Sony PCMD1 - Professional XLR Microphone Preamp Bedienungsanleitung

SERVICE MANUAL

Sony Corporation

Connect Company

Published by Sony Engineering Corporation

US Model

LINEAR PCM RECORDER

9-879-961-01

2005L04-1

Ver. 1.0 2005.12

SPECIFICATIONS

PCM-D1

– Continued on next page –

Recording media

Built-in flash memory 4 GB, “Memory Stick PRO (High Speed)”

(not supplied), Stereo recording

Maximum recordable time (Approximate)

The total maximum recordable time (approximate) of all the folders is as follows.

Built-in flash memory (4 GB)

Sampling frequency/ Maximum

quantifying bit number recordable time *

22.05 kHz 16 bit 13 hrs 10 min.

44.10 kHz 16 bit 6 hrs 35 min.

44.10 kHz 24 bit 4 hrs 20 min.

48.00 kHz 16 bit 6 hrs

48.00 kHz 24 bit 4 hrs

96.00 kHz 16 bit 3 hrs

96.00 kHz 24 bit 2 hrs

“Memory Stick PRO (High Speed)”

Sampling frequency/ Maximum recordable time *

quantifying bit number 256 MB 512 MB 1 GB 2 GB 4 GB

22.05 kHz 16 bit 45 min. 1 hr 30 min. 3 hrs 5 min. 6 hrs 25 min. 12 hrs 45 min.

44.10 kHz 16 bit 20 min. 45 min. 1 hr 30 min. 3 hrs 10 min. 6 hrs 20 min.

44.10 kHz 24 bit 15 min. 30 min. 1 hr 2 hrs 5 min. 4 hrs 15 min.

48.00 kHz 16 bit 20 min. 40 min. 1 hr 25 min. 2 hrs 55 min. 5 hrs 50 min.

48.00 kHz 24 bit 10 min. 25 min. 55 min. 1 hr 55 min. 3 hrs 50 min.

96.00 kHz 16 bit 10 min. 20 min. 40 min. 1 hr 25 min. 2 hrs 55 min.

96.00 kHz 24 bit 5 min. 10 min. 25 min. 55 min. 1 hr 55 min.

* The maximum recordable time is varied depending on recording condition.

PCM-D1

Quantization

16-bit linear, 24-bit linear

Frequency range (Input from the LINE IN jack

when recording/playing back) (0 to –2 dB)

Fs 22.05 kHz: 20 to 10,000 Hz

Fs 44.10 kHz: 20 to 20,000 Hz

Fs 48.00 kHz: 20 to 22,000 Hz

Fs 96.00 kHz: 20 to 44,000 Hz

Signal-to-noise ratio (S/N)

96 dB or above (1 kHz IHF-A)

(for 24 bit)

Total harmonic distortion (Input from the

LINE IN jack)

22.05 kHz 16 bit, 44.10 kHz 16/24 bit:

0.008% or below (1 kHz, 22 kHz LPF)

48.00 kHz 16/24 bit, 96.00 kHz

16/24 bit: 0.008% or below (1 kHz,

22 kHz LPF)

Wow and flutter

Below measurable limit (less than

±0.001% W.PEAK)

Input/output

MIC jack (stereo mini jack)

Input impedance: 22kΩ

Rated input level: 2.5mV

Minimum input level: 0.7mV

i(headphone) jack (stereo mini jack)

Rated output level: 400mV

Maximum output level: 30mW +

30mW or more

Load impedance: 16Ω

LINE IN jack

Input impedance: 47kΩ

Rated input level: 2.0V

Minimum input level: 570mV

LINE OUT/optical DIGITAL OUT jack

Output impedance: 220Ω

Rated output level: 1.8V

Load impedance: 22kΩ

Output level: –21 to –15dBm

(for optical digital output)

Emission wavelength: 630 to 690 nm

(for optical digital output)

DC IN 6V jack

USB connector (Hi-speed USB, Mass

Storage Class)

Memory Stick slot

General

Power requirements

DC IN 6V (AC 120V, 60 Hz)

Four size AA (LR06) nickel metal

hydride rechargeable batteries NH-AA

(supplied)

Four size AA (LR06) alkaline batteries

(not supplied)

Power consumption

2.1W

Dimensions

Approx. 72.0 ×193.0 ×32.7 mm

(27/8 ×63/4 ×15/16) (w/h/d) (not

including projecting parts and

controls)

Mass 525 g (18.52 oz) (including batteries)

Supplied accessories

•Windscreen

•AC power adaptor (6V)

•USB cable

•Carrying case

For carrying the recorder and the tripod

(not supplied).

•Wrist strap

•Charging set

(Battery charger BCG-34HRE, four size AA

(LR06) nickel metal hydride rechargeable

batteries NH-AA)

•Size AA (LR06) battery case

•CD-ROM

(“DigiOnSound5”*, “DigiOnAudio2

(trial version)”*, “Driver for Windows

2000”)

* For instructions, refer to the help function

of each application.

•Operating Instructions (this book)

Optional accessories

“Memory Stick PRO (High Speed)”

MSX-1GN (1 GB), MSX-2GN (2 GB),

MSX-4GN (4 GB)

“Memory Stick PRO Duo (High Speed)”

MSX-M1GN (1 GB),

MSX-M2GN (2 GB)

Stereo headphones

MDR-V900, MDR-V700DJ

Audio connecting cable

RK-G129

Optical digital cable

POC-N120B (optical mini plug y

optical mini plug)

POC-N120AB (optical mini plug y

rectangular-shaped optical plug)

External microphone

ECM-MS957

Design and specifications are subject to change

without notice.

PCM-D1

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE

WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN

THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE

PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR

IN SUPPLEMENTS PUBLISHED BY SONY.

Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270˚C during

repairing.

•Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering or

unsoldering.

Notes on Chip Component Replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be damaged

by heat.

•UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350°C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

PCM-D1

TABLE OF CONTENTS

1. GENERAL ................................................................... 5

2. DISASSEMBLY

2-1. Panel (Front) Block Assy ................................................ 10

2-2. Power Board .................................................................... 10

2-3. Meter (VU) ...................................................................... 11

2-4. VOL Block Assy .............................................................. 11

2-5. Audio (D/A) Board .......................................................... 12

2-6. Audio (A/D) Board .......................................................... 12

2-7. LCD Block Assy .............................................................. 13

2-8. Main Board ...................................................................... 13

2-9. Case (MIC-F) .................................................................. 14

2-10. MIC Block Assy .............................................................. 14

2-11. Microphone Unit (R) ....................................................... 15

2-12. Microphone Unit (L) ....................................................... 15

3. TEST MODE ............................................................... 16

4. ELECTRICAL ADJUSTMENTS .......................... 18

5. DIAGRAMS

5-1. Block Diagram – Audio A/D Section – ........................... 21

5-2. Block Diagram – Audio D/A Section – ........................... 22

5-3. Block Diagram – Power Section – .................................. 23

5-4. Printed Wiring Board – Audio A/D Section – ................. 24

5-5. Schematic Diagram – Audio A/D Section (1/2) – ........... 26

5-6. Schematic Diagram – Audio A/D Section (2/2) – ........... 27

5-7. Printed Wiring Board – Audio D/A Section – ................. 28

5-8. Printed Wiring Boards

– REC/HP VOL Flexible Section (VOL Block Assy) – .. 30

5-9. Schematic Diagram – Audio D/A Section – .................... 31

5-10. Printed Wiring Board – Main Section – .......................... 32

5-11. Schematic Diagram – Main Section (1/6) – .................... 34

5-12. Schematic Diagram – Main Section (2/6) – .................... 35

5-13. Schematic Diagram – Main Section (3/6) – .................... 36

5-14. Schematic Diagram – Main Section (4/6) – .................... 37

5-15. Schematic Diagram – Main Section (5/6) – .................... 38

5-16. Schematic Diagram – Main Section (6/6) – .................... 39

5-17. Printed Wiring Board – Power Section – ........................ 40

5-18. Schematic Diagram – Power Section – ........................... 42

6. EXPLODED VIEWS

6-1. Front Panel Section ......................................................... 47

6-2. LCD Section .................................................................... 48

6-3. VOL Section .................................................................... 49

6-4. Audio (A/D) Board, Audio (D/A) Board Section ............ 50

6-5. Main Board Section ......................................................... 51

6-6. MIC Section .................................................................... 52

6-7. Rear Panel Section ........................................................... 53

7. ELECTRICAL PARTS LIST .................................. 54

PCM-D1

SECTION 1

GENERAL This section is extracted

from instruction manual.

Identifying parts and controls

Front Right side

Overview (continued)

PCM-D1

1Built-in microphones (page 22)

2Analog level meters (page 25)

Displays left and right volume levels of an

audio signal input from microphones in

analog values.

3Display (page 16)

4VOLUME dial

Adjusts the playback volume when turned in

+/– directions.

>FF (fast-forward) /UP button

(pages 21, 29)

6MENU button (page 34)

7LIGHT button

Turns on or off the backlight of the display

and the analog level meters.

.FR (fast-rewind) /DOWN button

XPAUSE button/indicator (pages 25, 29)

(pages 21, 29)

9REC LEVEL L/R (recording level left/right)

dials (page 24)

0DISPLAY button (page 17)

Switches time information in the display.

qs ACCESS indicator (pages 20, 38)

Flashes when accessing memory (except

during recording).

zREC (recording) button/indicator

(page 24)

qf DIVIDE button (page 30)

NPLAY/ENTER button/indicator

(pages 21, 28)

xSTOP button (pages 25, 29)

qj MIC (microphone) jack (page 27)

qk i(headphone) jack (pages 26, 28)

ql MIC (microphone) /LINE IN switch

(page 24)

When set to “MIC,” records an audio signal

input from the built-in microphones or an

external microphone that is connected to the

MIC jack. When set to “LINE IN,” records an

audio signal output from external equipment

that is connected to the LINE IN jack.

w; Memory Stick slot (page 38)

wa POWER switch

Turns on or off the power.

ws Battery compartment lid (page 19)

wd Slit for a wrist strap (page 18)

Continued on the next page

Overview

PCM-D1

Left side

Overview (continued)

Display

7890

qa qs qd qf qg qjqh

PCM-D1

1LINE OUT/optical DIGITAL OUT jack

(page 29)

2LINE IN jack (page 27)

3MIC ATT (microphone attenuator) switch

(page 23)

4USB connector (page 30)

5DC IN 6V jack (page 20)

6HOLD switch

When set to “ON,” the buttons on the

recorder are locked to prevent accidental

operation. It is recommended to set to “ON”

during recording and playback. To unlock

the controls, set to “OFF.”

7Time information

Each time the DISPLAY button is pressed,

the time information changes as follows

(Flashes when the recorder is paused):

Elapsed recording/playback time

8Recording/playing status

Displays as follows according to the current

operation:

Recording

(Flashing) Recording pause,

standby for recording

Playback

(Flashing) Playback pause

Stop

Go to previous/succeeding

tracks

Peak meter (page 25)

Memory Stick indicator

Displayed when the current memory is a

“Memory Stick PRO (High Speed).”

Folder number, track numbers

Track numbers are displayed as “current

track number/total numbers of tracks.”

Sampling frequency and quantifying bit

number of currently recording/playing

track (page 35)

HPF (High Pass Filter) setting

Displayed when “200Hz HPF” is set to “ON”

(page 36).

Limiter setting

Displayed when “LIMITER” is set to “ON”

(page 35).

Remaining memory volume

Displayed the remainig volume of current

memory (page 26).

File name of currently recording/playing

track

Remaining battery power (page 20)

Overview

Fast reverse/forward

Recorded date

(During recording: Recording start date)

Remaining recordable time of the current

memory (During playback: Remaining

time of the current track)

PCM-D1

SECTION 2

DISASSEMBLY

Note: This set can be disassemble according to the following sequence.

2-1. PANEL (FRONT) BLOCK ASSY

(Page 10)

2-2. POWER BOARD

(Page 10)

2-3. METER (VU)

(Page 11)

2-5. AUDIO (D/A) BOARD

(Page 12)

2-6. AUDIO (A/D) BOARD

(Page 12)

2-7. LCD BLOCK ASSY

(Page 13)

2-8. MAIN BOARD

(Page 13)

2-4. VOL BLOCK ASSY

(Page 11)

2-9. CASE (MIC-F)

(Page 14)

2-10. MIC BLOCK ASSY

(Page 14)

2-11. MICROPHONE UNIT (R)

(Page 15)

2-12. MICROPHONE UNIT (L)

(Page 15)

SET

PCM-D1

2-2. POWER BOARD

Note: Follow the disassembly procedure in the numerical order given.

2-1. PANEL (FRONT) BLOCK ASSY

two

screws

(M1.7)

two

screws

(M1.7)

two cushions (panel)

panel (front) block assy

two

screws

(P2 (M1.7))

two

screws

(P2 (M1.7))

screw

(P2 (M1.7))

screw

(P2 (M1.7))

LCD back light unit (5 core)

(CN1503)

LCD block assy

POWER FLEXIBLE board (20 core)

(CN1501)

SIG FLEXIBLE board (24 core)

(CN1502)

Remove the ten solders.

POWER board

Andere Handbücher für PCMD1 - Professional XLR Microphone Preamp

Inhaltsverzeichnis

Andere Sony Aufnahmegeräte Handbücher

Sony

Sony XPERIA SmartTags NT2 Bedienungsanleitung

Sony

Sony DMX-R100 Bedienungsanleitung

Sony

Sony PWSK-4504 Bedienungsanleitung

Sony

Sony RCDW500C - Compact Disc Player Bedienungsanleitung

Sony

Sony SEQ-421 Bedienungsanleitung

Sony

Sony PCM-800 Bedienungsanleitung

Sony

Sony BZDM-7020 Bedienungsanleitung

Sony

Sony RCD-W2000ES - Cd/cdr Recorder Bedienungsanleitung

Sony

Sony IFB-40 Bedienungsanleitung

Sony

Sony DPS-V55 Bedienungsanleitung

Sony

Sony PCM-3348HR Bedienungsanleitung

Sony

Sony TCM-4300 Bedienungsanleitung

Sony

Sony XDCAM PDW-HD1500 Bedienungsanleitung

Sony

Sony TC-765 Bedienungsanleitung

Sony

Sony SB-3335 Bedienungsanleitung

Sony

Sony PMW50 Bedienungsanleitung

Sony

Sony SEG-2550 Bedienungsanleitung

Sony

Sony SB-V66S Bedienungsanleitung

Sony

Sony FXE-120; FXE-120-P Bedienungsanleitung

Sony

Sony DFR-E3000 Bedienungsanleitung

Sony

Sony HSR-J2009 Bedienungsanleitung

Sony

Sony MU-R201 Bedienungsanleitung

Sony

Sony WX-C55 Bedienungsanleitung

Sony

Sony DMX-R100 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch