Sony SLV-T2000MN Bedienungsanleitung

Sony Corporation Printed in Japan

Index

A, B

Accessories supplied 4

Adjusting

picture 50

tracking 50

Aerial hookup 9

AFT (Auto Fine Tuning) 21

ATP 14

Audio track 48

Audio dubbing 57

Cancelling timer settings 44

Changing timer settings 44

Cleaning the video

heads 62

Clock setting 27

Colour system 2

Connecting

the VCR and your TV 9

to a stereo system 11

to a TV with a EURO-AV

connector 10

Counter 30, 32

Dubbing. See Editing

E, F

EASY SET UP 14

EURO-AV connection

Editing 54

G-CODE

recording 35

setting up 22

Guide channel

setting 35

Hi8 video system 65

Hi-fi audio sound 48

I, J, K

Index

searching 49

Language selecting 18

LP mode 32

Monitoring

during playback 53

during recording 32

NICAM broadcasts 46

Normal audio track 48

OPC (Optimum Picture

Control) 50

PDC (Programme Delivery

Control) 40

Picture adjustment. See

Adjusting

Playback 29

at various speeds 41

skip 41

slow motion 42

Presetting channels 14, 19

Quick timer 43

Recording 31

bilingual

programmes 46

saving 33

stereo programmes 46

using G-CODE 35

While watching another

programme 33

Remote commander 5

RF channel 12

Safety tab 33

Searching

at various speeds 41

using the index

function 49

SP mode 32

T, U

Timer recording 35, 38, 43

cancelling timer

settings 44

changing timer

settings 44

checking timer

settings 44

daily/weekly

recording 36, 40

overlapping timer

recordings 45

using G-CODE 35

Tracking adjustment. See

Adjusting

V, W, X, Y, Z

VPS (Video Programme

System) 40

ZWEITON broadcasts 46

Index

Video Cassette

Recorder

SLV-T2000MN/AS

Operating Instructions

3-860-334-11 (1)

PAL

Introduction

WARNING

To prevent fire or shock hazard, do not expose

the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel

only.

Precautions

Safety

• This unit operates on 220 – 240 V AC, 50 Hz.

Check that the unit’s operating voltage is

identical with your local power supply.

• If anything falls into the cabinet, unplug the

unit and have it checked by qualified

personnel before operating it any further.

• The unit is not disconnected from the mains

as long as it is connected to the mains outlet,

even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you

do not intend to use it for an extended

period of time. To disconnect the cord, pull

it out by the plug, never by the cord.

Installing

• Allow adequate air circulation to prevent

internal heat buildup.

• Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials (curtains,

draperies) that may block the ventilation

slots.

• Do not install the unit near heat sources

such as radiators or air ducts, or in a place

subject to direct sunlight, excessive dust,

mechanical vibration or shock.

• Do not install the unit in an inclined

position. It is designed to be operated in a

horizontal position only.

• Keep the unit and cassettes away from

equipment with strong magnets, such as

microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to

a warm location, moisture may condense

inside the VCR and cause damage to the

video head and tape. When you first install

the unit, or when you move it from a cold to

a warm location, wait for about one hour

before operating the unit.

Caution

Television programmes, films, video tapes and

other materials may be copyrighted.

Unauthorized recording of such material may

be contrary to the provisions of the copyright

laws. Also, use of this recorder with cable

television transmission may require

authorization from the cable television

transmitter and/or programme owner.

Colour system

This VCR is designed to record and playback

using the PAL colour system. Recording of

video sources based on other colour systems

cannot be guaranteed.

Introduction

Table of contents

Getting Started

* G-CODE is a trademark applied for by Gemstar Development Corp. G-CODE system is

manufactured under license from Gemstar Development Corporation.

Getting Started

4Step 1: Unpacking

5Step 2: Setting up the remote commander

9Step 3: Connecting the VCR

12 Step 4: Tuning your TV to the VCR

14 Step 5: Setting up the VCR with EASY SET UP

18 Manual setup —

Selecting a language, Presetting channels, Setting up G-CODE*,

Changing programme positions, Setting the clock

51 Changing menu options

53 Using the 8 mm deck and VHS

deck at the same time

Editing

54 One button dubbing

55 Cut editing

57 Audio dubbing (VHS deck only)

59 Editing with another VCR

Additional Information

62 Troubleshooting

65 H(high eight) video system

66 Specifications

67 Index to parts and controls

Back cover

Index

Basic Operations

29 Playing a tape

31 Recording TV programmes

35 Recording TV programmes using

G-CODE

38 Setting the timer manually

Additional Operations

41 Playing/searching at various

speeds

43 Recording TV programmes using

the quick timer

44 Checking/changing/cancelling

timer settings

46 Recording stereo and bilingual

programmes

49 Searching using the index

function (VHS deck only)

50 Adjusting the picture

(VHS deck only)

Getting Started4

Getting Started

Step 1

Unpacking

Check that you have received the following items with the VCR:

• Aerial cable

• S-video cable

• Mains lead (2)

• R6 (size AA) batteries

• Remote commander

• Audio / video cable

• 21-pin adaptor

Checking your model name

The instructions in this manual are for the 2 models : SLV-T2000MN,

T2000AS. Check your model number by looking at the rear panel of

your unit. The SLV-T2000AS is the model used for illustration

purposes. Any difference in operation is clearly indicated in the text,

for example, “SLV-T2000MN only.”

Getting Started

TV / VIDEO

To operate

the VCR

a Sony TV

Set TV / VIDEO to

VIDEO and point at the remote sensor on the VCR

TV and point at the remote sensor on the TV

continued

Step 2

Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA)

batteries by matching the + and

– on the batteries to the

diagram inside the battery

compartment.

Using the remote commander

You can use this remote

commander to operate this

VCR and a Sony TV. Buttons

on the remote commander

marked with a dot (•) can be

used to operate your Sony TV.

Remote

sensor

Getting Started6

Step 2 : Setting up the remote commander (continued)

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove

the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of batteries.

Turn the TV into standby or active mode

Select an input source of the TV either from

aerial in or from line in

Select the programme position of the TV

Adjust the volume of the TV

Switch to TV (Teletext off)

Switch to Teletext

Select the sound

Use FASTEXT

Call up on-screen display

Change the Teletext page

Operate TV menu options

Press

u(on/standby)

TV/VIDEO

Programme number buttons

PROG +/–

VOL +/–

;(TV)

V(Teletext)

AUDIO MONITOR

FASTEXT buttons

DISPLAY

√/◊

Menu button

TV/VIDEO

;

DISPLAY

FASTEXT buttons

Menu button AUDIO

MONITOR

Programme

number

buttons

PROG+/–/

√/◊

VOL+/–

TV control buttons

Getting Started

continued

Setting the COMMAND MODE switch

To remotely control the Sony VCR

with this remote commander, set

COMMAND MODE on the

remote commander to the same

position as that on the VCR.

Usually set to VTR 3. Change the

position as shown below to

control other Sony VCRs:

VTR 1: For Sony Betamax format VCRs

VTR 2: For Sony 8mm format VCRs

VTR 3: For Sony VHS format VCRs

Controlling other TVs with the remote commander

The remote commander is

preprogrammed to control non-

Sony TVs. If your TV is listed in

the table on the next page, set the

appropriate manufacturer’s code

number.

1Set TV / VIDEO at the top of the remote commander to TV .

2Hold down u, and enter your TV’s code number(s) using the number

buttons. Then release u.

Now you can use the following TV control buttons to control your TV:

u(on/standby), TV / VIDEO , programme number buttons, PROG +/

–, VOL +/–, ;(TV), V(Teletext), FASTEXT buttons and WIDE with

some TVs.

COMMAND

MODE

TV /

VIDEO

Getting Started8

Step 2 : Setting up the remote commander (continued)

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until

you find the one that works with your TV.

To make wide mode settings, see the footnotes below this table for the

applicable code numbers.

Manufacturer

Sony

Aiwa

Akai

Blaupunkt

Brionvega

C.G.M

Colonad

Dual

Emerson

Fenner

Ferguson

Gold Star

Grundig

Hitachi

Hyper

Inno-Hit

Irradio

ITT

JVC

Loewe

Mitsubishi

Mivar

Manufacturer

NEC

Nokia

Nordmende

Orion

Panasonic

Philips

Phonola

Pioneer

Saba

Samsung

Sanyo

Schneider

Seleco

Sharp

Siemens

Sinudyne

TEAC

Telefunken

Thomson

Toshiba

White Westinghouse

Code number

01*1, 02, 03, 04, 05

10, 21

03, 04

30, 31

03, 04, 17

10*1, 11*1

15, 16, 69*3

33*1

27*1, 28*1, 50*1, 51*1

Code number

15, 16, 69*3

35, 42

47, 48

17*1, 49

06*1, 07*1, 08*1

18, 19

12, 13

22, 23

43*2

*1Press WIDE to switch the wide picture mode on or off.

*2Press WIDE, then press VOL +/– to select the wide picture mode you want.

*3Press WIDE. The menu appears on the TV screen. Then, press

CURSOR >/./?//to select the wide picture you want and press EXECUTE.

Notes

• If the TV uses a different remote control system from the one programmed to work

with the VCR, you cannot control your TV with the remote commander.

• If you enter a new code number, the code number previously entered will be erased.

• When you replace the batteries of the remote commander, the code number

automatically resets to 01 (Sony). Reset the appropriate code number.

Getting Started

AERIAL

OUT

AERIAL

OUT

Connecting the VCR

Step 3

: Signal flow

AERIAL IN

Aerial cable AERIAL IN

AERIAL OUT

AC IN to mains

1Disconnect the aerial cable from your TV

and connect it to AERIAL IN on the rear

panel of the VCR.

2Connect AERIAL OUT of the VCR and

the aerial input of your TV using the

supplied aerial cable.

3Connect AC IN of the VCR to the mains

using the supplied mains lead.

continued

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Videorecorder-System Handbücher

Sony

Sony SLV-D300P Operating Instructions (SLVD300P) Bedienungsanleitung

Sony

Sony SLV-KH9ME/PS Bedienungsanleitung

Sony

Sony SLV-M20HF - Video Cassette Recorder Benutzerhandbuch

Sony

Sony SVT-168E Bedienungsanleitung

Sony

Sony DNW-A220 Bedienungsanleitung

Sony

Sony SLV-SE350K Bedienungsanleitung

Sony

Sony SLV-GA30 Bedienungsanleitung

Sony

Sony SLV-N51 - Video Cassette Recorder Bedienerhandbuch

Sony

Sony SLV-N99 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony RDR VX555 - DVDr/ VCR Combo Bedienungsanleitung

Sony

Sony Handycam CCD-TR44 Bedienungsanleitung

Sony

Sony VCRplus+ SLV-775HF Bedienungsanleitung

Sony

Sony SLV-662HF Operating Instructions (SLV-662HF / 679HF / 679HF PX... Bedienungsanleitung

Sony

Sony SLV-390 Bedienungsanleitung

Sony

Sony PVW-2800 Bedienungsanleitung

Sony

Sony SLV-N51 - Video Cassette Recorder Bedienungsanleitung

Sony

Sony SLV-688HF - Video Cassette Recorder Bedienungsanleitung

Sony

Sony DSR 45 - Professional Editing Video Cassete... Bedienungsanleitung

Sony

Sony SLV-SE70NP1, SLV-SE70NP2, SLV- Bedienungsanleitung

Sony

Sony SLV-GA60MJ Bedienungsanleitung

Sony

Sony SLV-975HF Bedienungsanleitung

Sony

Sony SL-20 Bedienungsanleitung

Sony

Sony SLV-SE240B Bedienungsanleitung

Sony

Sony SLV-SE35EG Bedienungsanleitung

Beliebte Videorecorder-System Handbücher anderer Marken

Toshiba

Toshiba M-662 Bedienungsanleitung

JVC

JVC HR-J282EU Bedienungsanleitung

Magnavox

Magnavox VRU242AT Bedienungsanleitung

RCA

RCA VR634HF - Hi-Fi VCR Bedienungsanleitung

JVC

JVC HR-5910U Bedienungsanleitung

Panasonic

Panasonic ProLine AG-1320 Bedienungsanleitung

JVC

JVC HR-S8600EU Bedienungsanleitung

JVC

JVC HR-FS1U Bedienungsanleitung

Sharp

Sharp VC-H9888U Bedienungsanleitung

FUNAI

FUNAI LC-950 Bedienungsanleitung

Sharp

Sharp VC-S2000GM Bedienungsanleitung

Panasonic

Panasonic Omnivision PV-V4523S Bedienungsanleitung

Aiwa

Aiwa HV-E212 Bedienungsanleitung

JVC

JVC HR-J3006UM Bedienungsanleitung

GE VG4271 Bedienungsanleitung

Panasonic

Panasonic AGDTL1P - TIME LAPSE RECORDER Bedienungsanleitung

RCA

RCA VR678HF Bedienungsanleitung

Sylvania

Sylvania SRV196 Bedienungsanleitung