Sony NSS-V2 Bedienungsanleitung

INSTALLATION MANUAL

1st Edition (Revised 1)

MULTI-FORMAT MEDIA SERVER

NSS-V2

DIGITAL INPUT PROCESSOR BOARD

BKNS-V202

DIGITAL OUTPUT PROCESSOR BOARD

BKNS-V203

9PIN CONTROL INTERFACE BOARD

BKNS-V209

NSS-V2

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

NSS-V2 Serial No.10001 and Higher

BKNS-V202 Serial No.10001 and Higher

BKNS-V203 Serial No.10001 and Higher

BKNS-V209 Serial No.10001 and Higher

WARNING

This unit has no AC power switch.

When installing the unit, incorporate a readily

accessible disconnect device in the fixed wiring, or

connect the power cord to a socket-outlet which must

be provided near the unit and easily accessible, so that

the user can turn off the power in case a fault should

occur.

WARNUNG

Dieses Gerät hat keinen AC-Netzschalter.

Beim Einbau des Geräts ist daher im Festkabel ein

leicht zugänglicher Unterbrecher einzufügen, oder das

Netzkabel mu

mit einer in der Nähe des Geräts

befindlichen, leicht zugänglichen Wandsteckdose

verbunden werden, damit sich bei einer

Funktionsstörung die Stromversorgung zum Gerät

jederzeit unterbrechen lä

For safety, do not connect the connector for peripheral

device wiring that might have excessive voltage to the

following port(s).

: 100BASE-TX connector

Follow the instructions for the above port(s).

NSS-V2 1 (P)

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

5. Install the equipment while taking the operating

temperature of the equipment into consideration

For the operating temperature of the equipment, refer

to the specifications of the Operation Manual.

6. When performing the installation, keep the

following space away from walls in order to

obtain proper exhaust and radiation of heat.

Rear: 10 cm (4 inches) or more

Laser Diode Properties

Wave length : 850 nm

Emission duration : Continuous

Laser output power : 0.5 mW (max.) (Specification

of an optical pickup)

CAUTION

The use of optical instruments with this product

will increase eye hazard.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein

may result in hazardous radiation exposure.

This Multi-format Media Server is classified as a CLASS

1 LASER PRODUCT.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

NSS-V2

2 (P)

PRECAUTIONS

Use the specified power cord only

Use of power cords other than the specified ones may

cause fire or electric shock.

Do not damage the power cord

A damaged power cord may cause fire or electric shock.

When mounting the unit in a rack, be careful not to

catch the power cord in the rails.

Do not install the unit in humid or dusty locations

Dust, soot, and oil particles in the ambient atmosphere

may cause fire or electric shock.

Install the dedicated circuit breaker or power switch

This unit is not equipped with an AC power switch.

Install the dedicated circuit breaker or power switch,

and/or plug the power cord in the outlet.

Do not block the ventilation slots

If the ventilation slots are blocked, overheating inside

the unit may cause fire. Observe the following points to

ensure adequate ventilation.

.Do not install in narrow or sealed locations.

.Remove dust from the fan and air filter.

Install in a stable location

Installation in an unstable place may cause the unit fall,

resulting in injury.

Do not stack the units

Do not stack two or more units on top of each other.

Mount in a rack to avoid the risk of the unit sliding and

causing injury.

Ground the unit safely

Failure to ground the unit may cause electric shock.

Handling the unit by holding the designated

positions

When handling the unit, be sure to hold the following

positions.

Otherwise, the unit may break and fall, causing injury.

.Rack angle

.Bottom case

Especially, do not hold the front panel or the handle of

the power supply unit.

Carry the unit with more than two persons

The total weight of this unit is 21 kg.

Carrying the unit with less than two persons may cause

injury.

Mount with more than two persons

The total weight of this unit is 21 kg.

Mounting the unit with less than two persons may cause

injury.

Mount only with the specified rack mount rails

Rack mount rails other than those specified for this unit

may not be strong enough to support the unit, risking

possible collapse and injury.

Secure the unit to a rack with the screws

If the unit is not secured completely, this may cause the

unit fall off, resulting in injury. Be sure to secure the unit

with the screws when mounting to the rack. (Refer to

“1-4. Rack Mounting”)

Plug and connector of the power cord must be

inserted as far as they can go

Plug and connector of the power cord must be inserted

into the AC inlet as far as they can go.

1 (E)

NSS-V2

Table of Contents

Manual Structure

Purpose of this manual ........................................................... 3 (E)

Related manuals ..................................................................... 3 (E)

Contents .................................................................................. 3 (E)

Trademarks ............................................................................. 3 (E)

1. Installation

1-1. Installation Procedure .............................................. 1-1 (E)

1-2. Operating Conditions and Installation Space .......... 1-2 (E)

1-3. Power Supply ........................................................... 1-4 (E)

1-3-1. Information for Power Supply ........................ 1-4 (E)

1-3-2. Recommended Power Cord ............................ 1-4 (E)

1-4. Rack Mounting ........................................................ 1-5 (E)

1-5. Installing the Option Boards .................................... 1-7 (E)

1-5-1. Installing the BKNS-V202/V203 ................... 1-7 (E)

1-5-2. Installing the BKNS-V209 ............................. 1-8 (E)

1-6. Signal Input and Output ........................................... 1-9 (E)

1-7. Connecting Connectors and Cables ....................... 1-10 (E)

1-8. Connection ............................................................. 1-11 (E)

1-9. Setting after Installation ......................................... 1-12 (E)

2. Service Overview

2-1. Cleaning the Air Filter ............................................. 2-1 (E)

2-2. Functional Descriptions of Board Switches

and LEDs ................................................................. 2-2 (E)

2-2-1. FC-100 Board ................................................. 2-2 (E)

2-2-2. SY-318 Board ................................................. 2-3 (E)

2-2-3. TM-45 Board .................................................. 2-4 (E)

2-2-4. MPU-136 Board ............................................. 2-5 (E)

2-2-5. ENC-90 Board (BKNS-V202) ....................... 2-6 (E)

2-2-6. DEC-154 Board (BKNS-V203) ..................... 2-7 (E)

2-2-7. IF-972 Board (BKNS-V209) .......................... 2-8 (E)

2-3. Operating Setup Tool ............................................... 2-9 (E)

2-3-1. Setup Tool Descriptions ............................... 2-10 (E)

2-3-2. Changing Setup Table .................................. 2-11 (E)

2-3-3. Changing the Setup Values using

Dynamic Setup ............................................. 2-12 (E)

2-4. Building File Manager-PC ..................................... 2-18 (E)

2-4-1. Preparation ................................................... 2-18 (E)

2-4-2. Installation .................................................... 2-19 (E)

2-4-3. Others ........................................................... 2-19 (E)

2-5. Installing Transfer Manager .................................. 2-22 (E)

2-5-1. Preparation ................................................... 2-22 (E)

2-5-2. Installation .................................................... 2-22 (E)

2-5-3. Startup/Stop .................................................. 2-29 (E)

2-6. Setting McDATA FC Switch ................................. 2-31 (E)

2-6-1. Preparation (Setting the IP Address) ............ 2-31 (E)

2-6-2. Setting the Switch ......................................... 2-31 (E)

3 (E)

NSS-V2

Purpose of this manual

This manual is the installation manual of Multi-format Media Server NSS-V2.

This manual is intended for use by trained system and service engineers, and

describes the information regarding installation.

Related manuals

Besides this Installation Manual, the following manuals are available for the

NSS-V2.

.NSS-V2 Operation Manual (supplied with the NSS-V2)

This manual describes the application and operation of the NSS-V2.

Part number: 3-903-845-XX

.NSS-V2 Maintenance Manual (available on request)

This manual describes the information that premise the service based on main

parts replacement (service overview, maintenance functions, replacement of the

parts and boards, circuit descriptions and block diagram, etc.).

If this manual is required, please contact your local Sony Sales Office/Service

Center.

Part number: 9-968-190-XX

Contents

The following is a summary of all the section for understanding the contents of this

manual.

Section 1 Installation

Explains the operating conditions, installation space, power supply, installation of

option board, rack mounting, connection, and checks after connection.

Section 2 Service Overview

Explains the procedure for cleaning the air filter, the function and factory setting of

the switches and LEDs on the board, procedures for operating Setup Tool, building

File Manager-PC, installing Transfer Manager, and setting McDATA FC Switch.

Trademarks

Trademarks and registered trademarks used in this manual are follows.

.Ethernet is a registered trademark of Xerox Corporation.

.Pentium is a registered trademark of Intel Corporation.

.Linux is a registered trademark of Linus Torvalds.

.Red Hat is a registered trademark of Red Hat, Inc.

.TimeSys and Time Sys Linux are registered trademarks of TimeSys Corp.

Manual Structure

1-1 (E)

NSS-V2

Section 1

Installation

1-1. Installation Procedure

The installation procedure of the NSS-V2 is shown in the following flowchart.

Refer to each item in this manual for details.

This unit is supplied with the following parts.

.Plug Holder 2 pcs

.Ornamental Washer 4 pcs

.Screw (RK5 x16) 4 pcs

.Operation Manual 1 pc

.Installation Manual 1 pc

.File Manager Software CD-ROM 1 pc

The following equipment is prepared

.The personal computer for installing the File Manager software

OS: Red Hat Linux ES, TimeSys Linux

CPU: Intel Xem 3.4 GHz or more

Memory: 2 GB or more

HDD: 36 GB or more

Ethernet: 100Base-TX

For the newest information on the personal computer, please contact your local Sony Sales Office/

Service Center.

Start

Determination

of Installation Space

Rack Mounting

Installation of

Option Boards

Connection

End

1-2. Operating Conditions

and Installation Space

1-3. Power Supply

1-4. Rack Mounting

1-5. Installation of Option Boards

1-6. Signal Input and Output

1-7. Connecting Connectors and Cables

1-8. Connection

1-2 (E) NSS-V2

1-2. Operating Conditions and Installation Space

Operating Conditions

Operating temperature +5 dC to +40 dC

Performance humidity 10 % to 90 % (No condensation)

Mass NSS-V2 : Approx. 21 kg

BKNS-V202 : Approx. 1 kg (per one set)

BKNS-V203 : Approx. 1 kg (per one set)

BKNS-V209 : Approx. 1 kg (per one set)

To prevent overheating of the NSS-V2 ensure that there is good air circulation around the unit.

Do not install the unit in humid or dusty environment.

Do not stack the units.

Andere Handbücher für NSS-V2

Inhaltsverzeichnis

Andere Sony Server Handbücher

Sony

Sony MAV-70 Bedienungsanleitung

Sony

Sony VGF-HS1 - Vaio Home Server Bedienungsanleitung

Sony

Sony Ipela SNT-EX101 Bedienungsanleitung

Sony

Sony MAV-2000 Bedienungsanleitung

Sony

Sony VSR-2000 Bedienungsanleitung

Sony

Sony NSR-500 Bedienungsanleitung

Sony

Sony WG-C20 Series Bedienungsanleitung

Sony

Sony WG-C10 Series Betriebsanleitung

Sony

Sony MAV-70 Bedienungsanleitung

Sony

Sony NSR 1050H - Standalone DVR - 16 CH Bedienungsanleitung

Sony

Sony NSR 1050H - Standalone DVR - 16 CH Bedienungsanleitung

Sony

Sony WG-C10 Series Bedienungsanleitung

Sony

Sony NSS-V2 Bedienungsanleitung

Sony

Sony VSR-2000A Bedienungsanleitung

Sony

Sony VGF-HS1 - Vaio Home Server Bedienungsanleitung

Sony

Sony HCD-CZ1 - Amplifier, Cd Player Merkblatt

Sony

Sony VGF-HS1 - Vaio Home Server Bedienungsanleitung

Sony

Sony FSV-VN7 Bedienungsanleitung

Sony

Sony IPELA NSR Series Bedienungsanleitung

Sony

Sony XDSPD1000 Bedienungsanleitung

Sony

Sony NSR Series Bedienungsanleitung

Sony

Sony RM-PP1 Bedienungsanleitung

Sony

Sony NSR-500 Bedienungsanleitung

Sony

Sony WG-C10 Series Referenzhandbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung