Sony SLV-K877PL Bedienungsanleitung
Video Cassette
Recorder
©1997 by Sony Corporation
Operating Instructions
3-861-478-11 (1)
SLV-K877PL
Introduction
2
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.
The AC power cord must be changed only at a
qualified service shop.
Precautions
Safety
• This unit operates on 110 – 240 V AC, 50/60
Hz. Check that the unit’s operating voltage
is identical with your local power supply.
• If anything falls into the cabinet, unplug the
unit and have it checked by qualified
personnel before operating it any further.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
• Unplug the unit from the wall outlet if you
do not intend to use it for an extended
period of time. To disconnect the cord, pull
it out by the plug, never by the cord.
Installing
• Allow adequate air circulation to prevent
internal heat buildup.
• Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation
slots.
• Do not install the unit near heat sources
such as radiators or air ducts, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration or shock.
• Do not install the unit in an inclined
position. It is designed to be operated in a
horizontal position only.
• Keep the unit and cassettes away from
equipment with strong magnets, such as
microwave ovens or large loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to
a warm location, moisture may condense
inside the VCR and cause damage to the
video head and tape. When you first install
the unit, or when you move it from a cold to
a warm location, wait for about one hour
before operating the unit.
Caution
Television programs, films, video tapes and
other materials may be copyrighted.
Unauthorized recording of such material may be
contrary to the provisions of the copyright laws.
Also, use of this recorder with cable television
transmission may require authorization from the
cable television transmission and/or program
owner.
3
Introduction
Table of contents
* G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under license from Gemstar Development Corporation.
Getting Started
4 Step 1: Unpacking
5Step 2: Setting up the remote commander
6Step 3: Hookups
21 Setting the clock
22 Presetting channels
26 Setting up G-CODE*
Basic Operations
28 Playing a tape
31 Recording TV programs
34 Recording TV programs using G-
CODE
37 Setting the timer manually
Additional Operations
39 Playing/searching at various
speeds
41 Recording TV programs using the
quick timer
42 Checking/changing/cancelling
timer settings
43 Recording stereo and bilingual
programs
45 Karaoke sing-along
54 Searching with the AMS or index
function
56 Enjoying the surround sound
(Virtual Sound)
57 Adjusting the picture
58 Changing menu options
Getting Started
Editing
59 Hooking up to a VCR or stereo
system
60 Basic editing
61 Audio dubbing
Additional Information
64 General setup information
66 Troubleshooting
68 Specifications
69 Index to parts and controls
75 Index
back cover
Quick reference to using the VCR
Getting Started4
Getting Started
Step 1
Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• Size AA (R6) batteries
• 75-ohm coaxial cable with F-type
connectors
• Audio/video cable (3-phono to 3-
phono)
• Microphone
• Plug adaptor
If the plug supplied with your VCR does not
fit your power outlet, attach the supplied
adaptor to the plug.
5Getting Started
Getting Started
Inserting the batteries
Insert two size AA (R6) batteries by
matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first, then
push in and down until the positive
(+) end clicks into position.
Using the remote commander
You can use this remote
commander to operate this VCR
and a Sony TV. Buttons on the
remote commander marked with
a dot (•) can be used to operate
your Sony TV.
Step 2
Setting up the remote commander
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Remote sensor
To operate
the VCR
a Sony TV
Set TV / VIDEO to
VIDEO and point at the remote sensor on the VCR
TV and point at the remote sensor on the TV
TV␣ ␣ /␣ ␣ VIDEO
Getting Started6
Hookups
Selecting the best hookup option
There are many ways in which your VCR can be hooked up. To hook up
your VCR so that it works best for you, first scan through the table below.
Then use the accompanying diagrams and procedures on the following
pages to set up your VCR.
Step 3
If you have
TV that has audio/video inputs
Antenna only, no cable TV
Cable box with many scrambled
channels
No cable box or cable box with only a
few scrambled channels
Cable box with only a few scrambled
channels, using an A/B switch
Use
Audio/video (A/V) hookup, then
follow one of the hookups below.
Hookup 1
Hookup 2
Hookup 3
Hookup 4
Refer to
Pages 7 and 8
Pages 9 to 10
Pages 12 to 14
Pages 15 to 17
Pages 18 to 20
After you’ve completed the connections, follow the instructions for setup.
During setup, if you need more details on the procedure described, page
numbers are provided where you can find complete, step-by-step
instructions.
After you’ve completed the setup, you’re ready to use your VCR.
Procedures differ depending on the hookup you used. For an overview,
refer to “Quick reference to using the VCR” on the back cover.
Before you get started
• Turn off the power to all equipment.
• Do not connect the AC power cords until all of the connections are
completed.
• Be sure you make connections firmly. Loose connections may cause
picture distortion.
• If your TV doesn’t match any of the examples provided, see your nearest
Sony dealer or qualified technician.
7Getting Started
Getting Started
Audio/video (A/V) hookup
If your TV has audio/video (A/V) input jacks, you will get a better picture
and sound if you hook up your VCR using these connections. In addition,
for a true “home theater” experience, you should connect the audio outputs
of your VCR or TV to your stereo system. If your TV doesn’t have A/V
inputs, see the following pages for antenna or cable hookups.
If you’re not planning to use your VCR to record programs, you’re finished
setting up the VCR after you’ve made the connections shown on this page.
If you want to record off-air or off your cable TV system, complete these
connections first, and then go to the following pages for antenna or cable
hookups.
Pages 7 and 8
AUse this hookup if your TV has stereo jacks
BUse this hookup if your TV doesn’t have stereo jacks
TV
VCR
Audio/video cable (supplied)
Stereo receiver
VCR
TV
Video cable (not supplied) Audio cable (not supplied)
Stereo receiver
Notes
• To play a tape in stereo, you must use the A/V connection.
• If you want to use the Trinitron TV Synchro Play function (page 30), the connection
using the audio/video cable is necessary. (If your TV has two or more inputs,
connect the audio/video cable to the VIDEO IN 1 jacks.)
VIDEO
AUDIO
IN
AUX IN
AUDIO VIDEO
LINE-1
IN
LINE-1
OUT
continued
Audio cable (not supplied)
IN
VIDEO
AUDIO
AUDIO OUT
AUX IN
AUDIO VIDEO
LINE-1
IN
LINE-1
OUT
Getting Started8
Step 3: Hookups (continued)
After you’ve connected your TV and completed antenna or cable hookup,
use the following procedure to set up the VCR.
A/V hookup: VCR setup
SELECT :
SET : [ Vv]
[ EXECUTE ]
MENU
KARAOKE PROGRAM
TIMER SET / CHECK
SET UP KARAOKE
SET UP MENU
SET G-CODE CHANNELS
CLOCK SET
TUNER PRESET
Press MENU and select
SET UP MENU.
Set AUTO ANT SEL to OFF
and press EXECUTE.
For details, see page 58.
SET UP MENU
SELECT :
SET : [ Vv]
[ Bb]
AUDIO MIX ON OFF
AUTO STEREO
TUNER AUDIO
APC ON• OFF
MAIN• SAP
•
ON OFF•
AUTO ANT SEL ON OFF•
BUZZER ON• OFF
9Getting Started
Getting Started
Antenna hookup
Make the following connections if you’re using an antenna (if you don’t
have cable TV).
AUse this hookup if you’re using:
• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)
• UHF-only antenna (you get channels 14 and higher)
• Separate VHF and UHF antennas
BUse this hookup if you’re using a VHF-only antenna (you get
channels 2–13 only)
or
or
VHF/UHF
Match the type of
connector on your
TV: A, B, or C.
A
Rear of TV
B
VHFC
UHF
VHF
A
Rear of TV
or
or
Match the type of
connector on your
TV: A, B, or C.
BFor connector types
B and C, no UHF
connection is
required.
C
UHF
VHF
If you cannot connect your antenna cable to the VCR directly
If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external
antenna connector (not supplied) so that you can connect the cable to the VHF/UHF
IN connector. If you have separate cables for VHF and UHF antennas, you should use
a U/V band mixer (not supplied). For details, see page 65.
VCR
VHF
UHF
VCR
Hookup 1 Pages 9 to 11
UHF
VHF/UHF
IN
OUT
VHF/UHF
IN
OUT
VHF/UHF
continued
Getting Started10
Step 3: Hookups (continued)
Hookup 1: VCR setup
1The CLOCK SET menu appears. Set the clock
and press EXECUTE. For details, see page 21.
1Set the RF UNIT switch to
CH 3 or CH 4, whichever
channel is not used in your
area. If both are used, set the
switch to either channel.
For details, see page 64. If
you made A/V connections
(from page 7), you can skip
this step.
2Press EASY SET UP on the VCR with a ball-point pen, etc.
.
Normal display
2The TUNER PRESET menu appears. Set
ANTENNA/CABLE to ANT and press
EXECUTE. For details, see page 22.
3The AUTO PRESET
starts.
CH3
RF UNIT
CH4
END : [ EXECUTE ]
/2WED/1
SELECT :
SET : [ Bb]
[ Vv]
EASY SET UP
1 997 :0011
CLOCK SET
AM
EASY SET UP
ANTENNA / CABLE
CANCEL : [ EASY SET UP ]
SELECT :
NEXT : [ Bb]
[ EXECUTE ]
TUNER PRESET
ANT CABLE
•
EASY SET UP
PLEASE WAIT
AUTO PRESET
EXECUTING
TUNER PRESET
EASY SET UP
SET UP IS DONE
/
EASY
SET UP
Inhaltsverzeichnis
Andere Sony Videorecorder-System Handbücher
Sony
Sony SLV-799HF - Video Cassette Recorder Bedienungsanleitung
Sony
Sony ShowView SLV-SE510B Bedienungsanleitung
Sony
Sony DSR-1 Bedienungsanleitung
Sony
Sony SLV-585HF Bedienungsanleitung
Sony
Sony SLV-N650 Bedienungsanleitung
Sony
Sony HVR-1500A Bedienungsanleitung
Sony
Sony SLV-M20HF - Video Cassette Recorder Bedienungsanleitung
Sony
Sony PVW-2600 Bedienungsanleitung
Sony
Sony SLV-777HF - Video Cassette Recorder Bedienungsanleitung
Sony
Sony SLV-ED89AF Bedienungsanleitung
Sony
Sony SLV-ED10ME Bedienungsanleitung
Sony
Sony BKDW-515 Handbuch
Sony
Sony SLV-M20HF - Video Cassette Recorder Benutzerhandbuch
Sony
Sony SLV-799HF - Video Cassette Recorder Bedienungsanleitung
Sony
Sony SLV-N900 - 4 Head Hi-fi Stereo Vhs Video Cassette... Benutzerhandbuch
Sony
Sony SLV-KA200TK Bedienungsanleitung
Sony
Sony SLV-ME100MI Bedienungsanleitung
Sony
Sony SLV-788HF - Video Cassette Recorder Bedienungsanleitung
Sony
Sony SLV-M20HF - Video Cassette Recorder Bedienungsanleitung
Sony
Sony LX40 Bedienungsanleitung
