Sony XDCAM XDJ-1000 Bedienungsanleitung

PROFESSIONAL DISC LIBRARY

XDJ-1000

PROFESSIONAL DISC DRIVE

XDBK-J102

INSTALLATION MANUAL

1st Edition (Revised 1)

Serial No. 10001 and Higher: XDJ-1000 (SY)

XDJ-1000

!警告

このマニュアルは，サービス専用です。

お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，

人身事故につながることがあります。

危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。

!WARNING

This manual is intended for qualiﬁed service personnel only.

To reduce the risk of electric shock, ﬁre or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualiﬁed to do so. Refer all servicing to

qualiﬁed service personnel.

!WARNUNG

Die Anleitung ist nur für qualiﬁziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualiﬁziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Aﬁn

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualiﬁé pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

安全のために，周辺機器を接続する際は，過大電圧を持

つ可能性があるコネクターを以下のポートに接続しない

でください。

: （LAN）コネクター

上記のポートについては本書の指示に従ってください。

For safety, do not connect the connector for periph-

eral device wiring that might have excessive volt-

age to the following port.

: (LAN) connector

Follow the instructions for the above port.

本機をラックに設置するとき

熱の適切な排気・発散を得るために，ラックと本機の

間には，以下の空間を確保してください。

.上面 4cm 以上

.左右両側面 4cm 以上

.後面 10cm 以上

For kundene i Norge

Dette utstyret kan kobles til et IT-strømfordelingssystem.

設置時には，通気やサービス性を考慮して設置スペース

を確保してください。

.ファンの排気部や通気孔（BIN パネルの取っ手内）を

ふさがない。

.通気のために，セット周辺に空間をあける。

.作業エリアを確保するため，セット後方は，40cm 以

上の空間をあける。

机上などの平面に設置する場合は，左側面および右側面

は 4cm 以上の空間をそれぞれ確保してください。た

だし，セット上部はサービス性を考慮し 40cm 以上の

空間を確保することを推奨します。

XDJ-1000 1 (P)

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

conﬁrm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the speciﬁed limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please

make sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

5. Install the equipment while taking the operating

temperature of the equipment into consideration

For the operating temperature of the equipment, refer

to the speciﬁcations of the Operation Manual.

6. When performing the installation, keep the fol-

lowing space away from walls in order to obtain

proper exhaust and radiation of heat.

Top: 4 cm (1.6 inches) or more

Right, Left: 4 cm (1.6 inches) or more

Rear: 10 cm (4 inches) or more

Laser Diode Properties

Wavelength: 400 to 410 nm

Emission duration: Continuous

Laser output power: 280 mW (max. of

pulse peak), 150 mW (max. of CW)

Standard:

This XDJ-1000 are classiﬁed as a CLASS 1

LASER PRODUCT.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

This label is located on the top cover of the drive unit.

When installing the installation space must be secured

in consideration of the ventilation and service operation.

.Do not block the ventilation slots at the inside of

handles on the BIN panels, and vents of the fans.

.Leave a space around the unit for ventilation.

.Leave more than 40 cm of space in the rear of the unit

to secure the operation area.

When the unit is installed on the desk or the like, leave

at least 4 cm of space in the left and right sides.

Leaving 40 cm or more of space above the unit is

recommended for service operation.

1 (E)

XDJ-1000

Table of Contents

Manual Structure

Purpose of this manual............................................................ 3 (E)

Related manuals...................................................................... 3 (E)

1. Installation

1-1. Overview of Installation............................................1-1 (E)

1-1-1. Cautions before Installation.............................1-1 (E)

1-1-2. Supplied Accessories .......................................1-2 (E)

1-2. Installation Procedure................................................ 1-2 (E)

1-3. Operating Conditions ................................................1-3 (E)

1-4. Power Supply ............................................................1-3 (E)

1-4-1. Voltage and Power Requirements....................1-3 (E)

1-4-2. Recommended Power Cord .............................1-3 (E)

1-5. Installation Space ......................................................1-4 (E)

1-6. Installation of XDBK-J102 .......................................1-5 (E)

1-7. Removal/Installation of Shipping Screw and

Shipping Bracket.......................................................1-6 (E)

1-7-1. Carrier Shipping Screw.................................... 1-6 (E)

1-7-2. Removal of BIN Tray Shipping Bracket..........1-6 (E)

1-7-3. Installing the BIN Tray Shipping Bracket .......1-7 (E)

1-8. Installing the RFID (Option).....................................1-9 (E)

1-9. Rack Mounting........................................................ 1-10 (E)

1-10. Connectors/Cables...................................................1-15 (E)

1-11. Signal Inputs and Outputs ....................................... 1-15 (E)

1-12. Setting after Installation .......................................... 1-16 (E)

1-12-1. Tools...............................................................1-16 (E)

1-12-2. Procedure .......................................................1-16 (E)

1-13. Precautions for Relocation ...................................... 1-18 (E)

3 (E)

XDJ-1000

Manual Structure

Purpose of this manual

This manual is the installation manual of Professional Disc Library XDJ-1000 and

Professional Disc Drive XDBK-J102.

This manual is intended for use by trained system and service engineers,

and provides the information that is required to install (operating environment,

installation space, connection information, etc.).

