Sony PFV-L02 Bedienungsanleitung

INTERFACE UNIT

PFV-L02

INSTALLATION MANUAL

1st Edition

Serial No. 10001 and Higher

PFV-L02

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

For the U.S.A

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

WARNING

This unit has no power switch.

When installing the unit, incorporate a readily

accessible disconnect device in the fixed wiring, or

connect the power cord to a socket-outlet which must be

provided near the unit and easily accessible, so that the

user can turn off the power in case a fault should occur.

WARNUNG

Dieses Gerät hat keinen Netzschalter.

Beim Einbau des Geräts ist daher im Festkabel ein

leicht zugänglicher Unterbrecher einzufügen, oder das

Netzkabel mu

mit einer in der Nähe des Geräts

befindlichen, leicht zugänglichen Wandsteckdose

verbunden werden, damit sich bei einer

Funktionsstörung die Stromversorgung zum Gerät

jederzeit unterbrechen lä

1 (E)

PFV-L02

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 2 (E)

Related manuals................................................................................................... 2 (E)

1. Installation

1-1. Operating Environment .........................................................................1-1 (E)

1-2. Supplied Accessories ............................................................................1-1 (E)

1-3. Power Supply ........................................................................................1-1 (E)

1-3-1. AC Power Supply.................................................................1-1 (E)

1-3-2. DC Power Supply.................................................................1-1 (E)

1-4. Installation Space ..................................................................................1-2 (E)

1-5. Installing Optional Board ......................................................................1-3 (E)

1-6. Handle ...................................................................................................1-4 (E)

1-7. Installing Battery Adaptor.....................................................................1-4 (E)

1-8. Rack Mounting......................................................................................1-4 (E)

1-8-1. Notes on Rack Mounting .....................................................1-4 (E)

1-8-2. Joining Two PFV-L02s ........................................................1-5 (E)

1-8-3. Rack Mounting Procedure....................................................1-5 (E)

2 (E) PFV-L02

Purpose of this manual This manual is the installation manual of Interface Unit PFV-L02.

This manual is intended for use by trained system and service engineers, and

describes the information for installation of the unit.

Related manuals The following manuals are prepared for PFV-L02.

.Operation Manual (Supplied with PFV-L02)

This manual describes the notes on operating, the locations and functions of parts,

and controls of PFV-L02.

.Maintenance Manual (Available on request)

This manual describes the information for periodic maintenance and detailed

service.

If this manual is required, please contact your local Sony Sales Office/Service

Center.

.“Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in Communication System Solutions Network Company

equipment.

Semiconductors that cannot be searched for on this CD-ROM are listed in the

service manual for the corresponding unit. The service manual contains a com-

plete list of all semiconductors and their ID Nos., and thus should be used together

with the CD-ROM.

Part number: 9-968-546-XX

Manual Structure

1-1 (E)

PFV-L02

Section 1

Installation

1-1. Operating Environment

Operating temperature 5 dC to 40 dC

Performance temperature 10 dC to 35 dC

Humidity 10 to 90 % (No condensation)

Weight Approx. 2.3 kg

(Except the joined-unit and the optional unit and board)

.To prevent overheating of PFV-L02, ensure that there is

good air circulation around the unit.

.Do not put the unit in a place subject to excessive lamp

smoke, vapor, moisture, or dust.

Install in a stable location.

Installation on unstable or tilting surface may cause the

unit fall off, resulting in injury.

1-2. Supplied Accessories

In the PFV-L02, the following parts used for the mounting

on a rack and the joining two PFV-L02 units are provided.

.Rack angle (Part No.: 3-203-661-02)..................... 2 pcs

.Joint bracket (Part No.: 3-204-705-02) .................. 1 pc

.Screws (B 4x5: 7-682-559-04) .............................. 8 pcs

.Screws (PS 3x6: 7-682-647-09) ............................ 2 pcs

1-3. Power Supply

1-3-1. AC Power Supply

Power voltage AC 100 V to AC 240 V

Power frequency 50 Hz or 60 Hz

Power consumption Max. 0.51 A

(With the optional boards installed)

Rush current AC 100 V IN : 16 A

AC 240 V IN : 20 A

The AC power supply requires a capacity which is

commensurate with rush current. If the capacity of the AC power

supply is not sufficient, the breaker of the AC power on the

supply side may operate or this unit may not operate normally.

Recommended Power Cord

For customers in U.S.A. and Canada

Required Parts

1Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11

For customers in the United Kingdom

Required Part

2Power cord, 250 V 10 A (2.5 m) : !1-782-929-11

For the customers outside of the area shown above, please

contact your local Sony Sales Office/Service Center.

.Use a specified power cord only.

Be sure to use a recommended power cord to avoid fire

and/or an electric shock.

.Ground the unit for your safety.

Be sure to attach a ground wire to avoid an electric shock.

1-3-2. DC Power Supply

Power voltage DC 12 V

Power consumption Max. 1.8 A

.The unit works either on the AC adaptor or battery.

When repairing or checking the unit, AC adaptor

operation is recommended.

.The AC adaptor AC-DN1 cannot be used to derive power.

.When the battery is nearly dead, the DC STATUS

indicator on the front panel will blink.

For more details, refer to the Operation Manual supplied

with the unit.

AC inlet

PFV-L02

1-2 (E)

1-4. Installation Space

Do not block the ventilation holes of the unit.

Both of the front and rear sides must be at least 20 cm away from the walls for ventilation and

maintenance.

The outer dimensions of PFV-L02 are as shown here:

1-4. Installation Space

Unit: mm

323.8

340

220

240

15.3

115.5

43.6

56.7

31.8

482

440

465

(During joint of two units)

1-3 (E)

PFV-L02

1-5. Installing Optional Board

The optional board can be installed in any empty slot of

PFV-L02.

Installing Main Board (Front side)

1. Loosen the two screws and remove the front panel.

2. Set the switch (S1) on the PS-607 board to OFF.

3. Insert the main board along the board guides with the

board lever closed in the direction of arrow 1shown

in the figure. Then, connect the main board securely

to the connector on the MB-932 board.

4. Install the front panel in the reverse procedure of steps

1 and 2.

When removing the main board, open the board lever in

the direction indicated by arrow 2and pull out the board

toward you.

Installing Connector Panel (Rear side)

The connector panel must be installed in the slot which

contains the main board.

1. After removing the two screws, remove the blank

panel of the slot which contains the main board.

Keep the blank panel which is removed.

1-5. Installing Optional Board

Screws

Front panel

PS-607 board

OFF

Main board

A side

Board lever

MB-932 board

Board guides

Main board

Board lever

Blank panel

B 2.6x4

PFV-L02

1-4 (E)

Specified rack mounting kit: RMM-10

PFV-L02 may not be able to be mounted on a 19-inch

standard rack using a rack mounting kit other than the

specified one.

Components of RMM-10

.Rack brackets ......................................................... 2 pcs

.Rack mounting adaptor (right) ............................... 1 pc

[Including two screws (B 4x6: 7-682-560-09)*]

.Rack mounting adaptor (left) ................................. 1 pc

[Including two screws (B 4x6: 7-682-560-09)*]

.Rack bracket fixing screws (B 4x6: 7-682-560-09)

........................................................................ 6 pcs

.Adaptor fixing screws (B 4x10: 7-682-560-10)

........................................................................ 6 pcs

*: These four screws (B4x6) are not used.

Required other parts

To mount the unit on the rack, the following parts are

required.

.Screws (RK 5x16: 7-682-378-04) ......................... 4 pcs

.Ornamental washers (2-297-913-01) ..................... 4 pcs

.Supplied accessories of PFV-L02 described in Section 1-

1-8-1. Notes on Rack Mounting

.Fix the rack on the horizontal and firm floor with bolts to

prevent it from turning over or moving.

If the rack overturn due to the weight of the unit, this

may cause a death or serious injury.

.Use the specified rack mounting kit.

If not, the unit may fall because of insufficient strength.

This causes an injury.

.After rack mounting, be sure to tighten the screws of the

rack angle and fix this unit to the rack.

If not, this unit may slide and fall from the rack. This

causes an injury.

Attention when this unit is installed in the rack:

.Be careful not to put your hand or finger in the rack

mounting rail.

.Install in a stable posture.

1-5. Installing Optional Board

1-6. Handle

1-7. Installing Battery Adaptor

1-8. Rack Mounting

2. Connect the connector panel to the connector on the

MB-932 board.

3. Secure the connector panel with the two screws

removed in step 1.

Do not open the slot for an air-cooling effect of this unit.

Attach the blank panel to an empty slot.

1-6. Handle

A handle can be installed on the left side panel of PFV-L02.

The following parts are required.

(They are not supplied accessories.)

.Handle (Part No.: 3-419-372-31) ........................... 1 pc

.Handle tables (Part No.: 2-253-306-31)................. 2 pcs

.Screws (K 4x14: 7-682-264-04)............................ 2 pcs

1-7. Installing Battery Adaptor

For the way to install the battery adaptor on this unit, refer

to the supplied Operation Manual.

1-8. Rack Mounting

The PFV-L02 can be mounted on a 19-inch standard rack

for use when two PFV-L02s are joined. Use the specified

rack mounting kit for the rack mounting.

For the way to join the PFV-L02s, refer to "1-8-2. Joining

Two PFV-L02s".

B 2.6x4

Connector panel

1-5 (E)

PFV-L02

Install a ventilating fan in the rack to prevent the increase

in the temperature inside a rack when multiple units are put

in one rack.

1-8-2. Joining Two PFV-L02s

After that, two units are described as “unit A” and “unit

B”.

1. Loosen the eight screws of units A and B, respectively,

then remove protectors (four each).

2. Remove the two stepped screws of unit B.

3. Install the rack angles outside units A and B with

supplied two screws (B 4x5) each.

(Refer to the next column, the upper figure.)

4. Insert the stepped screws of unit A into the joint holes

of unit B and slide unit B in the direction indicated by

the arrow.

At that time, confirm that the two units are joined

securely.

5. Remove the front panels of units A and B.

(Refer to Section 1-5.)

6. Install the joint bracket in units A and B and secure it

with two screws (PS 3x6).

Protectors

Unit A

Unit B

Stepped screw

7. Install the front panels of units A and B.

(Refer to Section 1-5.)

1-8-3. Rack Mounting Procedure

For the rack mounting, refer to the Installation Manual of

RMM-10.

Be sure to use the screws (B 4x5) supplied with the

PFV-L02 when securing the rack brackets. In this case, do

not use the screws (B 4x6) supplied with RMM-10. If not,

this may damage the boards in the unit.

B 4x5

PS 3x6

Rack angle

Joint bracket

Unit A

Joint holes

Stepped screws

Rack angle

Unit B

1-8. Rack Mounting

Rack bracket

B 4x5

Inhaltsverzeichnis

Andere Sony Aufnahmegeräte Handbücher

Sony

Sony RCD- W222ES Bedienungsanleitung

Sony

Sony ICD-B25 Operating Instructions (primary... Bedienungsanleitung

Sony

Sony SRW-1 Bedienungsanleitung

Sony

Sony SEQ-431 Bedienungsanleitung

Sony

Sony SEQ-V902 Bedienungsanleitung

Sony

Sony DMX-R100 Bedienungsanleitung

Sony

Sony TCD-D3 Bedienungsanleitung

Sony

Sony DEP-100 Bedienungsanleitung

Sony

Sony XDCAM PDW-HD1200 Bedienungsanleitung

Sony

Sony PFV-L10 Bedienungsanleitung

Sony

Sony PCM-R300 Bedienungsanleitung

Sony

Sony HAR-D1000 - Hard Disc Audio Recorder Bedienungsanleitung

Sony

Sony BVT-2000 Bedienungsanleitung

Sony

Sony RCD-W3 - Cd/cdr Recorder/player Bedienungsanleitung

Sony

Sony SRPC-1 Bedienungsanleitung

Sony

Sony NXL-IP55 Bedienungsanleitung

Sony

Sony IFB-12A Bedienungsanleitung

Sony

Sony HVO-500MD Montageanleitung

Sony

Sony CFD-S550 - Cd Radio Cassette-corder Bedienungsanleitung

Sony

Sony XDCAM PDW-HD1500 Bedienungsanleitung

Sony

Sony CDR-W33 Bedienungsanleitung

Sony

Sony HAR-D1000 - Hard Disc Audio Recorder Bedienungsanleitung

Sony

Sony CFD-RS60CP Bedienungsanleitung

Sony

Sony TC-366 Einrichtungshandbuch

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch