Sony SLV-M11HF - Video Cassette Recorder Bedienungsanleitung

3-866-141-11(1)

Video Cassette

Recorder

SLV-M11HF

Hookup/Setup

Precautions

Safety

• Operate the unit only on 120 V AC, 60 Hz.

• If anything falls into the cabinet, unplug the

unit and have it checked by qualified

personnel before operating it any further.

• This unit is not disconnected from the AC

power source (mains) as long as it is

connected to the wall outlet, even if the unit

itself has been turned off.

• Unplug the unit from the wall outlet if you

do not intend to use it for an extended

period of time. To disconnect the cord, pull

it out by the plug, never by the cord.

• One blade of the plug is wider than the

other for the purpose of safety and will fit

into the power outlet only one way. If you

are unable to insert the plug fully into the

outlet, contact your Sony dealer.

Installing

• Allow adequate air circulation to prevent

internal heat buildup.

• Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials (curtains,

draperies) that may block the ventilation

slots.

• Do not install the unit near heat sources

such as radiators or air ducts, or in a place

subject to direct sunlight, excessive dust,

mechanical vibration or shock.

• Do not install the unit in an inclined

position. It is designed to be operated in a

horizontal position only.

• Keep the unit and cassettes away from

equipment with strong magnets, such as

microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to

a warm location, moisture may condense

inside the VCR and cause damage to the

video head and tape. When you first install

the unit, or when you move it from a cold to

a warm location, wait for about three hours

before operating the unit.

* VCR Plus+, C3, ALLSET and PlusCode are trademarks of Gemstar Development Corporation. The

VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

Table of contents

4Step 1: Unpacking

5Step 2: Setting up the remote commander

8Step 3: Hookups

9Audio/video (A/V) hookup

11 Hookup 1: Using cable box control

15 Hookup 2: No cable box, or incompatible cable box with only

a few scrambled channels

19 Hookup 3: Antenna hookup

23 Hookup 4: Incompatible cable box with many scrambled

channels

27 Hookup 5: DIRECTV digital satellite receiver

30 Hookup 6: Incompatible cable box with only a few scrambled

channels, using an A/B switch

35 Selecting a language

36 Setting the clock

42 Setting up the cable box control

47 Presetting channels

53 Setting up the VCR Plus+* GOLD system

59 General setup information

61 Index to parts and controls

back cover

Index

• Remote commander

• Size AA (R6) batteries

• Audio/video cable (3-phono, 1-mini

to 3-phono, 1-mini)

• Monaural cable (1-mini to 1-mini)

Step 1

Unpacking

Check that you have received the following items with the VCR:

• Cable Mouse (cable box controller)

• 75-ohm coaxial cable with F-type

connectors

• SmartFile labels

Step 2

Setting up the remote commander

Inserting the batteries

Insert two size AA (R6) batteries by

matching the + and – on the batteries

to the diagram inside the battery

compartment.

Insert the negative (–) end first, then

push in and down until the positive (+)

end clicks into position.

Using the remote commander

You can use this remote

commander to operate this VCR

and a Sony TV or AV receiver.

Buttons on the remote

commander marked with a dot

(•) can be used to operate your

Sony TV.

The RECEIVER VOL +/– and

MUTING buttons can be used to

operate your Sony AV receiver.

Remote sensor

MUTING

RECEIVER

VOL +/–

123

456

789

Set TV RECEIVER / VIDEO to

VIDEO and point at the remote sensor on the VCR

TV RECEIVER and point at the remote sensor on the TV or

AV receiver

To operate

the VCR

a Sony TV or

AV receiver

TV RECEIVER /

VIDEO

continued

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove

the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of batteries.

• Some Sony AV receivers may not be operated with the remote commander.

Controlling other TVs with the remote commander

The remote commander is preprogrammed to control non-Sony TVs. If your TV

is listed in the table below, set the appropriate manufacturer’s code number.

1Set TV RECEIVER / VIDEO at the top of the remote commander to

␣TV␣␣RECEIVER .

2Hold down `/1, and enter your TV’s code number(s) using the number

buttons. Then release `/1.

Now you can use the

`/1

, VOL +/–, CH +/–, and TV/VIDEO buttons to

control your TV. You can also use the buttons marked with a dot (•) to control

a Sony TV. To control the VCR, reset TV RECEIVER / VIDEO to VIDEO .

Step 2: Setting up the remote commander (continued)

Notes

• If the TV uses a different remote control system from the one programmed to work

with the VCR, you cannot control your TV with the remote commander.

• If you enter a new code number, the code number previously entered will be erased.

• When you replace the batteries of the remote commander, the code number may

change. Set the appropriate code number every time you replace the batteries.

• When you press the AUDIO MONITOR button, your TV’s menu may appear on the

TV screen. To exit the TV menu, press the MENU button on the TV remote

commander or wait until the menu disappears automatically.

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until

you find the one that works with your TV.

Manufacturer Code

number

Sony 01

Akai 04

AOC 04

Centurion 12

Coronado 03

Curis-Mathes 12

Daytron 12

Emerson 03, 04, 14

Fisher 11

General Electric 06, 10

Gold Star 03, 04, 17

Hitachi 02, 03

J.C.Penny 04, 12

Manufacturer Code

number

JVC 09

KMC 03

Magnavox 03, 08, 12

Marantz 04, 13

MGA/Mitsubishi

04, 12, 13, 17

NEC 04, 12

Panasonic 06, 19

Philco 03, 04

Philips 08

Pioneer 16

Portland 03

Quasar 06, 18

Radio Shack 05, 14

Manufacturer Code

number

RCA 04, 10

Sampo 12

Sanyo 11

Scott 12

Sears 07, 10, 11

Sharp 03, 05, 18

Sylvania 08, 12

Teknika 03, 08, 14

Toshiba 07

Wards 03, 04, 12

Yorx 12

Zenith 15

Hookups

Selecting the best hookup option

There are many ways in which your VCR can be hooked up. To hook up

your VCR so that it works best for you, first scan through the table below.

Then use the accompanying diagrams and procedures on the following

pages to set up your VCR.

If you have Use Refer to

TV that has audio/video inputs Audio/video (A/V) hookup, then Pages 9 and 10

follow one of the hookups below.

Cable box that is compatible with the Hookup 1 Pages 11 to 14

VCR’s cable box control feature

No cable box or incompatible cable box Hookup 2 Pages 15 to 18

with only a few scrambled channels

Antenna only, no cable TV Hookup 3 Pages 19 to 22

Incompatible cable box with many Hookup 4 Pages 23 to 26

scrambled channels

DIRECTV* digital satellite receiver Hookup 5 Pages 27 to 29

Incompatible cable box with only a few Hookup 6 Pages 30 to 34

scrambled channels, using an A/B

switch

After you’ve completed the connections, follow the instructions for setup.

During setup, if you need more details on the procedure described, page

numbers are provided where you can find complete, step-by-step

instructions.

After you’ve completed the setup, you’re ready to use your VCR.

Procedures differ depending on the hookup you used. For an overview,

refer to “Quick reference to using the VCR” on the back cover of the

supplied operating instructions.

Before you get started

• Turn off the power to all equipment.

• Do not connect the AC power cords until all of the connections are

completed.

• Be sure you make connections firmly. Loose connections may cause

picture distortion.

• If your TV doesn’t match any of the examples provided, see your nearest

Sony dealer or qualified technician.

* DIRECTV is a trademark of DIRECTV, Inc., a unit of Hughes Electronics Corporation.

Step 3

Audio/video (A/V) hookup

If your TV has audio/video (A/V) input jacks, you will get a better picture

and sound if you hook up your VCR using these connections. In addition,

for a true “home theater” experience, you should connect the audio outputs

of your VCR or TV to your stereo system. If your TV doesn’t have A/V

inputs, see the following pages for antenna or cable hookups.

If your TV has the S-Link* (A/V bus control) function, hook up your VCR

using the connection shown on page 10. Your TV will automatically switch

to the A/V inputs for your VCR when you play back or operate menu on the

VCR.

If you’re not planning to use your VCR to record programs, you’re finished

setting up the VCR after you’ve made the connections shown on pages 9 and

10. If you want to record off-air or off your cable TV system, complete these

connections first, and then go to the following pages for antenna or cable

hookups.

* S-Linkis a trademark of Sony Corporation.

AUse this hookup if your TV has stereo jacks

Pages 9 and 10

Audio/video cable (supplied)

VCR Stereo receiver

* Do not connect the miniplugs for this hookup.

VCR Stereo receiver

BUse this hookup if your TV doesn’t have stereo jacks

continued

Audio cable (not supplied)

Video cable (not supplied)

Audio cable (not supplied)

LINE-1

LINE

OUT

AUDIO VIDEO

VIDEO

AUDIO

AUDIO OUT

AUX IN

VIDEO

AUDIO

AUX IN

LINE-1

LINE

OUT

AUDIO VIDEO

Note

• To play a tape in stereo, you must use the A/V connection.

CUse this hookup if your TV has the S-Linkfunction

A/V hookup: VCR setup

VCR

After you’ve connected your TV and completed antenna or cable hookup,

use the following procedure to set up the VCR.

Caution

Connections between the VCR’s VHF/UHF connector and the antenna terminals of

the TV receiver should be made only as shown in the following instructions. Failure

to do so may result in operation that violates the regulations of the Federal

Communications Commission regarding the use and operation of RF devices. Never

connect the output of the VCR to an antenna or make simultaneous (parallel) antenna

and VCR connections at the antenna terminals of your receiver.

Note to CATV system installer (in USA)

This reminder is provided to call the CATV system installer’s attention to Article 820-

40 of the NEC that provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

Press MENU and select

ADVANCED OPTIONS. Set AUTO ANT SEL to OFF and

press OK.

For details, see page 34 of the

supplied operating instructions.

Stereo receiver

Audio/video cable (supplied)

Step 3: Hookups (continued)

Audio cable (not supplied)

ADVANCED OPTIONS

CLOCK SET

TUNER PRESET

TIMER SET / CHECK

LANGUAGE

CABLE BOX CONTROL

SMARTFILE EDIT

SET VCR Plus+ CHANNELS

ADVANCED OPTIONS

SHARPNESS

TUNER AUDIO

AUDIO MIX

AUTO STEREO ON OFF

ON OFF

MAIN SAP

page1

AUTO ANT SEL

Use to se l ec t an

tem, then push

LH––

S-LINK

AUDIO VIDEO

VIDEO

AUDIO AUDIO OUT

AUX IN

S-LINK

LINE-1

LINE

OUT

Andere Handbücher für SLV-M11HF - Video Cassette Recorder

Inhaltsverzeichnis

Andere Sony Videorecorder-System Handbücher

Sony

Sony SLV-M11HF - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SLV-AV100 Bedienungsanleitung

Sony

Sony VCRplus+ SLV-688HF Bedienungsanleitung

Sony

Sony HDV HVR-1500 Bedienungsanleitung

Sony

Sony SLV-420 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SLV-AX20 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony HR-A56U Bedienungsanleitung

Sony

Sony SLV-SE610G Bedienungsanleitung

Sony

Sony VO-9800 Bedienungsanleitung

Sony

Sony BETACAM SP 2000 PRO Bedienungsanleitung

Sony

Sony Video 8 EV-A50 Bedienungsanleitung

Sony

Sony SLV-X9D Bedienungsanleitung

Sony

Sony HDCAM J-H1 Bedienungsanleitung

Sony

Sony SLV-SE310 Bedienungsanleitung

Sony

Sony SLV-SE850G Bedienungsanleitung

Sony

Sony SL-HF300 Bedienungsanleitung

Sony

Sony SLV-GA30 Bedienungsanleitung

Sony

Sony SLV-ED1ME Bedienungsanleitung

Sony

Sony DNW-A25WS Bedienungsanleitung

Sony

Sony BR-D95U Bedienungsanleitung

Sony

Sony HVR M25U - Professional Video Cassete... Bedienungsanleitung

Sony

Sony SLV-XA125TK Bedienungsanleitung

Sony

Sony DHR-1000 Bedienungsanleitung

Sony

Sony SLV-N55 - Video Cassette Recorder Bedienungsanleitung

Beliebte Videorecorder-System Handbücher anderer Marken

Toshiba

Toshiba M-662 Bedienungsanleitung

JVC

JVC HR-J282EU Bedienungsanleitung

Panasonic

Panasonic AGDTL1P - TIME LAPSE RECORDER Bedienungsanleitung

RCA

RCA VR678HF Bedienungsanleitung

Sylvania

Sylvania SRV196 Bedienungsanleitung

Akai

Akai VS-606EA Bedienungsanleitung

Fisher

Fisher FVH-8300 Bedienungsanleitung

Zenith

Zenith VRL4270HF Bedienungs- und Wartungshandbuch

Panasonic

Panasonic Omnivision PV-4661 Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4601 Bedienungsanleitung

GE VG2050 Bedienungsanleitung

Sanyo

Sanyo TLS-9072 Bedienungsanleitung

Philips

Philips VR969/05 Bedienungsanleitung

Memorex

Memorex MVR4041 Bedienungsanleitung

Arm Electronics

Arm Electronics VCR800 Bedienungsanleitung

Panasonic

Panasonic NV-SD200BA Bedienungsanleitung

Sanyo

Sanyo VHR-230 series Bedienungsanleitung

Panasonic

Panasonic NV-SJ412EE Bedienungsanleitung