For the installation of the Optional Power Supply XDBK-101, refer to the Installa-

tion Manual supplied with XDBK-101.

Related manuals

Besides this Installation Manual, the following manuals are prepared for this unit.

.Operation Manual (PDF) (Supplied with this unit.)

This manual describes the application and operation of this unit.

.Maintenance Manual (Available on request)

This manual describes the maintenance and service information (service overview,

error message, maintenance mode, periodic check, replacement of main parts, de-

tailed parts list, block diagrams, board layouts, schematic diagrams, etc.) for this

unit.

.XDBK-101 Installation Manual (Supplied with XDBK-101)

This manual describes the installation of the Optional Power Supply XDBK-101.

1-1 (E)

XDJ-1000

Section 1

Installation

1-1. Overview of Installation

1-1-1. Cautions before Installation

The Hard Disk Drives (HDD) are installed in this unit. The HDD is a precision part. The causes such as

shock, vibration and static electricity to the unit, and the conditions of temperature and humidity may

damage HDD or its data.

Before installation, read fully the following cautions, and perform the installation with extra care.

Cautions about shock and vibration

When transporting and moving

.Pack the unit using the packaging materials speciﬁed by the manufacturer.

.Use a proper cart.

.Avoid rough routes, and manage the cart gently.

When placing on a ﬂoor or table

.Put the unit on stable and horizontal place.

.Do not place the unit near vibrating equipments.

For the unit

.Never hit the unit, and drop the tool on the unit.

Take extra care

.Never give vibration or shock to the unit while the power is turned on, or within about 30 seconds after

turning off the power.

Cautions about rack mounting the unit

.Never give shock to all the rack mounted unit which has a HDD.

Caution about static electricity

.Keep static-producing items such as plastics (air caps or others) away from the working area.

.When touching the HDD unit, be sure to wear a grounded earth-band to protect against static electricity.

Cautions about temperature and humidity

.Temperature and humidity of storage and operating condition must be kept within the correct speciﬁed

range.

.Never turn on the power with the cabinet is removed in consideration of the air-cooling effect.

Cautions when an error appears in a HDD

.Treat this unit conform to the above cautions, even when an error appeared.

.Keep the unit in the condition in which the error appeared, and record the details of the error.

1-2 (E) XDJ-1000

1-1-2. Supplied Accessories

.Operation manual (Japanese/English/Chinese)

.Installation manual (This manual)

.RFID tag (30 sheets)

1-2. Installation Procedure

Installation procedure of this unit is shown on the following ﬂowchart.

Refer to each section about detail of each ﬂow.

The operation manual is also required to do *-marked ﬂow.

Start

Determination of

installation place

1-3. Operating Conditions

1-4. Power Supply

1-10. Connectors/Cables

1-11. Signal Inputs and Outputs

1-5. Installation Space

1-12. Settings after Installation

Note

Do not reuse the packing materials.

Unpacking

Installation

*Connection

*Initial setup

*Operation check

End

1-6. Installation of XDBK-J102

1-7. Removal of Shipping Screw and Shipping Bracket

1-8. Installing the RFID (Option)

1-9. Rack Mounting

Start

Determination of

installation place

1-3. Operating Conditions

1-4. Power Supply

1-10. Connectors/Cables

1-11. Signal Inputs and Outputs

1-5. Installation Space

1-12. Settings after Installation

Note

Do not reuse the packing materials.

Unpacking

Installation

*Connection

*Initial setup

*Operation check

End

1-6. Installation of XDBK-J102

1-7. Removal of Shipping Screw and Shipping Bracket

1-8. Installing the RFID (Option)

1-9. Rack Mounting

Andere Handbücher für XDCAM XDJ-1000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Lagerung Handbücher

Sony

Sony MSH-128 Bedienungsanleitung

Sony

Sony IJ1001M Bedienungsanleitung

Sony

Sony VAIO VGP-UHDM08 Bedienungsanleitung

Sony

Sony HDD PlayStation 2 Bedienungsanleitung

Sony

Sony MSH-128S2 Bedienungsanleitung

Sony

Sony PHU-60K Series Bedienungsanleitung

Sony

Sony MicroVault USM1GH Bedienungsanleitung

Sony

Sony Microdrive RHMD2G Bedienungsanleitung

Sony

Sony HDPS-M10 - Data Storage Wallet Bedienungsanleitung

Sony

Sony AIT TSL-SA300C Bedienungsanleitung

Sony

Sony IJ1001SNBT Bedienungsanleitung

Sony

Sony SCPH-20401 Bedienungsanleitung

Sony

Sony USM128B Bedienungsanleitung

Sony

Sony SDT-9000 Series Bedienungsanleitung

Sony

Sony MSX-2GS Bedienungsanleitung

Sony

Sony MSFD-20U Bedienungsanleitung

Sony

Sony USM128DS Bedienungsanleitung

Sony

Sony SDX-D250V Handbuch

Sony

Sony DMS-8800B Bedienungsanleitung

Sony

Sony HDPS-M1 Bedienungsanleitung

Sony

Sony VAIO VGP-UHDP04 Bedienungsanleitung

Sony

Sony HD-EG5U Bedienungsanleitung

Sony

Sony SDX-S500C Handbuch

Sony

Sony 7819900133 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung