Sony DSR-DU1 Bedienungsanleitung

DSR-DU1

3-620-597-11 (1)

Video Disk Unit

Operating Instructions

Before operating the unit, please read this manual

thoroughly and retain it for future reference.

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do notopen the

cabinet. Refer servicing to qualified

personnel only.

For customers in the USA

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your

authority to operate this equipment.

The shielded interface cable recommended in this

manual must be used with this equipment in order to

comply with the limits for a digital device pursuant to

Subpart B of Part 15 of FCC Rules.

For customers in Europe

This product with the CE marking complies with the

EMC Directive (89/336/EEC) issued by the

Commission of the European Community.

Compliance with these directive implies conformity to

the following European standards:

EN55103-1: Electromagnetic Interference (Emission)

EN55103-2: Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following

Electromagnetic Environment(s):

E1 (residential), E2 (commercial and light industrial),

E3 (urban outdoors) and E4 (controlled EMC

environment, ex. TV studio).

Voor de Klanten in Nederland

Gooi de batterij niet weg maar lever deze in als klein

chemisch afval (KCA).

WARNING

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig

håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

ADVARSEL

Lithiumbatteri - Eksplosjonsfare.

Ved utskifting benyttes kun batteri som

anbefalt av apparatfabrikanten.

Brukt batteri returneres

apparatleverandøren.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en likvärdig typ

som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt gällande

föreskrifter.

VAROITUS

Paristo voi räjähtää jos se on virheellisesti

asennettu.

Vaihda paristo ainoastaan laitevalmistajan

suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

Table of Contents

Overview .................................................................4

Features of This Unit ..........................................4

Supported Camcorders .......................................4

Using the CD-ROM Manual ..............................5

Getting the Best Performance from the DSR-DU1

..................................................................................6

Places to Avoid ...................................................6

Operation ............................................................6

Care of the Unit ..................................................6

Names and Functions of Parts ..............................7

DSR-DU1 Video Disk Unit (in Supplied Case)

...........................................................................7

DSR-DU1 Video Disk Unit (Removed From

Supplied Case) ...............................................10

CA-DU1 Camera Adaptor (option) ..................11

Example System Configurations ........................12

Connectingto a Camcorder With ani.LINK Cable

.........................................................................12

Connecting to a Camcorder Through the CA-DU1

Camera Adaptor .............................................13

Use As a Source Feeder Supporting the SBP2

Protocol ..........................................................14

Use As a Source Feeder for a Nonlinear Editing

System ............................................................14

Inserting and Replacing the Lithium Battery ...15

Operation .............................................................16

Preparing the Power Supply .............................16

Menu Settings ...................................................17

Coupled Recording on the Camcorder Tape and

Hard Disk .......................................................17

Recording the Image From theCamcorder to Hard

Disk ................................................................18

Reviewing Content Immediately After Recording

– a Recording Review Operation ...................19

Keeping a Recording of the Last Few Seconds of

Material Before Pressing the Recording Button

– Cache Recording ........................................20

Time-Lapse Recording (or Interval Recording) 20

Playback ...........................................................20

Setting Cue Points ............................................21

Deleting Recorded Material (Clips) .................21

Menus ...................................................................22

Menu Organization and Content ......................22

Making Menu Settings .....................................23

LCD and Indicator Error Indications ...............25

Specifications ........................................................26

DSR-DU1 Video Disk Unit ..............................26

CA-DU1 Camera Adaptor (option) ..................26

Getting the Best Performance From the Batter

................................................................................27

Overview

Features of This Unit

The DSR-DU1 Video Disk Unit incorporatesa 2.5-inch,

40 gigabyte hard disk.

Connected to a Sony digital camcorder through the

i.LINK interface, it is capable of recording at least three

hours of video and audio signals in DVCAM format or

DV format.

Integral camcorder mounting with

dedicated adaptor

The optional CA-DU1 Camera Adaptor enables this unit

to be attached to a digital camcorder (DSR-370/370P/

570WS/570WSP or DSR-250/250P/300A/300AP/

500WS/500WSP) equipped with an i.LINK interface.

Using the CA-DU1 makes attachment to the camcorder

safe and simple.

Increased recording times for compact

camcorders

If your camcorder is a DSR-PD100A/PD100AP/PD150/

PD150P (equipped with i.LINK interface), connect this

unit directly to the comcorder using an i.LINK cable in

place of the adaptor. This provides arecording time of at

least three hours, equivalent to the recording time of a

standard size DVCAM tape.

Recording can continue on the DSR-DU1 while

changing the tape.

Use as an independent source feeder

Connected to a nonlinear editing system, the DSR-DU1

can be used as an independent source feeder. Further,

using the same principle as in dubbing with a

conventional VCR, video and audio signals can be

provided to another device equipped with the i.LINK

interface. The AV/C protocol can be used in this case.

Transfer of single files to an editor

Data recorded on the DSR-DU1 can be transferred as a

file to a computer hard disk or similar, allowing efficient

inclusion of material into a nonlinear editing system.

The SBP2 protocol can be used for file transfer.

Convenient recording functions

• When DUPLICATE mode is set, you can record the

same content on the DSR-DU1 and the connected

camcorder.

• To avoid losing important scenes, the cache recording

function keeps up to eight seconds of video in

memory.

• For monitoring purposes, the interval recording

function provides long-term recording.

Supported Camcorders

The DSR-DU1 can be used connected to any of the

following camcorders.

• DSR-370/370P

• DSR-570WS/570WSP

• DSR-300A/300AP

• DSR-500WS/500WSP

• DSR-250/250P

• DSR-PD100A/PD100AP

• DSR-PD150/PD150P

• DCR-VX2000/VX2000E

Differences in supported units

The functions offered by the DSR-DU1 are restricted in

some cases, depending on the connected camcorder.

Details of differences in restrictions and characteristics

are also described where necessary in the section

“Operation” (page 16).

a) It is necessary to change the factory default settings on the camcorder.

DSR-370/

370P/

570WS/

570WSP

DSR-300A/

300AP/

500WS/

500WSP

DSR-250/

250P

Recording with

camcorder start/

stop button

Yes even

without tape

Coupled to

tape Coupled to

tape

Playback on

camcorder b) Yes in

viewfinder No Yes, in

viewfinder

and LCD

Monitor output

from camcorder Yes No Yes

Recording the

camcorder video

with the DSR-

DU1 switch

Yes even

without tape Yes even

without tape

DSR-

PD150/

PD150P

DSR-

PD100A/

PD100AP

DCR-

VX2000/

VX2000E

Recording with

camcorder

start/stop button

Coupled to

tape Coupled to

tape c) Coupled to

tape c)

Playback on

camcorder a) Yes, in

viewfinder or

LCD

Yes, in

viewfinderor

LCD

Yes, in

viewfinder or

LCD

Monitor output

from camcorder Yes Yes Yes

Recording the

camcorder

video with the

DSR-DU1

switch

Yes even

without tape Yes even

without tape a)

Overview 5

b) After a few minutes elapse without recording on the tape, the

camcorder powers off. With the DSR-370/370P/570WS/570WSP, it is

necessary to set the VTR TRIGGER switch to the “EXT ONLY”

position.

c) For camcorders other than the DSR-370/370P/570/570WSP, it is

necessary to switch from camera mode to VTR mode.

Using the CD-ROM Manual

The supplied CD-ROM includes operation manuals for

the DSR-DU1 series of camera control unit (English,

French, German, Italian Spanish and Chinese versions).

CD-ROM System Requirements

The following are required to access the supplied CD-

ROM disc.

• Computer: PCwith MMX Pentium 166 MHz or faster

CPU, or Macintosh computer with PowerPC CPU.

– Installed memory: 32 MB or more

–CD-ROMdrive:× 8 or faster

• Monitor: Monitor supporting resolution of 800 ×600

or higher

When these requirements are not met, access to the CD-

ROM disc may be slow, or not possible at all.

Preparations

The following software must be installed on your

computer in order to use the operation manuals

contained in the CD-ROM disc.

• Microsoft Internet Explorer Version 4.0 or higher, or

Netscape Navigator Version 4.0 or higher

• Adobe Acrobat Reader Version 4.0 or higher

Notes

• If Microsoft Internet Explorer is not installed, it may

be downloaded from the following URL:

http://www.microsoft.com/ie

• If Netscape Navigator is not installed, it may be

downloaded from the following URL:

http://home.netscape.com/

• If Adobe Acrobat Reader is not installed, it may be

downloaded from the following URL:

http://www.adobe.com/products/acrobat/

readstep.html

To Read the CD-ROM Manual

To read the operation manual contained in the CD-ROM

disc, do the following.

Insert the CD-ROM disc in your CD-ROM drive.

A cover page appears automatically in your

browser.

If it does not appear automatically in the browser,

double click the index.htm file on the CD-ROM

disc.

Select andclick the operation manual that you want

to read.

A PDF file of the operation manual opens.

Note

If you lose the CD-ROM disc or become unable to

read its content, for example because of a hardware

failure, contact a Sony service representative.

• MMX and Pentium are registered trademarks of Intel Corporation or its

subsidiaries in the United States and other countries.

• PowerPC is a registered trademark of International Business Machines

Corporation.

• Macintosh is a registered trademark of Apple Computer, Inc.

• Microsoft is a registered trademark of Microsoft Corporation in the

United States and/or other countries.

• Netscape Navigator is a registered trademark of Netscape

Communications Corporation in the U.S. and other countries.

• Adobe and Acrobat are registered trademarks of Adobe Systems

Incorporated in the United States and/or other countries.

Getting the Best Performance from the DSR-DU1

Getting the Best

Performance from the

DSR-DU1

Places to Avoid

Do not leave the unit in the following places, whether

operating or stored. Doing so could lead to a

malfunction.

• Placessubjecttoveryhightemperatures.The insideof

a car with the windows closed in hot sun can reach an

extremely high temperature, and if the unit is left there

it may be deformed or malfunction.

• Places exposed to direct sunlight or close to heating

equipment. The unit may be deformed or malfunction.

• Places subject to extreme vibration

• Places subject to strong magnetic fields

• Sanddunes,sandybeaches,andotherplacessubjectto

blown sand. At the seashore and in other sandy

locations where there may be blown sand, ensure that

the sand does not reach the unit. This could cause not

only a malfunction, but in some cases render the unit

unrepairable.

Operation

• Do not operate where the unit would be exposed to a

powerful electromagnetic radiation. Recording and

playback may not function correctly.

• Do not operate close to a television or radio receiver.

There may be interference from thetelevision or radio

receiver.

• Do not connect the AC adaptor/charger or charger to

an electronic voltage-changer. This may cause heat to

be generated, or lead to malfunction.

Care of the Unit

If the unit is dirty, clean it by wiping with a soft cloth.

• If very dirty, use a cloth steeped in diluted mild

detergent and wrung out well to wipe the unit clean,

then finish off with a dry cloth.

• Do notuse alcohol, thinners, orother organic solvents.

These can cause the material of the unit to deteriorate,

or remove the finish.

• If using a chemically impregnated cloth, follow the

instructions supplied with the cloth.

• Avoid getting volatile liquids such as insecticides on

the unit, or leaving it in contact with rubber or plastic

products for a long time, as this can cause the material

of the unit to deteriorate, or remove the finish.

Names and Functions of Parts 7

Names and Functions of Parts

DSR-DU1 Video Disk Unit (in Supplied Case)

aDC IN connector

Connect the powersupplyto the DSR-DU1 from an

AC adaptor or similar.

bDV IN/OUT connector (4-pin, IEEE1394

compliant)

Connect to a camcorder or computer with an

i.LINK cable.

cREMOTE connector

Connect the remote controller supplied with the

unit.

dCUE button

Press this to enter a cue point. You can enter cue

points either during recording or playback, and a

maximum of 400 cue points can be set.

eSTART/STOP button

This starts or stops recording on this unit.

fTally/access indicator

The color this lights indicates the state.

Red: During recording

Green: During hard disk access

Orange: During cue point entry

This also flashes to indicate a problem with the

DSR-DU1 (see page 25).

gLIGHT ON/OFF button

3REMOTE connector

4CUE button

5START/STOP button

6Tally/access indicator

7LIGHT ON/OFF button

9MENU button

q; POWER switch

qa WARNING

indicator

qs STOP button

qd .button

qf Bbutton

2DV IN/OUT connector

1DC IN connector

qh LCD monitor

qj Jog dial

qk Remote controller

ql i.LINK cable

qg >button

8Ventilation outlet

Names and Functions of Parts

This turns the LCD monitor light on or off.

hVentilation outlet

This is the outlet from the cooling fan.

Note

Be careful not to obstruct the ventilation opening.

iMENU button

Pressing this button displays the menu in the LCD

monitor (see page 22). Press once more to return to

the DSR-DU1 status display (see next item).

jPOWER switch

This powers the DSR-DU1 on or off.

kWARNING indicator

This indicator lights or flashes when there is a

problem with the DSR-DU1 (see page 25).

lSTOP button

During playback from the DSR-DU1 hard disk,

pressing this button stops the playback.

m.(previous) button

During playback, pressing this makes a reverse

search at ×5 speed.

When stopped, pressing this button once moves to

the previous recording start point. Holding down

the button for at least two seconds moves back 10

clips*.

*In this system, the term “clip” is used to refer to

the unit of recording from the start point to the end

point.

nB(playback) button

Thisplays back fromanypositionontheDSR-DU1

hard disk.

o>(next) button

During playback, pressing this makes a forward

search at ×5 speed.

When stopped, pressing this button once moves to

the next recording start point. Holding down the

button for at least two seconds moves forward 10

clips*.

*In this system, the term “clip” is used to refer to

the unit of recording from the start point to the end

point.

pLCD monitor

This shows the DSR-DU1 status (see next item) or

a menu (see page 22).

qJog dial

This is used to operate the menu displayed on the

LCD monitor, and change TC/UB/clip settings.

Turn the dial to select an item, and press to confirm

(see page 23).

rRemote controller

Connect to the REMOTE connector on the main

unit. This has a START/STOP button, CUE button,

and tally indicator, and the button functions are the

same as those on the main unit. The tally indicator

lights red only during recording.

si.LINK cable

This cable is supplied with the DSR-DU1, and has

a 4-pin connector at each end. Connect the L-

shaped end to the main unit.

LCD monitor display

When the LCD monitor is not displaying the menu, it

shows the DSR-DU1 status as follows.

Display

area Type Indication Meaning

ACommand PLAY Playback

P-PAUSE Playback paused

REC Recording

R-PAUSE Recording paused

FWD Search forward

REV Reverse search

STOP Stopped

>> Moving to next

recording start

point

<< Movingtoprevious

recording start

point

PC-REMOTE Using SBP2

protocol

BRecording

mode Blank Normal

INT Interval recording

YALP RCT

KSI :HH:MM:SSFF

XXim

DTTAB

Names and Functions of Parts 9

PARA Coupled to

camcorder

Blank When Ais “PC-

REMOTE”

DUPLICATE DUPULICATE

mode

CTimecode

type TCR Timecode reader

timecode

TCG Timecode

generator timecode

UBR Timecode reader

user bit data

UBG Timecode

generator user bit

data

Clip No. xxxx 4 characters

Blank When Ais “PC-

REMOTE”

DTimecode

mode Blank Drop-frame mode

NDF Non-drop-frame

mode

ETimecode

generator

mode

Blank

EXT Locked to external

timecode

FCache

recording Blank Cache recording

function is off.

CACHE Cache recording

function is on.

GTimecode

value

(When C

is TCR or

TCG)

hh:mm:ss:ff While the jog dial

is pressed, this

shows the

recording time as

hh:mm:ss.

User bit

value

(When C

is UBR or

UBG)

xx yy zz ww While the jog dial

is pressed, this

shows the

recording date

Time from

beginning

of file

(When C

is a file

name)

hh:mm:ss While the jog dial

is pressed, this

shows the

recording length of

the file.

--:--:--:-- When Ais “PC-

REMOTE”

HRemaining

hard disk

capacity

DISK XXXmin

Display

area Type Indication Meaning

IRemaining

main

battery

capacity

BATT

[xxxx]Adequate battery

capacity

BATT

[xxx ]

BATT

[xx ]

BATT

[x ]

(1 flash/second)

BATT

(4 flashes/second) Inadequate

capacity to operate

JRemaining

backup

battery

capacity

(1 flash/second)

(4 flashes/second)

Battery should be

replaced.

Since data integrity

cannot be

guaranteed,it is not

possible to write to

the hard disk.

KAlarms MEMORY Shock-proof

memory is full.

i.LINK

(1 flash/second) Wheni.LINKinput

cannot be detected,

this flashes once

per second. This

does not apply for

i.LINK output.

Display

area Type Indication Meaning

Names and Functions of Parts

DSR-DU1 Video Disk Unit (Removed From Supplied Case)

aUNLOCK lever

To remove the main unit from the supplied case,

first press this lever down.

bRelease button

To remove the main unit from the supplied case,

press the UNLOCK lever down, then hold in this

button while removing the unit.

cBackup battery box

Open the lid, and insert the supplied lithium battery

(CR2032). This acts as a backup power supply for

the main unit.

For details of fitting and replacement, see

“Inserting and Replacing the Lithium Battery”

(page 15).

Note

This unit keeps data required to protect the hard

disk data using the backup power supply.

Therefore, when the backup battery capacity is low,

recording is not possible.

dMain battery box

Fit the optional NP-F960/F750 battery pack. This

acts as the main power supply for the DSR-DU1.

To remove the battery pack, hold down the PUSH

button on the side of the box.

For details of fitting, see “Fitting the battery “

(page 17).

1UNLOCK lever

2Release button DSR-DU1 main unit

3Backup battery box

Supplied case

To remove the unit from the

case, press down 1, then hold

in 2while withdrawing the unit

in the direction of the arrow.

4Main battery box

Andere Handbücher für DSR-DU1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Lagerung Handbücher

Sony

Sony SDX-900V Series Montageanleitung

Sony

Sony VPCL135FX Leitfaden

Sony

Sony SDX-500V Bedienungsanleitung

Sony

Sony AIT-SDX560 Montageanleitung

Sony

Sony Memory Stick PRO MSX-4GN Bedienungsanleitung

Sony

Sony CSM-100BS Bedienungsanleitung

Sony

Sony PHU-220R Bedienungsanleitung

Sony

Sony BKMA-U55 Bedienungsanleitung

Sony

Sony MicroVault USM-M1 Series Bedienungsanleitung

Sony

Sony WALKMAN CKL-NWE020 Bedienungsanleitung

Sony

Sony MSH-M128A Operating Instructions (primary... Bedienungsanleitung

Sony

Sony HD-E Series Bedienungsanleitung

Sony

Sony SDX-D550V Handbuch

Sony

Sony MSX-M256S Bedienungsanleitung

Sony

Sony HDPS-M10 - Data Storage Wallet Bedienungsanleitung

Sony

Sony StorStation AITi90 Bedienungsanleitung

Sony

Sony Microdrive RHMD2G Bedienungsanleitung

Sony

Sony SDX-300 Series Bedienungsanleitung

Sony

Sony XQD QD Series Bedienungsanleitung

Sony

Sony MSAC-US40 - MemoryStick Flash Memory Card USB 2.0... Bedienungsanleitung

Sony

Sony VGC-RB10M - Vaio Desktop Computer Bedienungsanleitung

Sony

Sony SDT-9000 Series Bedienungsanleitung

Sony

Sony SF Series Bedienungsanleitung

Sony

Sony MS-M16/TQ Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung