Sony CMT-RB5 - Micro Hi Fi Component System Bedienungsanleitung
Micro Hi-Fi
Component
System
4-230-861-11(1)
©2000 Sony Corporation
CMT-RB5
Operating Instructions
2
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
3
Table of Contents
Getting Started
Step 1: Hooking up the system ................ 4
Step 2: Setting the time ............................ 6
Step 3: Presetting radio stations ............... 7
Saving the power in standby mode* ......... 8
Basic Operations
Playing a CD ............................................. 9
Listening to the radio
— Preset Tuning............................... 10
The CD Player
Playing CD tracks repeatedly
— Repeat Play .................................. 11
Playing CD tracks in random order
— Shuffle Play ................................. 11
Programing CD tracks
— Program Play ............................... 12
Using the CD display .............................. 13
Other Features
Adjusting the sound ................................ 15
Using the Radio Data System
(RDS)**............................................ 16
Falling asleep to music
— Sleep Timer ................................. 16
Waking up to music — Daily Timer....... 17
Connecting optional
components
Connecting optional A/V components .... 19
Listening to the sound of
connected components ..................... 20
Recording to connected components ...... 21
Connecting external antennas ................. 21
Additional Information
Precautions .............................................. 23
Troubleshooting ...................................... 24
Specifications .......................................... 26
Parts descriptions for the remote............. 28
Index........................................................ 30
* North American and European models only
** European model only
4
Getting Started
Step 1: Hooking up the system
Perform the following procedure 1to 4to hook up your system using the supplied cords and
accessories.
11
2
4
1
3
1Connect the speakers.
Connect the speaker cords to the SPEAKER
terminals as shown below.
Main unit
L
+
–
+
–
R
Speaker
–
+
Note
Keep the speaker cords away from the
antennas to prevent noise.
AM loop antenna
FM antenna
Left speakerRight speaker
Red (3)
Black (#)
Insert this portion Red (3)
Black (#)
Insert this portion
5
Getting Started
2Connect the FM/AM antennas.
Set up the AM loop antenna, then connect it.
Jack type A
FM75Ω
COAXIAL
AM
U
Jack type B
FM
75Ω
AM
U
U
3For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.
VOLTAGE
SELECTOR
110-120V 220-240V
4Connect the power cord to a wall outlet.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).
Inserting two size AA (R6)
batteries into the remote
E
e
eE
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates the
system, replace both batteries with new ones.
Notes
• If you do not use the remote for a long period of
time, remove the batteries to avoid possible damage
from battery leakage.
• Be sure to insert the batteries in correct direction.
• Do not mix new batteries with old ones.
• Do not use different types of batteries together.
• Do not use a battery that is leaking.
• If the battery leaks, clean the battery compartment
and replace all the batteries with new ones.
AM loop
antenna
Extend the FM
lead antenna
horizontally
AM loop
antenna
Extend the FM
lead antenna
horizontally
6
Step 2: Setting the time
You must set the time beforehand to use the timer
functions.
The clock is on a 24-hour system for the European
model, and a 12-hour system for other models.
The 24-hour system is used for illustration
purposes.
>
Mm
NX x
?/1
.
21
4,6
4
3,5
DISPLAY
m
1Turn on the system.
2Press CLOCK/TIMER SET.
The clock appears and the hour indication
flashes.
0:00
3Press ./>to set the hour.
4Press ENTER or M.
The minute indication flashes.
11:00
5Press ./>to set the minute.
6Press ENTER.
The clock starts.
If you made a mistake
Press m/Mrepeatedly until the incorrect item
flashes, then set it again.
To change the preset time
You can change the preset time while the system
is off.
1Press DISPLAY to display the clock.
2Press CLOCK/TIMER SET.
3Repeat steps 3 to 6 of “Setting the time.”
Tips
• The upper dot of the colon flashes for the first 30
seconds, and the lower dot flashes for the last 30
seconds of each minute.
• Each time you press DISPLAY while the system is
off, the display switches between no display and the
clock display.
7
Getting Started
Step 3: Presetting radio
stations
You can preset up to 30 stations, 20 for FM and
10 for AM.
>
Mm
NX x
?/1
.
5
21
4
3
STEREO/
MONO
PRESET +/–
1Press TUNER/BAND to select “FM” or
“AM.”
Pressing TUNER/BAND turns on the
system.
2Press MODE repeatedly until “AUTO”
appears.
FM 78.50
3Press TUNING +/–.
The frequency indication changes and the
scanning stops when the system tunes in a
station. “TUNED” and “STEREO” (for a
stereo program) appear.
4Press MEMORY.
A preset number flashes in the display. The
stations are stored from preset number 1.
MEMORY MF1
5Press ENTER.
“COMPLETE !!” appears, and then the
station is stored.
6Repeat steps 1 to 5 to preset other
stations.
To stop scanning
Press MODE.
To tune in a station with a weak
signal
Press MODE repeatedly until “MANUAL”
appears in step 2, then press TUNING +/–
repeatedly to tune in the station manually.
To set another station to an
exist preset number
Start over from step 1. After step 4, press
PRESET +/– repeatedly to select the preset
number that you want to overwrite to. And then,
press ENTER.
continued
8
To erase a preset station
1Press down MEMORY until “ERASE” and a
preset number appear in the display.
2Press PRESET +/– repeatedly to select the
preset number that you want to erase.
Select “ALL ERASE” when you want to erase
all the preset stations.
3Press ENTER.
“COMPLETE !!” appears.
When you erase a preset number, the preset
number decreases by one and all preset numbers
following the erased one are renumbered.
To change the AM tuning
interval (except for the European
model)
The AM tuning interval is factory-set to 9 kHz
(10 kHz in some areas). To change the AM tuning
interval, tune in any AM station first, then turn off
the system. While pressing down the JL
button on the unit, turn the system back on. When
you change the interval, all the AM preset stations
are erased. To reset the interval, repeat the same
procedure.
Tips
• The preset stations are retained for about a day even
if you disconnect the power cord or if a power
failure occurs.
• When an FM stereo program has static noise, press
STEREO/MONO until “MONO” appears in the
display. There will be no stereo effect, but the
reception will improve. Press the button again to
restore the stereo effect.
Saving the power in
standby mode
(North American and European models only)
You can lower the power consumption to a
minimum and save energy in the standby mode.
The system is set at the factory not to display the
clock when the system is off (Power Saving
Mode). To display the clock even when the
system is off, deactivate the Power Saving Mode.
7
s
J L
Z
l j
c
DISPLAY
,Press DISPLAY when the system is off.
The system switches off the Power Saving
Mode and the clock appears.
To activate Power Saving Mode
Press DISPLAY.
The clock disappears.
Tip
Each time you press DISPLAY in the standby mode,
the display switches between the Power Saving Mode
and the clock display.
Step 3: Presetting radio stations
(continued)
9
Basic Operations
Basic Operations
Playing a CD
To turn on the system, press ?/1(power).
7
s
J L
Z
l j
c
21
l j J L VOLUMEs
1Press Zand place a CD on the disc
tray.
7
s
J L
Z
l j
c
To close the disc tray, press Zagain.
2Press HS.
The disc tray closes and play starts.
The CD TEXT indicator lights up when the
system detects a CD TEXT disc.
CD1 30m s5
Track number Playing time
To Do this
Stop play Press s.
Pause Press HS. Press again to resume
play.
Select a track Press lj/JL
repeatedly.
Press down lj/JL
during play and release it at the
desired point. “–OVER–” appears
at the end of the CD.
Turn VOLUME.
Remove the CD Press Z.
Adjust the
volume
Tips
• If there is no CD in the player, “CD No Disc”
appears in the display.
• Pressing HS when the system is off automatically
turns on the system and starts CD play if there is a
CD on the disc tray (One Touch Play).
• You can switch from another source to the CD
player and start playing a CD just by pressing HS
(Automatic Source Selection).
• You can start playing from the desired track in
step 2.
1Press lj/JLrepeatedly until the
desired track appears.
2Press HS.
Notes
• Do not use a CD with tape, seals or paste on it as
this may damage the CD player.
• Do not push the disc tray to close it, as this may
damage the CD player. Press Zto close the disc
tray.
• The disc cannot be viewed through the front
window when a CD single (8 cm CD) is loaded.
• The characters printed on the CD appear upside
down when viewed through the front window.
With the
label side up.
When you
play a CD
single (8 cm
CD), place it
on the inner
circle of the
tray.
Find a point in
a track
CD TEXT
indicator
?/1(power)
Getting Started/Basic Operations
9
10
Listening to the radio
— Preset Tuning
Preset radio stations in the tuner’s memory first
(see page 7).
To turn on the system, press ?/1(power).
>
Mm
NX x
?/1
.
21
STEREO/
MONO
VOL –
TUNING – TUNING +
VOL +
33
1Press TUNER/BAND to select “FM” or
“AM.”
2Press MODE repeatedly until
“PRESET” appears.
FM 78.50
3Press PRESET +/– to select the desired
preset station.
FM 1 785.0
When you preset only one station,
“ONE PRESET” appears in the display.
* European model only
?/1
(power)
To Do this
Turn off the radio Press ?/1to turn off the
system.
Adjust the volume Press VOL +/– repeatedly
Listening to non-preset radio
stations
• Press MODE repeatedly until “MANUAL”
appears in step 2, then press TUNING +/–
repeatedly to tune in the desired station
(Manual Tuning).
• Press MODE repeatedly until “AUTO” appears
in step 2, then press TUNING +/–. The
frequency indication changes and the scanning
stops when the system tunes in a station
(Automatic Tuning).
To cancel Automatic Tuning
Press MODE.
Tips
• Pressing TUNER/BAND when the system is off
automatically turns on the system and tunes in the
last received station (One Touch Play).
• You can switch from another source to the tuner
just by pressing TUNER/BAND (Automatic
Source Selection).
• To improve broadcast reception, adjust the supplied
antennas, or connect a commercially available
external antenna (see page 21).
• When an FM stereo program has static noise, press
STEREO/MONO until “MONO” appears in the
display. There will be no stereo effect, but the
reception will improve. Press the button again to
restore the stereo effect.
Frequency (or RDS
station name*)
Preset number
Inhaltsverzeichnis
Andere Sony Stereoanlage Handbücher
Sony
Sony ICF-DS15iPN Bedienungsanleitung
Sony
Sony HCD-XB66 Bedienungsanleitung
Sony
Sony HTC-V5550 Bedienungsanleitung
Sony
Sony MEX-BT38UW - Bt Slot Usb 1wire Bedienungsanleitung
Sony
Sony MEX-N4280BT Bedienungsanleitung
Sony
Sony HCD-GN1100D Bedienungsanleitung
Sony
Sony CFD-E10 Marketing Bedienungsanleitung
Sony
Sony HCD-D90AV Bedienungsanleitung
Sony
Sony CMT-S20 Bedienungsanleitung
Sony
Sony MEX-M100BT Bedienungsanleitung
Sony
Sony ICF-C11iP Bedienungsanleitung
Sony
Sony CMT-BT60 Bedienungsanleitung
Sony
Sony ZS-RS60BT Bedienungsanleitung
Sony
Sony CMT-HX3 Bedienungsanleitung
Sony
Sony HCD-RG550 Bedienungsanleitung
Sony
Sony HCD-RG121 Bedienungsanleitung
Sony
Sony CFD-S50 Bedienungsanleitung
Sony
Sony MHC-V77W Referenzhandbuch
Sony
Sony MHC-ECL7D Bedienungsanleitung
Sony
Sony MHC-D60 Bedienungsanleitung
