Sony RM-TP501 Bedienungsanleitung
3-864-784-11(1)
Remote
Commander
Operating Instructions
1998 by Sony Corporation
RM-TP501
2
Precautions
CAUTION (Lithium battery)
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Discard
used batteries according to the manufacturer’s
instructions.
On operation
Before connecting other components, be sure to turn off and
unplug the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth slightly
moistened with a mild detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent such as alcohol or
benzine.
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
About This Manual
• The following icon is used in this manual:
zIndicates hints and tips for making the task easier.
3
TABLE OF CONTENTS
Preparations 4
Compatible Components and Functions 4
Preparing the Commander 5
Screen Hierarchy 8
Location of Parts and Basic
Operations 9
Front panel 9
Rear panel 10
Operation 11
Basic Operations 11
Example: Operating a CD Player 13
Example: Operating the Tuner 14
Example: Recording from CD to MD 15
Selecting Sound Fields 16
Adjusting Sound Fields 17
Adjusting the Commander’s Operating
Environment 18
Additional information 22
Precautions during use 22
Troubleshooting 23
Specifications Back Cover
Index Back Cover
4
Preparations
This chapter describes how to prepare
the remote commander for operation.
Be sure to read this section before
operating.
Compatible Components
and Functions
This unit is a remote control system that utilizes infrared
rays to control a receiver and AV components connected
to the receiver.
Compatible Components
This unit can be used to operate Sony AV components as
well as AV components manufactured by other
manufacturers. Set up is necessary in order to operate
components manufactured by other companies (see page
18).
Functions
This unit is a bidirectional remote commander. Not only
does it transmit infrared rays for operation of the receiver,
it can also receive infrared rays emitted by the receiver to
display characters and other information supplied by
other components connected to the receiver with a
CONTROL A1 cord.
5
Preparations
Please be sure to carry out the procedures described in
“Setting up the commander” on page 6 after inserting the
batteries.
Inserting batteries into the commander
Insert the four size-AA (LR6) alkaline batteries (for
commander operation) and lithium battery (for
preservation of the commander’s internal memory).
1Remove the battery compartment cover.
2Insert the alkaline batteries.
3Insert the lithium battery.
After wiping the lithium battery thoroughly with a
dry cloth, insert it into the compartment with the
positive (+) pole side facing up.
Preparing the Commander
4Close the battery compartment cover.
After inserting the batteries, touching the touch panel
turns on the light and displays the touch panel (LCD)
adjustment screen. Follow the procedure on the next
page for touch panel adjustment and initial
communication.
Notes
• The LCD lights up when touched.
• VOL+/–, MUTING and SLEEP can be used even when the
LCD is not lit.
• Pressing BACK LIGHT/COMMANDER OFF turns the
backlight off. Holding it down for about 2 seconds turns the
LCD off. To conserve battery power, be sure to regularly turn
off the LCD or power when not in use.
• If the commander is not used for approx. 1 minute, the LCD
turns off automatically (Auto Off function). The auto off time
can be adjusted (see page 21).
Push in direction of
arrow
Always insert the negative (–) pole
side of batteries first.
Size-AA alkaline batteries
Coin shaped lithium
battery CR2032
Positive (+) pole side up
]
]
}
}
]
}
]
}
6
Preparations
Touch panel adjustment
3Adjust the position of the touch panel’s LCD.
Touch the center of each of the 4 dots with the touch
pen. When all 4 dots have been touched “Adjusted”
appears, a buzzer sounds, and the initial
communication screen appears.
Caution
Touch panel adjustment must be carried out for proper panel
operation. If used without adjustment, the ”Touch Panel
Adjustment” screen appears each time the LCD lights up.
Initial communication
4Press 1/u on the receiver to turn on the receiver.
5Point the commander’s transmitter/receiver section
toward the receiver’s display, and touch OK.
Once initial communication with the receiver has been
established, the commander is ready to operate the
receiver.
Setting up the commander
Please be sure to carry out the following 1 to 5 procedures
for preparation of the commander.
The commander’s panel is touch sensitive and can be
operated by simply touching it.
1Remove the touch pen.
When returning the touch pen, always slide it in tip
first.
Caution
Use only the touch pen provided with this unit or the soft tip
of your finger to operate the touch panel. Using a
commercially available writing utensils may damage the
panel and make correct operation impossible. If the tip of the
touch pen is damaged, or the touch pen is lost, please consult
your nearest Sony dealer.
2Turn CONTRAST to adjust brightness of the LCD.
Touch the 4 dots with the touch pen.
Preparing the Commander
Pen holder
Remove by sliding out
CONTRAST control
7
Preparations
Note
• To ensure good communication conditions, carry out initial
setup from directly in front of, and close to the receiver.
• Do not move the unit during initial setup.
If a communication error occurs during setup
An error message will be displayed.
• Touching OK will return to the step 5 setup screen.
• Touching SKIP goes to the regular screen without
carrying out initial setup. Although operation is
possible in this condition, functions not included on the
receiver will be displayed, and some buttons will not be
operable. Also, the initial setup screen will appear each
time the touch panel is turned on.
Note
The commander receives and displays data transmitted from the
receiver. Communication errors may occur if the commander’s
transmitter/receiver section is not directed properly toward the
receiver’s display.
Be sure to point the commander’s transmitter/receiver section
towards the receiver’s display.
When replacing the batteries
To ensure preservation of the commander’s internal
memory when replacing batteries, be sure to observe the
following cautions.
When to replace batteries
When the batteries become weak, a warning sounds and a
message is displayed. Replace batteries as instructed by
the message.
How to remove the lithium battery
Notes
• Disc titles and song titles downloaded from the CD changer are
memorized in the commander. The lithium battery is used for
preservation of this memory. If the unit is used with an
exhausted battery, the settings memorized in the commander
will be erased. Please replace the battery as soon as the message
appears.
• Replace the alkaline batteries with new batteries as soon as
their charge is exhausted. If the unit is used with exhausted
batteries, exhaustion of the lithium battery used to maintain
memory will be quickened and the memorized settings may be
erased.
• The life span of batteries may be shortened depending on the
conditions in which the commander is used.
• If the alkaline batteries and lithium battery become exhausted
at the same time, replace the alkaline batteries first. Replacing
the lithium battery first will erase the data memorized in the
commander.
• When replacing the alkaline batteries, always replace all 4
batteries with new ones.
• After replacing batteries, be sure to carry out touch panel
adjustment (page 6).
1 m ~ 2 m
Replace alkaline
batteries. Replace lithium
battery.
8
Preparations
The following diagram show the basic composition of this unit’s screen hierarchy.
FUNCTION screen
Screen Hierarchy
Normally, the
FUNCTION
screen is
displayed.
To display a
different screen,
touch the left side
of the LCD.
SOUND FIELD screen
SETUP screen
Screen for selection and
adjustment of the sound fields
(see page 16~18).
Screen for setting up the
operation environment and
control of components made by
other manufacturers (page 18).
Touch when the song titles of
a CD or MD being played
back are not displayed
correctly.
Screens for selection and
operation of components
connected to the receiver.
Screen for recording audio
and video from one
component to another (see
page 15).
RELOAD...
9
Location of Parts and Basic Operations
Front panel
1BACK LIGHT/COMMANDER OFF
Press to turn the backlight on or off. Hold down for
about 2 seconds to turn the LCD off. When the LCD is
off, press to turn on the LCD and backlight.
2Touch panel
Touch to operate. The commander turns on
automatically.
3VOL +/– buttons
Use to adjust the volume of the receiver.
4JOG DIAL control
Rotate to scroll through items in a list (etc.).
Push to select the highlighted item.
5SYSTEM/STANDBY button
Normally used to turn off all Sony components. Can
also be used to turn the receiver on or off depending
on the settings made in the SETUP screen (see page
21).
6MUTING button
Use to mute the sound of the receiver.
7CONTRAST control
Use to adjust the contrast of the LCD.
8SLEEP button
Use to operate the receiver’s sleep function. The sleep
settings appear in the receiver’s display, not the
commander’s LCD.
Location of
Parts and Basic
Operations
This chapter provides information
about the locations and functions of
the buttons and controls on this unit.
123
4
5
6
7
8
10
Location of Parts and Basic Operations
Rear panel
1Transmitter/receiver section
Transmits and receives infrared signals to and from
the receiver.
2Battery cover
3Touch pen
4SYSTEM/STANDBY button
Normally used to turn off all Sony components. Can
also be used to turn the receiver on or off depending
on the settings made in the SETUP screen (see page
21).
5Touch pen holder
Pull out and insert touch pen when not in use.
12
3
4
5
Andere Handbücher für RM-TP501
1
Inhaltsverzeichnis
Andere Sony Fernbedienung Handbücher
Sony
Sony RM-LP211 Bedienungsanleitung
Sony
Sony RM-TP502 Bedienungsanleitung
Sony
Sony Remote Commander RM-V22 Bedienungsanleitung
Sony
Sony RMF-YD003 Bedienungsanleitung
Sony
Sony RM-LG112 Bedienungsanleitung
Sony
Sony 3-097-863-13 Bedienungsanleitung
Sony
Sony RM-KZ1 Bedienungsanleitung
Sony
Sony RM-V301 Technisches Handbuch
Sony
Sony Ipela RM-NS10 Bedienungsanleitung
Sony
Sony RM-PP505 - Remote Control For Strde875 Bedienungsanleitung
Sony
Sony KV-29FC60A Bedienungsanleitung
Sony
Sony RMF-TX100U Bedienungsanleitung
Sony
Sony Remote Commander RM-V15 Bedienungsanleitung
Sony
Sony RM-MC60 Bedienungsanleitung
Sony
Sony RM-X12A Bedienungsanleitung
Sony
Sony RM-BR300 - Remote Control Unit Bedienungsanleitung
Sony
Sony rm-v8e Bedienungsanleitung
Sony
Sony MKS-8080 Bedienungsanleitung
Sony
Sony RM-V302 Bedienungsanleitung
Sony
Sony RM-V111T Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
