Sony CMT-VP1 Bedienungsanleitung
Operating Instructions
Micro HiFi
Component
System
3-867-409-12(1)
©1999 by Sony Corporation
CMT-VP1
2
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
This system is equipped with the Dolby* B-type noise
reduction system.
* Dolby noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol ;are
trademarks of Dolby Laboratories Licensing
Corporation.
This system can play the
following discs
VIDEO CDs Audio CDs
Disc logo
Contents Audio + Video
(moving pictures) Audio
Disc size 12 cm/8 cm 12 cm/8 cm
Play time 74 min./20 min. 74 min./20 min.
Note on VIDEO CDs
This system conforms to VIDEO CDs without PBC
functions (Ver. 1.1) and VIDEO CDs with PBC
functions (Ver. 2.0) of VIDEO CD standards. You
can enjoy two kinds of playback according to the disc
type.
Disc type You can
VIDEO CDs without
PBC functions
(Ver. 1.1 discs)
Enjoy video playback
(moving pictures) as well as
audio CDs.
VIDEO CDs with
PBC functions
(Ver. 2.0 discs)
Play interactive software
using menu screens displayed
on the TV screen (menu
playback), in addition to the
video playback function of
VIDEO CDs without PBC
functions.
Moreover, you can play high
or standard quality still
picture.
* PBC = Play Back Control
3
Table of Contents
Getting Started
Step 1: Hooking up the system ................ 4
Step 2: Setting the time ............................ 7
Step 3:
Presetting radio stations — Preset ..
8
Connecting optional components .............. 9
Basic Operations
Playing a VIDEO CD.............................. 12
Playing a CD — Normal Play ................. 13
Recording from a CD/VIDEO CD to a tape
— CD Synchro Recording ............... 14
Listening to the radio — Preset Tuning .. 16
Recording from the radio ........................ 17
Playing a tape .......................................... 19
Singing along: Karaoke.......................... 20
The VIDEO CD/CD Player
Playing a VIDEO CD with PBC functions
(Ver. 2.0) –– PBC Play..................... 22
Checking the remaining playing time ..... 23
Using the on-screen display .................... 24
Resuming VIDEO CD playback from the
point last stopped at
–– Resume Play ................................ 27
Playing CD tracks repeatedly
— Repeat Play .................................. 28
Playing CD tracks in random order
— Shuffle Play ................................. 28
Playing CD tracks in a favorite order
–– Program Play ............................... 29
The Tape Deck
Recording to a tape manually.................. 30
Recording your favorite CD tracks to a tape
— Program Edit................................ 31
Other Features
Generating a more dynamic sound.......... 33
Falling asleep to music — Sleep Timer .. 33
Waking up to music — Daily Timer....... 34
Timer-activated recording of radio
programs — REC Timer .................. 35
Additional Information
Precautions .............................................. 37
Troubleshooting ...................................... 38
Specifications .......................................... 40
Glossary .................................................. 42
Parts identification for the remote........... 42
Index.......................................... Back cover
4
2Connect the FM and AM antennas.
Set the AM loop antenna up before
connecting it.
AM
ANTENNA
U
FM75Ω
U
1Connect the speakers.
Connect the right and left speaker cords to
the SPEAKER terminals as shown below.
3
L
#
#
R
3
Note
Keep the speaker cords away from the antennas
to prevent noise.
1
6
5
4
2
3
Getting Started
Step 1: Hooking up the system
Follow steps 1through 6of the procedure below to hook up your system using the supplied cords and
accessories.
AM loop antenna
FM antenna
Right speaker Left speaker
Red (3)
Black (#)
Insert this
portion
AM loop
antenna
Extend the FM
wire antenna
horizontally
5
Getting Started
3Connect the VIDEO OUT jack to the
video input jack on your TV with the
supplied video connecting cord.
VIDEO OUT
When using a TV
Turn on your TV and set the input selector to
video input so you can view the pictures from
the system.
4Set SYSTEM SELECT (color system)
to PAL or NTSC depending on the
color system of your TV.
AUTO
SYSTEM
SELECT
NTSC PAL
If your TV automatically
changes the color system
according to the input signal:
Set SYSTEM SELECT to AUTO (the
factory setting). The video signal will be
output in the color system of the VIDEO CD
being played back.
If the color system of your TV
is NTSC:
Set SYSTEM SELECT to NTSC.
When this system is selected, video images
recorded in the PAL system will be stretched
vertically, and the upper and lower parts of the
picture will be cut off.
If the color system of your TV
is PAL:
Set SYSTEM SELECT to PAL.
When this system is selected, video images
recorded in the NTSC system will be stretched
horizontally, and the upper and lower parts of
the screen will be masked in black.
Note
Be sure to turn off the system before you change
the SYSTEM SELECT setting.
5For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.
VOLTAGE
SELECTOR
110V~120V
220V~240V
6Connect the power cord to a wall outlet.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).
continued
6
Inserting two size-AA (R6)
batteries into the remote
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates the
system, replace both batteries with new ones.
Notes on batteries
• Make sure the battery poles (plus/minus) are
properly oriented.
• Do not use a new battery with an old one.
• Do not use different types of batteries together.
• If you do not use the remote for a long period of
time, remove the batteries to prevent possible
damage from battery leakage and corrosion.
• Do not use a battery that is leaking.
• If a battery has leaked, clean the battery
compartment and replace all the batteries.
• Do not place the remote in an extremely hot or
humid place.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
Using the remote
You can use the shaded buttons shown below to
operate a Sony TV set.
++
––
?/1
TV
VOL
+ / –
TV ?/1 TV/VIDEO
TV CH
+ / –
To Press
Step 1: Hooking up the system
(continued)
Turn the TV on or off TV ?/1.
Switch the TV’s video
input TV/VIDEO.
Change the TV
channel TV CH +/–.
Adjust the volume of
the TV speaker(s) TV VOL +/–.
7
Getting Started
Step 2: Setting the time
Before you can use the system’s timer functions,
set the internal clock.
+
–
#
2
H
Ss
hH lL z
jJ 6
12,4
3,5
1Press TIMER SET.
The hour indication flashes.
AM1200
2Press +/– repeatedly to set the hour.
AM1100
3Press ENTER.
The minute indication flashes.
AM1100
4Press +/– repeatedly to set the minute.
AM1110
5Press ENTER.
The clock will begin operating.
To reset the system clock
You can reset the system clock even when the
system is on or off. To reset the time while the
system is on, do the following:
1Press TIMER SET.
2Press +/– repeatedly until “SET CLOCK”
appears, then press ENTER.
3Repeat step 2 to 5 in “Step 2: Setting the time”.
Tip
If you make a mistake, start over from step 1.
8
2Press TUNER BAND to select FM or
AM.
3Press TUNING MODE repeatedly until
“AUTO” appears.
4Press TUNING +/–.
The frequency changes as the system scans
for a station. Scanning stops automatically
when a station is tuned in. At that time,
“TUNED” and “STEREO” (for stereo
programs only) appear.
FM1005
AUTO
STEREO
TUNED
M
H
z
5Press MEMORY on the remote.
A preset number flashes.
1FM1005
STEREO
TUNED
M
H
z
PRESET
6Press l/Lon the remote
repeatedly to select the preset number
that you want.
3FM1005
STEREO
TUNED
M
H
z
PRESET
7Press ENTER on the remote.
The station is stored to the selected preset
number.
8Repeat steps 2 through 7 to preset other
stations.
Step 3: Presetting radio
stations
— Preset
The system can store a total of 30 preset stations
(20 for FM and 10 for AM). This section explains
how to tune in stations and preset them.
Z
bB x
mM
Xz
Z
ux
.>
mM
+
–
?/1
4
12
3
+
–
#
2
O
H
Ss
hH lL z
jJ 6
7
6
5
1Press TUNER.
“TUNER” appears.
9
Getting Started
To tune in a weak station
In step 3, press TUNING MODE repeatedly until
“AUTO” and “PRESET” disappear, then press
TUNING +/– repeatedly to tune in the station.
To change the preset number
Start over from step 2.
Tip
The preset stations are saved in the system’s memory
for about two days even if you disconnect the power
cord or a power failure occurs.
To change the AM tuning
interval (not applicable on the
Middle Eastern model)
The AM tuning interval is factory-preset to 9 kHz. To
switch the AM tuning interval, tune in any AM
station first, then turn off the system. Pressing
TUNING + down, turn the system back on. When
you change the interval, all the AM preset stations are
erased. To change back to the original interval, repeat
the same procedure.
Connecting optional
components
This section explains how to connect a variety of
components to your system in order to enhance it.
Refer to the instructions included with each
component for details.
Connecting audio components
Connecting an MD deck for
analog recording
You can connect an MD deck to the system with
commercially available audio cords. Be sure to
match the color-coded pins to the appropriate
jacks. To listen to the MD deck after connecting it,
press MD/VIDEO until “MD” appears.
To the audio input jacks on the
MD deck
To the audio output jacks on the MD
deck
continued
10
Connecting an MD deck for
digital recording
By connecting an MD deck to the system with a
commercially available optical cable, you can
make a digital recording from a CD.
To the digital input connector
on the MD deck
Note
You cannot make a digital recording from a
VIDEO CD to an MD deck through an optical
cable. You can, however, make an analog
recording through an optional audio connected to
the LINE OUT jacks. (See “Connecting an MD
deck for analog recording.”)
Connecting optional components
(continued)
Connecting a VCR
You can connect a VCR to the system with a
commercially available audio cord. Be sure to
match the color-coded pins to the appropriate
jacks. To listen to the VCR after connecting it,
press MD/VIDEO until “VIDEO” appears.
By connecting the audio output jacks on your
VCR to the VIDEO IN jacks using an optional
audio cord, you can enjoy powerful stereo sound
with the video playback.
Moreover, if you connect the audio input jacks on
your VCR to the LINE OUT jacks and VIDEO
OUT jack using the supplied video connecting
cord, you can record the audio and video signals
from a VIDEO CD onto video tape.
To the audio output
jacks on the VCR
To the video input
jack on the VCR
To the audio input
jacks on the VCR
Inhaltsverzeichnis
Andere Sony Stereoanlage Handbücher
Sony
Sony HCD-GRX8 Bedienungsanleitung
Sony
Sony LBT-D570 - Compact Hifi Stereo System Bedienungsanleitung
Sony
Sony HCD-RG333 Bedienungsanleitung
Sony
Sony HCD-DV2D - Dvd / Reciever Component Bedienungsanleitung
Sony
Sony HCD-VX880AV Bedienungsanleitung
Sony
Sony HCD-GN660 Bedienungsanleitung
Sony
Sony 3-300-703-11(2) Bedienungsanleitung
Sony
Sony MHC-D60 Bedienungsanleitung
Sony
Sony CMTDX2D - Micro System Bedienungsanleitung
Sony
Sony HCD-PX333 Bedienungsanleitung
Sony
Sony MHC-RXD9 - 3 Cd Mini System Bedienungsanleitung
Sony
Sony CMT-HPX10W - Micro Hi Fi Component System Bedienungsanleitung
Sony
Sony GMT-GP7 Bedienungsanleitung
Sony
Sony SRS-XB2 Bedienungsanleitung
Sony
Sony MHC-RV990D Bedienungsanleitung
Sony
Sony NAS-Z200IR Bedienungsanleitung
Sony
Sony CX-JV77 Bedienungsanleitung
Sony
Sony ZS-Y3 - Personal Cd Audio System Bedienungsanleitung
Sony
Sony HCD-AZ33D Bedienungsanleitung
Sony
Sony MHC-V43D Referenzhandbuch
