Sony SLV-478 Bedienungsanleitung

Video Cassette

Recorder

Operating Instructions

3-861-448-11 (1)

SLV-478

Introduction

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to

qualified personnel only.

CAUTION

To prevent electric shock, do not use this

polarized AC plug with an extension cord,

receptacle or other outlet unless the blades can

be fully inserted to prevent blade exposure.

Precautions

Safety

• Operate the unit only on 120 V AC, 60 Hz.

• If anything falls into the cabinet, unplug the

unit and have it checked by qualified

personnel before operating it any further.

• One blade of the plug is wider than the

other for the purpose of safety and will fit

into the power outlet only one way. If you

are unable to insert the plug fully into the

outlet, contact your Sony dealer.

• Unplug the unit from the wall outlet if you

do not intend to use it for an extended

period of time. To disconnect the cord, pull

it out by the plug, never by the cord.

Installing

• Allow adequate air circulation to prevent

internal heat buildup.

• Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials (curtains,

draperies) that may block the ventilation

slots.

• Do not install the unit near heat sources

such as radiators or air ducts, or in a place

subject to direct sunlight, excessive dust,

mechanical vibration or shock.

• Do not install the unit in an inclined

position. It is designed to be operated in a

horizontal position only.

• Keep the unit and cassettes away from

equipment with strong magnets, such as

microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to

a warm location, moisture may condense

inside the VCR and cause damage to the

video head and tape. When you first install

the unit, or when you move it from a cold to

a warm location, wait for about one hour

before operating the unit.

Caution

Television programs, films, video tapes and

other materials may be copyrighted.

Unauthorized recording of such material may

be contrary to the provisions of the copyright

laws. Also, use of this recorder with cable

television transmission may require

authorization from the cable television

transmission and/or program owner.

Introduction

Table of contents

Getting Started

4Step 1: Unpacking

5Step 2: Setting up the remote commander

7Step 3: Hookups

17 Selecting a language

18 Setting the clock

20 Presetting channels

Getting Started

Basic Operations

26 Playing a tape

28 Recording TV programs

31 Recording TV programs using the

timer

Additional Operations

34 Playing/searching at various

speeds

35 Recording TV programs using the

quick timer

36 Checking/changing/canceling

timer settings

38 Adjusting the picture

39 Changing menu options

40 Editing with another VCR

Additional Information

42 General setup information

44 Troubleshooting

46 Specifications

47 Index to parts and controls

51 Index

back cover

Quick reference to using the VCR

Getting Started6

Getting Started

Step 1

Unpacking

Check that you have received the following items with the VCR:

• Remote commander

• Size AA (R6) batteries

• 75-ohm coaxial cable with F-type

connectors

Getting Started

Inserting the batteries

Insert two size AA(R6) batteries by

matching the + and – on the

batteries to the diagram inside the

battery compartment.

Insert the negative (–) end first, then

push in and down until the positive

(+) end clicks into position.

Using the remote commander

You can use this remote

commander to operate this VCR

and a Sony TV. Buttons on the

remote commander marked with

a dot (•) can be used to operate

your Sony TV.

Step 2

Setting up the remote commander

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove

the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of batteries.

continued

To operate

the VCR

a Sony TV

Set TV / VIDEO to

VIDEO and point at the remote sensor on the VCR

TV and point at the remote sensor on the TV

Remote sensor

TV / VIDEO

123

Getting Started8

Step 2: Setting up the remote commander (continued)

Notes

• If the TV uses a different remote control system from the one programmed to work

with the VCR, you cannot control your TV with the remote commander.

• If you enter a new code number, the code number previously entered will be erased.

• When you replace the batteries of the remote commander, the code number

automatically resets to 01 (Sony). Reset the appropriate code number.

Code

number

03,08,12

04,13

04,12,13,17

04,12

06,19

03,04

06,18

05,14

Manufacturer

RCA

Sampo

Sanyo

Scott

Sears

Sharp

Sylvania

Teknika

Toshiba

Wards

Yorx

Zenith

Code

number

04,10

07,10,11

03,05,18

08,12

03,08,14

03,04,12

Manufacturer

Sony

Akai

AOC

Centurion

Coronado

Curis-Mathes

Daytron

Emerson

Fisher

General Electric

Gold Star

Hitachi

J.C.Penny

Code

number

03,04,14

06,10

03,04,17

02,03

04,12

Manufacturer

JVC

KMC

Magnavox

Marantz

MGA/Mitsubishi

NEC

Panasonic

Philco

Philips

Pioneer

Portland

Quasar

Radio Shack

Controlling other TVs with the remote commander

The remote commander is preprogrammed to control non-Sony TVs. If your

TV is listed in the table below, set the appropriate manufacturer’s code

number.

1Set TV / VIDEO at the top of the remote commander to TV .

2Hold POWER down, and enter your TV’s code number(s) using the

number buttons. Then release POWER.

Now you can use the POWER, VOL +/–, CH +/– and TV/VIDEO buttons to

control your TV. You can also use the buttons marked with a dot (•) to

control a Sony TV. To control the VCR, reset TV / VIDEO to VIDEO .

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until

you find the one that works with your TV.

Getting Started

Hookups

Selecting the best hookup option

There are many ways in which your VCR can be hooked up. To hook up

your VCR so that it works best for you, first scan through the table below.

Then use the accompanying diagrams and procedures on the following

pages to set up your VCR.

Step 3

If you have

TV that has audio/video input

Antenna only, no cable TV

Cable box with many scrambled

channels

No cable box or cable box with only a

few scrambled channels

Cable box with onlya few scrambled

channels, using an A/B switch

After you’ve completed the connections, follow the instructions for setup.

During setup, if you need more details on the procedure described, page

numbers are provided where you can find complete, step-by-step

instructions.

After you’ve completed the setup, you’re ready to use your VCR.

Procedures differ depending on the hookup you used. For an overview,

refer to “Quick reference to using the VCR” on the back cover.

Before you get started

• Turn off the power to all equipment.

• Do not connect the AC power cords until all of the connections are

completed.

• Be sure you make connections firmly. Loose connections may cause

picture distortion.

• If your TV doesn’t match any of the examples provided, see your nearest

Sony dealer or qualified technician.

Caution

Connections between the VCR’s VHF/UHF connector and the antenna terminals of

the TV receiver should be made only as shown in the following instructions. Failure to

do so may result in operation that violates the regulations of the Federal

Communications Commission regarding the use and operation of RF devices. Never

connect the output of the VCR to an antenna or make simultaneous (parallel) antenna

and VCR connections at the antenna terminals of your receiver.

Use

Audio/video (A/V) hookup, then

follow one of the hookups below.

Hookup 1

Hookup 2

Hookup 3

Hookup 4

Refer to

Page 8

Pages 9 and 10

Pages 11 and 12

Pages 13 and 14

Pages 15 and 16

Getting Started10

If your TV has audio/video (A/V) input jacks, you will get a better picture

and sound when you hook up your VCR using these connections. If your

TV doesn’t have A/V inputs, see the following pages for antenna or cable

hookups.

If you’re not planning to use your VCR to record programs, you’re finished

setting up the VCR after you’ve made the connections shown on this page.

If you want to record off-air or off your cable TV system, complete these

connections first, and then go to the following pages for antenna or cable

hookups.

AUse this hookup if your TV has stereo jacks

VCR

BUse this hookup if your TV doesn’t have stereo jacks

VCR

Audio/video cable (not supplied)

Audio/video (A/V) hookup

Step 3: Hookups (continued)

Audio/video cable (not supplied)

Page 8

VIDEO

AUDIO

LINE-1 IN

LINE OUT

AUDIO VIDEO

LINE-1 IN

LINE OUT

AUDIO VIDEO

VIDEO

AUDIO

Getting Started

Antenna hookup

Make the following connections if you’re using an antenna (if you don’t

have cable TV).

AUse this hookup if you’re using:

• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)

• UHF-only antenna (you get channels 14 and higher)

• Separate VHF and UHF antennas

Pages 9 and 10

BUse this hookup if you’re using a VHF-only antenna (you get

channels 2–13 only)

Hookup 1

VHF/UHF Match the type of

connector on your

TV: A, B, or C.

Rear of TV

VHFC

UHF

VHF

Rear of TV

VHF/UHF

Match the type of

connector on your

TV: A, B, or C.

BFor connector types

B and C, no UHF

connection is

required.

UHF

VHF

VCR

UHF

VHF

UHF

VCR

If you cannot connect your antenna cable to the VCR directly

If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external

antenna connector (not supplied) so you can connect the cable to the VHF/UHF IN

connector. If you have separate cables for VHF and UHF antennas, you should use a

U/V band mixer (not supplied). For details, see page 43.

OUT

VHF/UHF

OUT

VHF/UHF

continued

Getting Started12

1Set the RF UNIT switch to

CH 3 or CH 4, whichever

channel is not used in your

area. If both are used, set the

switch to either channel.

For details, see page 42. If

you made A/V connections

(page 8), you can skip this

step.

2Press EASY SET UP on the

VCR.

Hookup 1: VCR setup

1The LANGUAGE menu appears. Change the

on-screen display language to Spanish

(ESPAÑOL) or French (FRANÇAIS) if desired,

and press OK. For details, see page 17.

2The CLOCK SET menu appears. Set the clock

and press OK. For details, see page 18.

3The TUNER PRESET menu appears. Set

ANTENNA/CABLE to ANT and press OK. For

details, see page 20.

4The AUTO PRESET starts.

Step 3: Hookups (continued)

Normal display

SET UP

ENGLISH

FRANÇAIS

ESPAÑOL

LANGUAGE

CANCEL :

:OK

EASY SET UP

SET UP

CLOCK SET

CANCEL :

:OK

EASY SET UP

/1/1998 TH 12:00

SET UP

TUNER PRESET

CANCEL :

: EASY SET UP

•

ANTENNA / CABLE

ANT CABLE

SELECT : /

SET UP

SET UP IS DONE

CH3

RF UNIT

CH4

EASY SET UP

SET UP

AUTO PRESET

PLEASE WAIT

PROCESSING

Andere Handbücher für SLV-478

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Videorecorder-System Handbücher

Sony

Sony SLV-L56AR Bedienungsanleitung

Sony

Sony SLV-SE250B Bedienungsanleitung

Sony

Sony SLV-778HF - Video Cassette Recorder Benutzerhandbuch

Sony

Sony RDR VX511 - DVDr/ VCR Combo Bedienungsanleitung

Sony

Sony SLV-EX5 Bedienungsanleitung

Sony

Sony SLV-688HF - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SLV-GA30 Bedienungsanleitung

Sony

Sony SLV-798HF Bedienungsanleitung

Sony

Sony EV-S2000 Bedienungsanleitung

Sony

Sony SLV-ED1PL Bedienungsanleitung

Sony

Sony SLV-N55 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SLV-M11HF - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SLV-N80 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony DSR 11 - Professional Editing Video Cassete... Bedienungsanleitung

Sony

Sony SLV-SF950N Bedienungsanleitung

Sony

Sony UVW-1800 Bedienungsanleitung

Sony

Sony SLV-E850B Bedienungsanleitung

Sony

Sony HDCAM-SR SRW5800 Bedienungsanleitung

Sony

Sony Super Betamax SL-390 Bedienungsanleitung

Sony

Sony SLV-N99 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony DNW-75 Bedienungsanleitung

Sony

Sony SLV-ED225 Bedienungsanleitung

Sony

Sony SLV-420 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SL-HF360 Bedienungsanleitung

Beliebte Videorecorder-System Handbücher anderer Marken

Toshiba

Toshiba M-662 Bedienungsanleitung

JVC

JVC HR-J282EU Bedienungsanleitung

Magnavox

Magnavox VRU242AT Bedienungsanleitung

RCA

RCA VR634HF - Hi-Fi VCR Bedienungsanleitung

JVC

JVC HR-5910U Bedienungsanleitung

Panasonic

Panasonic ProLine AG-1320 Bedienungsanleitung

JVC

JVC HR-S8600EU Bedienungsanleitung

JVC

JVC HR-FS1U Bedienungsanleitung

Sharp

Sharp VC-H9888U Bedienungsanleitung

FUNAI

FUNAI LC-950 Bedienungsanleitung

Sharp

Sharp VC-S2000GM Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4523S Bedienungsanleitung

Aiwa

Aiwa HV-E212 Bedienungsanleitung

JVC

JVC HR-J3006UM Bedienungsanleitung

GE VG4271 Bedienungsanleitung

Panasonic

Panasonic AGDTL1P - TIME LAPSE RECORDER Bedienungsanleitung

RCA

RCA VR678HF Bedienungsanleitung

Sylvania

Sylvania SRV196 Bedienungsanleitung