Sony HDS-X5800 Bedienungsanleitung

ROUTING SWITCHER PROCESSOR

HDS-X5800

33 INPUT BOARD SET

HKS-5810M

HKS-5810SD

34 CASCADE INPUT BOARD SET

HKS-5811M

HKS-5811SD

33 INPUT DISTRIBUTION BOARD

HKS-5820M

264 x34 MATRIX BOARD

HKS-5830M

HKS-5830SD

34 OUTPUT BOARD SET

HKS-5860M

HKS-5860SD

INSTALLATION MANUAL

1st Edition (Revised 2)

HDS-X5800

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

HDS-X5800 Serial No. 10001 and Higher

HKS-5810M Serial No. 10001 and Higher

HKS-5810SD Serial No. 10001 and Higher

HKS-5811M Serial No. 10001 and Higher

HKS-5811SD Serial No. 10001 and Higher

HKS-5820M Serial No. 10001 and Higher

HKS-5830M Serial No. 10001 and Higher

HKS-5830SD Serial No. 10001 and Higher

HKS-5860M Serial No. 10001 and Higher

HKS-5860SD Serial No. 10001 and Higher

HDS-X5800 1 (P)

Attention-when the product is installed in Rack:

(For HDS-X5800)

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

5. Install the equipment while taking the operating

temperature of the equipment into consideration

For the operating temperature of the equipment, refer

to the specifications of the Operation Manual.

6. When performing the installation, keep the rear of

the unit 10 cm (4 inches) or more away from walls

in order to obtain proper exhaust and radiation of

heat.

When using a LAN cable:

For safety,do not connect to the connector for

peripheral device wiring that might have excessive

voltage.

For the customers in the Netherlands

Voor de klanten in Nederland

Hoe u de batterijen moet verwijderen, leest u in de

Onderhoudshandleiding.

Gooi de batterij niet weg maar lever deze in als klein

chemisch afval (KCA).

Für Kunden in Deutschland

Entsorgungshinweis: Bitte werfen Sie nur entladene

Batterien in die Sammelboxen beim Handel oder den

Kommunen. Entladen sind Batterien in der Regel dann,

wenn das Gerät abschaltet und signalisiert “Batterie

leer”oder nach längerer Gebrauchsdauer der Batterien

“nicht mehr einwandfrei funktioniert”. Um

sicherzugehen, kleben Sie die Batteriepole z.B. mit

einem Klebestreifen ab oder geben Sie die Batterien

einzeln in einen Plastikbeutel.

1 (E)

HDS-X5800

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 3 (E)

Related manuals................................................................................................... 3 (E)

Contents ............................................................................................................... 4 (E)

Trademarks .......................................................................................................... 4 (E)

1. Installation

1-1. Installation Procedure............................................................................ 1-1 (E)

1-2. Operating Environment ......................................................................... 1-2 (E)

1-3. Power Supply ........................................................................................ 1-2 (E)

1-3-1. Power Specifications ............................................................ 1-2 (E)

1-3-2. Power Cord ........................................................................... 1-2 (E)

1-4. Installation Space .................................................................................. 1-3 (E)

1-5. Rack Mounting ...................................................................................... 1-4 (E)

1-5-1. Precautions for Rack Mounting ...........................................1-4 (E)

1-5-2. Rack Mounting Procedure .................................................... 1-5 (E)

1-6. Installation of Optional Boards ............................................................. 1-7 (E)

1-6-1. Table of Optional Boards ..................................................... 1-7 (E)

1-6-2. List of Installation Slots ....................................................... 1-7 (E)

1-6-3. Installation/Removal of Plug-in Boards ............................... 1-8 (E)

1-6-4. Installation/Removal of Connector Boards ........................ 1-10 (E)

1-7. Matching Connectors and Cables........................................................ 1-12 (E)

1-8. Input and Output Signals of Connectors ............................................. 1-13 (E)

1-9. System Connection.............................................................................. 1-14 (E)

1-9-1. S-BUS Data Link ............................................................... 1-14 (E)

1-10. How to Extend Inputs and Outputs ..................................................... 1-16 (E)

1-10-1. Equipment Required for System Extension ....................... 1-16 (E)

1-10-2. How to Configure Optional Boards ................................... 1-18 (E)

1-10-3. Cascade Connection Example ............................................ 1-19 (E)

1-10-4. Output Extension Example ................................................ 1-20 (E)

1-10-5. Input/Output Extension Example ....................................... 1-21 (E)

1-10-6. Control System Connection Example and Setup ............... 1-22 (E)

2 (E) HDS-X5800

1-11. Setting the On-Board Switches and Description of LEDs ..................1-23 (E)

1-11-1. CPU-339 Board (HDS-X5800) .......................................... 1-23 (E)

1-11-2. MX-103 Board (HKS-5830M) ...........................................1-30 (E)

1-11-3. MX-104 Board (HKS-5830SD) ......................................... 1-32 (E)

1-11-4. IPM-98 Board (HKS-5820M) ............................................ 1-32 (E)

1-11-5. EQ-91 Board (HKS-5811M) .............................................. 1-33 (E)

1-11-6. EQ-92 Board (HKS-5811SD) ............................................ 1-33 (E)

1-11-7. FP-129 Board (HDS-X5800) ............................................. 1-34 (E)

1-11-8. CNI-11 Board (HKS-5810M) ............................................ 1-38 (E)

1-11-9. CNI-12 Board (HKS-5810M) ............................................ 1-38 (E)

1-11-10. CNI-13 Board (HKS-5810SD) ...........................................1-38 (E)

1-11-11. CNI-14 Board (HKS-5810SD) ...........................................1-39 (E)

1-11-12. CNO-13 Board (HKS-5860M) ...........................................1-39 (E)

1-11-13. CNO-14 Board (HKS-5860M) ...........................................1-39 (E)

1-11-14. CNO-15 Board (HKS-5860SD) ......................................... 1-40 (E)

1-11-15. CNO-16 Board (HKS-5860SD) ......................................... 1-40 (E)

1-11-16. SPG-16 Board (HDS-X5800) ............................................ 1-40 (E)

1-11-17. RM-192 Board (HDS-X5800) ............................................ 1-41 (E)

1-11-18. TR-127 Board (HDS-X5800) ............................................. 1-41 (E)

1-12. Setting IP Address ...............................................................................1-42 (E)

2. Service Overview

2-1. Main Parts Location .............................................................................. 2-1 (E)

2-2. Removing/Installing the Front Panel .................................................... 2-4 (E)

2-3. Error Indication ..................................................................................... 2-5 (E)

2-3-1. Error Number Display on the CPU-339 Board .................... 2-5 (E)

2-3-2. Front Panel Status Indication (LE-251/FP-129 Board) ........2-6 (E)

2-4. Cleaning Filter ..................................................................................... 2-12 (E)

2-5. CPU Battery ........................................................................................ 2-12 (E)

2-6. Data Backup ........................................................................................ 2-13 (E)

2-6-1. Connection ......................................................................... 2-13 (E)

2-6-2. Installing BZR-20 ............................................................... 2-14 (E)

2-6-3. Uploading Data .................................................................. 2-15 (E)

2-6-4. Downloading Data .............................................................2-16 (E)

3 (E)

HDS-X5800

Purpose of this manual

This manual is the installation manual of Routing Switcher Processor HDS-X5800

and the optional boards.

This manual is intended for use by trained system and service engineers, and

describes the information on installing the HDS-X5800.

Related manuals

Besides this Installation Manual, the following manuals are prepared for HDS-

X5800 and the optional boards.

.Operation Manual (Supplied with HDS-X5800)

This manual describes the application and operation of HDS-X5800.

.System Setup Manual (Supplied with HDS-X5800)

This manual describes the software initialization or operation confirmation.

.e-Manual (Tentative name) (Available on request)

This electronic manual intended for use by trained system and service engineers

describes detailed parts list, block diagrams, schematic diagrams, and board layouts

required for parts-level service.

For obtaining, contact your local Sony Sales Office/Service Center.

.Protocol Manual (Available on request)

This manual describes the protocol for controlling this unit.

The manual below is provided for the protocol that this unit can support.

If this manual is required, please contact your local Sony Sales Office/Service Center.

S-BUS PROTOCOL AND COMMAND SPECIFICATIONS

(S-BUS remote terminal control protocol)

Part No.: 9-977-477-1X

.“Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in B&P Company equipment.

Semiconductors that cannot be searched for on this CD-ROM are listed in the

maintenance manual for the corresponding unit. The maintenance manual contains

a complete list of all semiconductors and their ID Nos., and thus should be used

together with the CD-ROM.

Part number: 9-968-546-XX

Manual Structure

4 (E) HDS-X5800

Contents

The following is a summary of all the sections of this manual.

Section 1 Installation

This section describes the operating environment, power supply, installation space,

rack mounting, installation of optional boards, connectors, input and output signals

of connectors, system connection, extension of inputs/outputs and on-board switch/

LED.

Section 2 Service Overview

This section describes the location of main parts, error indication, data backup.

Trademarks

Trademarks and registered trademarks used in this manual are follows.

.Ethernet is a registered trademark of Xerox Corporation.

.IBM and AT are registered trademarks of International Business Machines

Corporation.

.Pentium is a registered trademark of Intel Corporation.

