [Next].

The screen changes as follows.

Click [Next].

If the [Digital Signature Not Found] dialog box

appears, click [Yes].

The screen changes as follows.

Click [Finish].

Restart the computer.

This completes the installation of the printer driver.

Note

If you select [Cancel] in step 7or [No] in step 8, the

[Found New Hardware Wizard] may not appear during

the next installation. In that case, perform the procedure

described in the section “If the [Found New Hardware

Wizard] does not appear” of step 3.

Uninstalling the Printer Driver 8

Windows 2000

Uninstalling the Printer

Driver

This section describes how to remove the printer driver.

Notes

• When starting the uninstallation procedure, the printer

should not be connected to the computer. If the [Found

New Hardware Wizard] screen appears, disconnect

the cable between the computer and printer, click

[Cancel] on all screens to terminate the wizard, and

then start the uninstallation procedure once more.

• If the uninstallation procedure is carried out with

multiple instances of the printer driver installed, all

drivers for UP-TX1 series printers (printer icons) will

be uninstalled.

Turn power to the UP-TX1 series printer off and

disconnect the cable between the computer and

printer.

Turn power to the computer on, and log on as the

system administrator or a member of the

Administrators group.

Click [Start] and select [Control Panel]. Then select

[Add or Remove Programs]. (Under Windows

2000, click [Start], select [Settings], and click

[Control Panel]. Then select [Add/Remove

Programs].)

From [Currently installed programs], select [Sony

UP-TX1 Series Printer Driver], and then click

[Change/Remove].

The following dialog box appears.

Click [Yes].

When the printer driver has been uninstalled, the

following dialog box appears.

Click [Yes].

The computer restarts.

This completes the printer driver uninstallation

procedure.

Configuring the Printer 9

Windows 2000

Configuring the Printer

Before printing from an application, you should make

the required printer properties settings.

To call up the printer properties window, use one of the

following methods:

• Click [Start] and then [Control Panel]. Select [Printers

and Faxes]. (Under Windows 2000, click [Start],

select [Settings], and click [Printers].) Select the Sony

UP-TX1 series printer icon, then click [Printing

Preferences] on the [File] menu. Settings made in this

way are used as default settings when printing from

applications.

• On the [File] menu of your application, click the item

for making printer settings. Settings made in this way

only remain valid until you close the application.

This section describes the settings available under the

tabs in [UP-TX1 Series Printing Preferences].

The explanation uses the screens as they appear in

Windows XP. Setting items and setting procedures are

the same in Windows 2000.

[Paper] Tab

This tab is used for making basic printing settings.

Paper Type

The relation between the type of paper that can be

inserted in the printer and the maximum print size is as

follows.

Orientation

Select [Portrait] or [Landscape].

Copies

Select the number of copies.

The setting range is 1 to 100 copies.

Scale

Lets you enlarge or reduce the image for printing. The

setting range is 10% to 400%, specified as a numeric

value.

About...

Brings up information about the printer driver version.

Restore Defaults

This returns all [Paper] tab settings to their default

condition.

Paper Type Maximum print size

(with landscape orientation)

UPC-T14 Series 1,848 ×1,248 (pixels)

Configuring the Printer 10

Windows 2000

[Graphics] Tab

This tab is used for making color, brightness, and other

image related settings. From the [Color Adjust] combo

box, you can select [Color Balance], or [Lightness], and

make the respective settings.

Color Balance

Select [Color Balance] from the [Color Adjust] combo

box.

Adjust the items by moving the respective sliders left or

right. You can also directly enter values in the input

fields.

Lightness

Select [Lightness] from the [Color Adjust] combo box.

Adjust the items by moving the respective sliders left or

right. You can also directly enter values in the input

fields.

Restore Defaults

This returns all [Graphics] tab settings to their default

condition.

Andere Handbücher für UP-TX1 Series

Inhaltsverzeichnis

Andere Sony Drucker Handbücher

Sony

Sony UP-DR100 Bedienungsanleitung

Sony

Sony UP55MD Bedienungsanleitung

Sony

Sony UPD-X100 Bedienungsanleitung

Sony

Sony DPP-EX50 Bedienungsanleitung

Sony

Sony UP-20 Bedienungsanleitung

Sony

Sony UP-20 Bedienungsanleitung

Sony

Sony DPP-SV55 Bedienungsanleitung

Sony

Sony DPP-M55 Marketing Bedienungsanleitung

Sony

Sony UP-CX1 series Bedienungsanleitung

Sony

Sony DPP-MS300 Marketing Bedienungsanleitung

Sony

Sony UP-CX2 Bedienungsanleitung

Sony

Sony UP-D890 Bedienungsanleitung

Sony

Sony UP-D75MD Bedienungsanleitung

Sony

Sony DPP-FP65 Bedienungsanleitung

Sony

Sony UP-D23MD Bedienungsanleitung

Sony

Sony UPX-C200 Bedienungsanleitung

Sony

Sony DPP-FP65 Bedienungsanleitung

Sony

Sony DPP-SV55 Kurzanleitung

Sony

Sony UP-D75 Bedienungsanleitung

Sony

Sony S-Frame DPP-F800 Handbuch

Sony

Sony SnapLab Bedienungsanleitung

Sony

Sony UP-CR25L Bedienungsanleitung

Sony

Sony DPP-FP50 Fall 2005 Bedienungsanleitung

Sony

Sony DPP-FP97 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung