Sony KD-28DX50 U Bedienungsanleitung

4-096-786-11

KD-28DX50 U

KD-32DX50 U

Operating Instructions

Before operating the TV, please read the ‘Safety Information’ section of this

manual. Retain this manual for future reference.

Trinitron

Integrated Digital

Television

409678611

2832DX50U.book Page 1 Monday, July 14, 2003 10:35 AM

Thank you for choosing this

FD Trinitron Integrated

Digital Television

Before operating the TV, please read this instruction

manual thoroughly and retain it for future reference.

All instructions in this manual refer to buttons on the

supplied remote control unless stated otherwise.

The model and serial numbers are located on the back

of the TV. Record the serial number in the space

provided below. Refer to these numbers whenever

you call your dealer regarding this product.

Model No. KD-28DX50U / KD-32DX50U

Serial No. ______________

Please note: The information in this manual was correct at the time of

going to print. However, some minor changes may have been made late

in the product’s development. All illustrations in this manual have been

created during the product’s development and may differ slightly to the

finished product.

CAUTION- TO PREVENT ELECTRIC SHOCK,

DON'T REMOVE COVER. FOR QUALIFIED

SERVICE PERSONNEL ONLY.

MODEL NO.

KD-28DX50U

TRINITRON DIGITAL TV

220-240V 50Hz

SER.NO.

MADE IN U.K.

BEAB

Approved

6000001

Serial No.

CAUTION- TO PREVENT ELECTRIC SHOCK,

DON'T REMOVE COVER. FOR QUALIFIED

SERVICE PERSONNEL ONLY.

MODEL NO.

KD-32DX50U

TRINITRON DIGITAL TV

220-240V 50Hz

SER.NO.

MADE IN U.K.

BEAB

Approved

6000001

Serial No.

2832DX50U.book Page 2 Monday, July 14, 2003 10:35 AM

Table of Contents

Table of Contents 1

Table of Contents

Safety Information

Notice for customers in the United Kingdom . . . . . . . . . . . . . . . . . . . . 2

Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Getting Started

Checking the accessories supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Inserting batteries into the remote control . . . . . . . . . . . . . . . . . . . . . . 4

Connecting an aerial and VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Switching on the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Automatically tuning the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Switching between digital and analogue mode . . . . . . . . . . . . . . . . . . 6

Adjusting the Brightness, Colour and Sharpness settings . . . . . . . . . . 7

Adjusting the sound settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Basic Operation

Overview of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Overview of the TV buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Everyday use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Digital Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Analogue Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Advanced Operation

The Channel Index menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

The Digital Electronic Programme Guide (EPG) . . . . . . . . . . . . . . . . . 16

The Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

The Main menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Detail Set-up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Using the TV menu system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Picture Adjustment menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Sound Adjustment menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Timer menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Set Up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Manual Programme Preset menu . . . . . . . . . . . . . . . . . . . . . . . . . 23

Detail Set Up menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Connecting Other Equipment

Overview of the rear sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Overview of the front sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Connecting other equipment to the TV. . . . . . . . . . . . . . . . . . . . . . . . . 28

Viewing pictures from a connected VCR . . . . . . . . . . . . . . . . . . . . . . . 28

Viewing pictures from equipment connected to the rear sockets . . . . . 28

Viewing pictures from equipment connected to the front sockets . . . . 28

Remote control of other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Programming the remote control. . . . . . . . . . . . . . . . . . . . . . . . . . 29

Controlling a DVD player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Controlling a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Additional Information

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

How to lift the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

2832DX50U.book Page 1 Monday, July 14, 2003 10:35 AM

Safety Information

2Safety Information

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI

to BS 1362 (i.e. marked with or ) must be used. When an alternative type of plug is used it

should be fitted with a 5 AMP fuse, otherwise the circuit should be protected by a 5 AMP fuse at

the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure

to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service centre.

How to replace the Fuse

Open the fuse compartment with a flat blade screwdriver, and replace the fuse.

IMPORTANT

If the plug supplied is not suitable for the socket outlet in your home, it should be cut off and an

appropriate plug fitted in accordance with the following instructions:

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter

N or coloured black. The wire which is coloured brown must be connected to the terminal which is

marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug

which is marked by the letter E or by the safety earth symbol Ior coloured green or green and

yellow.

WARNING

• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet.

This plug cannot be used and should be destroyed.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing

to qualified personnel only.

ASA

FUSE

2832DX50U.book Page 2 Monday, July 14, 2003 10:35 AM

Safety Information

Safety Information 3

This set is to operate on a 220-240V AC

supply only. Take care not to connect too

many appliances to the same power socket

as this could result in fire or electric shock.

For environmental and safety reasons, it is

recommended that the TV is not left if

standby when unused. Disconnect from the

mains. However, some TVs may have

features which need the TV to be left in

standby to work correctly. The instructions

in this manual will inform you if this applies.

Never push objects of any kind into the set

as this could result in a fire or electric shock.

Never spill liquid of any kind on the set. If

any liquid or solid object does fall through,

do not operate the TV. Have it checked

immediately by qualified personnel.

Do not open the cabinet and the rear cover

of the TV. Refer to qualified service

personnel only.

To prevent fire or shock hazard, do not

expose the TV to rain or moisture.

For your own safety, do not touch any part

of the TV, power lead or aerial lead during

lightning storms.

Do not cover the ventilation openings of the

TV. For ventilation, leave a space of at least

10cm all around the set.

Never place the TV in hot, humid or

excessively dusty places. Do not install the

TV where it may be exposed to mechanical

vibrations.

Clean the screen and cabinet with a soft,

lightly dampened cloth. Do not use any type

of abrasive pad, alkaline cleaner, scouring

powder or solvent, such as alcohol or

benzine, or antistatic spray. As a safety

precaution, unplug the TV before cleaning it.

Pull out the power lead by the plug. Do not

pull on the power lead itself.

Take care not to place heavy objects on the

power lead as this could result in damage.

We recommend you wind any excess lead

around the holders provided on the rear of

the TV.

Unplug the power lead before moving the

TV. Avoid uneven surfaces, quick steps or

excessive force. If the set has been

dropped or damaged, have it checked

immediately by qualified service personnel.

Do not cover the ventilation openings of the

TV with items such as curtains or

newspapers etc.

Do not place any objects on the TV. To

prevent fire, keep inflammable objects or

naked lights (e.g. candles) away from the TV.

Place the TV on a secure stable stand. Never

attempt to move the TV and stand together -

always move the TV and stand separately.

Do not place the TV on its side or face up. Do

not allow children to climb on to it.

Due to the unique floating design of this TV, highly recommend you use their

designated stand SU-28DX50 for KD-28DX50U and SU-32DX50 for KD-32DX50U.

2832DX50U.book Page 3 Monday, July 14, 2003 10:35 AM

Getting Started

4Getting Started

Follow steps 1 - 8 to install the TV and view programmes

Check that you have the following items:

Always remember to:

•observe the correct polarity when inserting batteries,

•dispose of batteries in an environmentally friendly way.

Batteries

Checking the supplied accessories

Inserting batteries into the remote control

RF lead

Remote control

VIDEO

DIGITAL

2832DX50U.book Page 4 Monday, July 14, 2003 10:35 AM

Basic Operation

Basic Operation 5

1. Connect the TV plug to your mains socket

(220 - 240V AV, 50Hz)

2. Push in the On/Off button (labelled !) on the front

of the TV.

z If the red standby mode indicator on the front of the TV is

lit, press the TV I/1button on the remote control to switch

on the set. Please be patient as the picture may take a

few moments to appear on the TV screen.

Switching on the TV

Connecting an aerial only

1. Connect your aerial lead to the socket labelled 1

on the rear of the TV.

2. Connect the supplied RF lead from the socket

labelled on the rear of the TV to the socket

labelled IN* on your VCR.

3. Connect an RF lead from the socket labelled OUT*

on your VCR to the socket labelled 2on the rear

of the TV.

4. Connect a fully wired 21-pin scart lead from the

socket labelled i2/ron the rear of the TV to the

socket labelled TV* on your VCR**

5. Insert a pre-recorded tape into the VCR and press

the ‘PLAY’ button. This enables the TV to locate

and store the video channel during the

‘Automatically tuning the TV’ procedure.

z*Socket names may vary depending on make and model

of VCR. Refer to your VCR instruction manual for details.

**If your VCR does not have a scart socket follow the

connecting instructions above ignoring the scart lead

connection.

1. Connect your aerial lead to the socket labelled 1

on the rear of the TV.

2. Connect the supplied RF lead from the sockets

labelled and 2on the rear of the TV.

Connecting an aerial and VCR

Rear of TV.

Supplied RF lead

Scart lead

(not supplied)

Supplied

RF lead

Rear of TV.

On/Off button

2832DX50U.book Page 5 Monday, July 14, 2003 10:35 AM

Getting Started

6Getting Started

1. When you switch on the TV for the first time a menu appears on the

screen asking you to check if the picture is slanted. (Sometimes the

Earth’s natural magnetism can cause the screen to look slanted.)

a) If no correction is required, press the Vor vbutton to highlight ‘Not

necessary’. Press the OK button to continue.

b) If some correction is required, press the Vor vbutton to highlight

‘Adjust now’. Press the OK button to continue. Press the Vor vbutton

to correct the slant. Press the OK button to store.

2. The autotune prompt appears. Press the OK button to select ‘Yes’. The

autotune procedure begins.

The digital autotune display appears on screen and the TV starts to

search for all the available digital channels. This may take some time,

please be patient and do not press any buttons on the TV or remote

control.

If no digital or analogue channels are found, a message appears asking

you to confirm that the aerial is connected correctly. Check all the aerial

connections and press the OK button to start the autotune procedure

again.

When the digital autotune is complete, the analogue autotune starts to

search for all the available analogue channels.

Once all available digital and analogue channels have been stored, the

TV returns to normal operation, displaying the digital channel stored on

channel number 1. If no digital channels are found, the analogue channel

stored on channel 1 is displayed.

The TV has now tuned

in all the available channels

1. Press the DIGITAL/abutton to switch between digital and analogue

mode.

In digital mode, an information banner appears briefly on screen when

the channel is changed.

In analogue mode, the channel number appears in green lettering when

the channel is changed.

Automatically tuning the TV

Switching between digital and analogue mode

The ‘Picture Rotation’ menu.

The ‘Autotune’ prompt.

Do you want to start

automatic tuning?

Ye s

If picture slants, please

adjust picture rotation

Not necessary

Adjust now

2832DX50U.book Page 6 Monday, July 14, 2003 10:35 AM

Getting Started

Getting Started 7

This TV has three picture mode settings, ‘Live’, ‘Movie’and ‘Personal’. ‘Live’and

‘Movie’are preset and only the ‘Contrast’setting can be adjusted. ‘Personal’mode

however, also allows you to adjust the ‘Brightness’, ‘Colour’and ‘Sharpness’

settings.

This TV has four sound mode settings, ‘Personal’, ‘Rock*, ‘Pop, and ‘Jazz’.

1. Press the MENU button on the remote control to display the TV menu

system on the TV screen.

2. Press the bbutton to enter the ‘Picture Adjustment’menu.

3. The ‘Mode’option is highlighted. Press the bbutton.

4. Press the Vor vbutton to highlight ‘Live’, ‘Movie’or ‘Personal’. Press the

OK button to confirm.

5. a) If you have selected ‘Live’ or ‘Movie’:

Go to step 6.

b) If you have selected ‘Personal’:

You can now adjust the ‘Brightness’, ‘Colour’and ‘Sharpness’settings.

(Sharpness is not adjustable in digital mode).

Press the Vor vbutton to highlight ‘Brightness’, ‘Colour’or ‘Sharpness’.

Press the bbutton. Press the Bor bbutton to adjust the setting. Press

the OK button to store.

6. Press the MENU button to exit the TV menu system and return to normal

TV operation.

1. Press the MENU button on the remote control to display the TV menu

system on the TV screen.

2. Press the vbutton to select the ‘Sound Adjustment’menu.

3. Press the bbutton to enter the ‘Sound Adjustment’menu.

4. The ‘Mode’option is highlighted. Press the bbutton.

5. Press the Vor vbutton to highlight ‘Personal’, ‘Rock’, ‘Pop’or ‘Jazz’.

Press the OK button to confirm.

6. a) If you have selected ‘Rock’, ‘Pop’ or ‘Jazz’:

Go to step 7.

b) If you have selected ‘Personal’:

You can now adjust the ‘Tr e ble ’and ‘Bass’settings.

Press the Vor vbutton to highlight ‘Tr e bl e ’or ‘Bass’. Press the bbutton.

Press the Bor bbutton to adjust the setting. Press the OK button to store.

7. Press the MENU button to exit the TV menu system and return to normal

TV operation.

Adjusting the Brightness, Colour and Sharpness settings

Adjusting the sound

The ‘Picture Adjustment’menu.

The ‘Sound Adjustment’menu.

Picture Adjustment

Mode: Personal

Contrast

Brightness

Colour

Sharpness

Hue

Reset

Sound Adjustment

Mode: Personal

Treble

Bass

Balance

Reset

Dual Sound: Stereo

Detail Adjustment

2832DX50U.book Page 7 Monday, July 14, 2003 10:35 AM

Basic Operation

8Basic Operation

Overview of the remote control

VIDEO

DIGITAL

1VIDEO I/1- VCR/DVD Standby button

Press to switch off your VCR/DVD player temporarily. Press again to return

to normal operation.

2TV I/1- TV Standby button

Press to switch off the TV temporarily. The red standby indicator on the front

of the TV is lit. Press again to return to normal operation.

3- Screen Mode button

Press to change the screen mode. Refer to page 11.

4DIGITAL/a- Digital/Analogue mode, TV button

In TV mode: Press to switch between digital and analogue mode.

In analogue text, video input mode, TV menu system, INFO menu, EPG and

Channel Index menu: Press to return to normal TV operation.

5/ -Input Select/Text Hold button

In TV mode: Press to view signals from equipment connected to the TV

sockets. Refer to page 28.

In analogue text mode: Press to hold the current page. Refer to page 14.

6Numbered buttons

In TV mode: Press to select the required channel number. For channel

numbers 10 and above, enter the second digit within two seconds.

In analogue text mode: Press to enter the three digital page number. Refer

to page 14.

7/ -INFO/Text Reveal button

In digital TV mode: Press to access the Info menu. Refer to page 13.

In analogue TV mode: Press to display information such as current channel

number and screen mode.

In analogue text mode: Press to reveal concealed information (e.g. answers

to a quiz). Refer to page 14.

8- Previous channel button

In TV mode: Press to return to the previous channel watched (provided that

the channel was watched for more than five seconds).

9Coloured buttons

In digital menu systems: Press to select the options at the bottom of the

screen in the Info, Main, Channel Index and EPG digital menus.

In analogue text mode: Press to use Fastext. Refer to page 14.

q; - EPG button

In digital TV mode: Press to access the Digital Electronic Programme Guide

(EPG). Refer to page 16.

qa /- Text button

In digital TV mode: Press to access digital text. Refer to page 13.

In analogue TV mode: Press to access analogue text. Refer to page 14.

qs V, v, Band bbuttons

In TV menu system: Press to move through the options. Refer to page 21.

qd OK button

In TV menu system: Press to confirm a selection. Refer to page 21.

In digital TV mode: Press to access the Channel Index menu. Refer to

page 15.

In analogue TV mode: Press to access the Programme Index table. Press

the Vor vbutton to highlight an analogue channel. Press the bbutton to

display the chosen channel.

qf MENU button

Press to access the TV menu system. Refer to page 21.

qg •REC button

When Mode Selector button is set to ‘VCR’: Press to begin recording. Refer

to page 29.

qh Mode Selector button

This remote control can be programmed to operate the basic functions of

most DVD players and VCRs. Once programmed, press this button

repeatedly to select TV, VCR or DVD mode. Refer to page 29.

qj 2+/- Volume buttons

Press to increase (+) or decrease (-) the TV volume.

qk PROG +/- buttons

In TV mode: Press to view the next (+) or previous (-) channel.

In analogue text mode: Press to view the next (+) or previous (-) page. Refer

to page 14.

ql % - Mute button

Press to mute the TV sound. Press again to restore.

qj qk

2832DX50U.book Page 8 Monday, July 14, 2003 10:35 AM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Fernseher Handbücher

Sony

Sony KV-36XBR800 - 36" Trinitron Color Flat Tv Wega... Bedienungsanleitung

Sony

Sony KV-27FS120 - FD Trinitron WEGA Flat Screen... Bedienungsanleitung

Sony

Sony BRAVIA XBR-55X700D Bedienungsanleitung

Sony

Sony GRAND WEGA KF-50SX200K Bedienungsanleitung

Sony

Sony FD Trinitron KV-29LS40B Bedienungsanleitung

Sony

Sony Bravia KDL-48WD65x Bedienungsanleitung

Sony

Sony FD Trinitron WEGA KV-36FS100 Bedienungsanleitung

Sony

Sony TRINITRON KV-FA21M63 Bedienungsanleitung

Sony

Sony TRINITRON KV-G14L2J Bedienungsanleitung

Sony

Sony KV-SW34M61 Bedienungsanleitung

Sony

Sony XBR-49X800C Bedienungsanleitung

Sony

Sony TRINITRON KV-PF21M70 Bedienungsanleitung

Sony

Sony KV-30XBR910 Bedienungsanleitung

Sony

Sony KDL26E4000U Bedienungsanleitung

Sony

Sony FD Trinitron WEGA KV-27FS200 Bedienungsanleitung

Sony

Sony Trinitron Bedienungsanleitung

Sony

Sony WEGA KV-27FS100L Bedienungsanleitung

Sony

Sony TRINITRON KV-XF25N90 Bedienungsanleitung

Sony

Sony KV-29FA350 Bedienungsanleitung

Sony

Sony BRAVIA KD-85X9507G Bedienungsanleitung

Sony

Sony KDL-32BX353 Bedienungsanleitung

Sony

Sony TRINITRON KV-29FS105 Bedienungsanleitung

Sony

Sony KDF-E60A20PKG - 60" Lcd Projection Hd-tv Grand... Bedienungsanleitung

Sony

Sony KV-32XBR200 - 32" Fd Trinitron Wega Xbr Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Philips

Philips Colour Television Bedienungsanleitung

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung

Sylvania

Sylvania 6427FB Bedienungsanleitung