.Windows is a registered trademark of Microsoft Corporation.

1-1 (E)

HDS-X5800

Section 1

Installation

1-1. Installation Procedure

The following chart shows the procedure for installing the unit.

For details of the following chart, refer to the relevant section or related manual.

Start

Selection of installation

place

Rack mounting

Installation of optional

boards

Connection

Setting the On-Board

Switches

1-2.

1-3.

1-4.

1-5.

1-6.

1-7.

1-8.

1-9.

1-10.

1-11.

Operating Environment

Power Supply

Installation Space

Rack Mounting

Installation of Optional Boards

Matching Connectors and Cables

Input and Output Signals of Connectors

System Connection

How to Extend Inputs and Outputs

Setting the On-Board Switches and

Description of LEDs

End

System Setup Manual

Initial setting

Operation check

1-2 (E) HDS-X5800

1-2. Operating Environment

Do not install the unit in a place subject to excessive oil

vapor, steam, moisture, or dust, otherwise a fire or electric

shock may result.

.To prevent the temperature rising inside the unit, ensure

there is adequate circulation of air near where the unit is

installed. Never block the ventilation holes.

.Never install the unit near a heat source.

Operating temperature : 5 dC to 40 dC

Storage temperature : _20 dC to +60 dC

Operating humidity : 10% to 90% (no condensation)

1-3. Power Supply

The HDS-X5800 contains the four power supply units as

the standard installation.

The units A1 and B1, and the units A2 and B2 back up the

two power line systems respectively. Therefore, turn on all

of the four power supply units when using the HDS-

X5800.

(Refer to Section 2-1 for the location of the power supply

units.)

1-3-1. Power Specifications

Power requirements AC 100 to 240 V ±10%

Power frequency 50/60 Hz

Current consumption AC100 V : 12 A (max.)

AC240 V : 4 A (max.)

Inrush current

At power voltage of 100 V : 60 A

(Maximum when all of the four

power supply units are turned on)

At power voltage of 240 V : 85 A

(Maximum when all of the four

power supply units are turned on)

Power consumption 1200 VA (max.)

The capacity of the AC power must be commensurate with

the inrush current. If the capacity of the AC power is not

sufficiently large, the breaker of the AC power on the

supply side will trip or the unit will not operate normally.

1-3-2. Power Cord

The power cords are not supplied with the unit. Be sure to

use power cords that are suitable for the place of operation.

For the customer outside of the area as shown above,

please contact your local Sony Sales Office/Service

Center.

1-2. Operating Environment

1-3. Power Supply

For customers in the U.S.A. and Canada

1Power cord, 125 V 10 A (2.4 m) : !1-557-377-11

2Plug holder (Black) : 2-990-242-01

AC inlet

For customers in the United Kingdom

1Power cord, 250 V 10 A (2.4 m) : !1-782-165-11

2Plug holder (Brown) : 3-613-640-01

1AC inlet

For customers in European countries except the United Kingdom

1Power cord, 250 V 10 A (2.0 m) : !1-551-631-22

2Plug holder (Brown) : 3-613-640-01

AC inlet

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Schalten Handbücher

Sony

Sony DMX-SW1 - Bravia Input Link Bedienungsanleitung

Sony

Sony CAV-CVS12ES - Component Video Switcher Bedienungsanleitung

Sony

Sony PVS-R102 Bedienungsanleitung

Sony

Sony BRS-200 Bedienungsanleitung

Sony

Sony DVS-7200 Bedienungsanleitung

Sony

Sony MVS-8000 Bedienungsanleitung

Sony

Sony XVS-G1 Bedienungsanleitung

Sony

Sony UH-1000 Bedienungsanleitung

Sony

Sony XVS-9000-C Bedienungsanleitung

Sony

Sony ESBK-7052 Bedienungsanleitung

Sony

Sony DVS-7200A Bedienungsanleitung

Sony

Sony DVS-2000C Bedienungsanleitung

Sony

Sony XVS-G1 Bedienungsanleitung

Sony

Sony DVS-9000 Bedienungsanleitung

Sony

Sony MVS-8000 Bedienungsanleitung

Sony

Sony DFS-700 Bedienungsanleitung

Sony

Sony MVS-8000X-C Bedienungsanleitung

Sony

Sony MVS-8000X System Bedienungsanleitung

Sony

Sony BVS-A3232 Bedienungsanleitung

Sony

Sony MVS-8000 Bedienungsanleitung

Sony

Sony CCP-8000 Series Bedienungsanleitung

Sony

Sony DVS-9000 Bedienungsanleitung

Sony

Sony MVS-8000X System Bedienungsanleitung

Sony

Sony MVS-8000 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung